☆ 4.7 Article

Multi-objective optimization of a mini channeled cold plate for using thermal management of a Li-Ion battery

ENERGY (2022)

Related references

Note: Only part of the references are listed.

Article Thermodynamics

Experimental study of thermal management system for cylindrical Li-ion battery pack based on nanofluid cooling and copper sheath

Amirhosein Sarchami et al.

Summary: A novel thermal management system was developed and studied experimentally to control the temperature of cylindrical lithium-ion batteries. The study found that increasing the concentration of alumina nanoparticles and inflow velocity can significantly reduce the maximum temperature and temperature non-uniformity, while liquid cooling with stair channel can effectively reduce the temperature of the battery pack.

INTERNATIONAL JOURNAL OF THERMAL SCIENCES (2022)

Add to Collection

Article Thermodynamics

Synergistic effect of insulation and liquid cooling on mitigating the thermal runaway propagation in lithium-ion battery module

Xinyu Rui et al.

Summary: This study investigated the synergy of heat dissipation and thermal insulation in the elimination of thermal runaway propagation (TRP) in Li-ion batteries of electric vehicles (EVs). It was found that pure liquid cooling alone is not effective in mitigating TRP, and successful inhibition of TRP requires the cooperation of thermal insulation and liquid cooling. Six critical conditions for TRP prevention were identified, and a theoretical diagram illustrating the relationship between heat dissipation and thermal insulation was obtained from modeling analysis.

APPLIED THERMAL ENGINEERING (2021)

Add to Collection

Article Thermodynamics

Comparison of lumped and 1D electrochemical models for prismatic 20Ah LiFePO4 battery sandwiched between minichannel cold-plates

Sandeep Dattu Chitta et al.

Summary: This paper provides a detailed comparison study on the prediction accuracy of two different and simplified battery models, revealing that while the Lumped model closely matches the Li-ion model at lower discharge rates, there is a significant difference at higher discharge rates due to the non-consideration of chemical reactions. It is suggested to use the Lumped model for preliminary studies in designing the BTMS system.

APPLIED THERMAL ENGINEERING (2021)

Add to Collection

Article Thermodynamics

A hybrid battery thermal management system for electric vehicles under dynamic working conditions

Q. L. Yue et al.

Summary: The study develops a hybrid battery thermal management system to address the temperature issues of lithium-ion battery packs used in EVs, successfully reducing maximum temperature, minimizing temperature non-uniformity, and with low energy consumption, showing promising prospects for practical use.

INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER (2021)

Add to Collection

Article Thermodynamics

A novel liquid cooling plate concept for thermal management of lithium-ion batteries in electric vehicles

Mohsen Akbarzadeh et al.

Summary: This paper presents an innovative liquid cooling plate (LCP) embedded with phase change material (PCM) for thermal management of electric vehicle (EV) batteries. The hybrid LCP, combining active and passive cooling methods, is 36% lighter than traditional aluminum LCP and provides heating solution to slow temperature loss. Experimental and computational analyses show that the hybrid LCP reduces energy consumption and improves temperature uniformity, making it a promising thermal management solution for EVs.

ENERGY CONVERSION AND MANAGEMENT (2021)

Add to Collection

Review Thermodynamics

A review on recent progress, challenges and perspective of battery thermal management system

Jiayuan Lin et al.

Summary: This article summarizes thermal management models from literature and categorizes multi-physical battery thermal management systems. Emergency battery thermal management methods are also discussed. A novel digital solution based on the CHAIN framework is proposed to improve temperature control strategy for EV power systems.

INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER (2021)

Add to Collection

Review Green & Sustainable Science & Technology

A review on hybrid thermal management of battery packs and it's cooling performance by enhanced PCM

G. Murali et al.

Summary: Power batteries in electric vehicles release a significant amount of heat during charging and discharging, necessitating the use of a Battery Thermal Management System (BTMS) to regulate temperature rise and distribution for improved battery lifespan, efficiency, and safety. Among various BTMS options, Phase Change Material (PCM) stands out for its appealing features such as low parasitic power, low weight, and uniform temperature distribution. The study introduces a Hybrid Thermal Management System with PCM for enhanced cooling, and summarizes techniques to enhance thermal conductivity of PCM. Additionally, it reviews research on key parameters affecting system performance and proposes conclusions based on previous studies on PCM cooling.

RENEWABLE & SUSTAINABLE ENERGY REVIEWS (2021)

Add to Collection

Article Energy & Fuels

Developments in battery thermal management systems for electric vehicles: A technical review

Pranjali R. Tete et al.

Summary: In the era of sustainable energy revolution, battery storage has emerged as a crucial field, especially in the context of electric vehicles. Efficient energy storage and retrieval in batteries, along with the operating temperature of electric vehicle batteries, are vital for performance optimization. Various cooling systems, such as air, liquid, phase change material, heat pipe, and refrigeration methods, have been discussed in depth in recent experimental and numerical analyses of battery thermal management systems (BTMS).

JOURNAL OF ENERGY STORAGE (2021)

Add to Collection

Article Thermodynamics

A passive thermal management system of Li-ion batteries using PCM composites: Experimental and numerical investigations

Mohamed Moussa El Idi et al.

Summary: This study focuses on the design of an optimal thermal management system using a PCM-Metal Foam composite at the scale of Li-ion battery cells, with a mathematical and numerical model developed to study the heat absorption ability of PCM and PCM-Metal foam composite. The results indicated that the addition of aluminum foam can improve thermal management efficiency, and underestimating the thickness may lead to extreme temperatures.

INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER (2021)

Add to Collection

Article Energy & Fuels

Numerical investigation on thermal behaviour of 5 x 5 cell configured battery pack using phase change material and fin structure layout

V. G. Choudhari et al.

Summary: This study evaluates the thermal performance of lithium-ion battery modules using phase change material cooling and proposes different fin structure layouts to minimize internal heat accumulation. By investigating rest time, convection effect, and fin structure, it is possible to reduce maximum temperature, recover melting fraction, and optimize the thermal performance of the battery pack.

JOURNAL OF ENERGY STORAGE (2021)

Add to Collection

Article Energy & Fuels

Enhancement of lithium-ion battery thermal management with the divergent-shaped channel cold plate

Wei Kong et al.

Summary: The new cold plate design utilizing divergent-shaped channels has enhanced heat dissipation capacity and minimized pressure drop, contributing to the development of effective battery cooling systems for electric vehicles.

JOURNAL OF ENERGY STORAGE (2021)

Add to Collection

Article Energy & Fuels

A lightweight liquid cooling thermal management structure for prismatic batteries

Zhiguo Tang et al.

Summary: A novel lightweight battery thermal management system (BTMS) structure was developed, and numerical simulation demonstrated superior cooling effects of two designs with low weight ratios.

JOURNAL OF ENERGY STORAGE (2021)

Add to Collection

Article Thermodynamics

Experimental investigation of thermal performance of novel cold plate design used in a Li-ion pouch-type battery

Orhan Kalkan et al.

Summary: The study investigated the thermal performance of water-cooled cold plates used in thermal management of batteries for electric vehicles. It found that lower coolant inlet temperature has a significant impact on battery surface temperature, while the use of mini channel cold plate resulted in a significant reduction in battery surface temperature and improved temperature homogeneity.

APPLIED THERMAL ENGINEERING (2021)

Add to Collection

Article Thermodynamics

Cooling performance optimization of air-cooled battery thermal management system

Meiwei Wang et al.

Summary: A new method was introduced in this study to improve the cooling performance of air-cooled battery thermal management system (BTMS) by adding parallel plates. The results showed that this method effectively enhanced the cooling efficiency of the BTMS, reducing the maximum temperature and temperature difference significantly.

APPLIED THERMAL ENGINEERING (2021)

Add to Collection

Article Thermodynamics

Novel battery thermal management system for electric vehicles with a loop heat pipe and graphite sheet inserts

Marco Bernagozzi et al.

Summary: An innovative thermal management system for a 3-cell battery module, utilizing a flat plate Loop Heat Pipe and graphite sheet inserts, has been proposed to address key Electric Vehicles issues including maximum temperature during fast charging and parasitic power consumption. This design allows for efficient heat transfer without the need for electrical power, reducing maintenance requirements compared to standard systems, and has been validated to meet battery thermal requirements with improved temperature control.

APPLIED THERMAL ENGINEERING (2021)

Add to Collection

Article Thermodynamics

Performance analysis and optimization of a novel cooling plate with non-uniform pin-fins for lithium battery thermal management

Rongchao Zhao et al.

Summary: This paper investigates the performance of a cooling plate with non-uniform pin-fins using experimental and CFD methods, optimizing the design through multi-objective optimization algorithm and comparing it with a traditional design. The optimized design shows significant reductions in power consumption, weight, and temperature standard deviation, as well as a decrease in maximum temperature.

APPLIED THERMAL ENGINEERING (2021)

Add to Collection

Article Thermodynamics

Numerical investigation of the direct liquid cooling of a fast-charging lithium-ion battery pack in hydrofluoroether

Xiaojun Tan et al.

Summary: This paper proposes a novel direct liquid battery cooling system for fast-charging battery packs based on a hydrofluoroether coolant. Through high-fidelity CFD simulations, it is found that optimizing channel design and coolant velocity can improve energy density and reduce power consumption, while a multilayer structure and cross-flowing configuration can reduce temperature difference and standard deviation.

APPLIED THERMAL ENGINEERING (2021)

Add to Collection

Article Thermodynamics

Systematic evaluation of a flat-heat-pipe-based thermal management: Cell-to-cell variations and battery ageing

Z. Liang et al.

Summary: This study investigates the temperature difference and local cell temperature in a battery pack, finding that high tolerance levels and battery ageing can lead to adverse effects on heat pipe cooling. The flat-heat-pipe-based BTM method with a high heat transfer coefficient successfully controls the temperature and temperature difference of a battery pack.

APPLIED THERMAL ENGINEERING (2021)

Add to Collection

Article Thermodynamics

Effect analysis on heat dissipation performance enhancement of a lithium-ion-battery pack with heat pipe for central and southern regions in China

E. Jiaqiang et al.

Summary: A heat pipe heat dissipation model for a lithium-ion battery pack in central and southern China was established, investigating the effects of different fin spacing and thickness on heat transfer. Optimal fin structure parameters were determined based on heat dissipation changes, and battery temperature distribution under different discharge rates was analyzed. The battery pack using the HP showed effective temperature control under various discharge rates.

ENERGY (2021)

Add to Collection

Article Chemistry, Physical

Active air cooling thermal management system based on U-shaped micro heat pipe array for lithium-ion battery

Ruyang Ren et al.

Summary: A new active air cooling thermal management system based on U-shaped micro heat pipe array has been developed, and comparative experiments have shown that it has the best cooling performance even under high charge and discharge rates.

JOURNAL OF POWER SOURCES (2021)

Add to Collection

Review Green & Sustainable Science & Technology

A review on thermal management performance enhancement of phase change materials for vehicle lithium-ion batteries

Zu-Guo Shen et al.

Summary: Phase change materials (PCMs) have advantages such as low energy consumption, high temperature uniformity, and affordable price in managing the temperature of lithium-ion batteries in new energy vehicles. However, PCM-based battery thermal management systems suffer from low heat extraction rate and limited thermal storage capacity. To address these flaws, three enhancement strategies have been developed, leading to improved thermal management performance. Challenges still remain for the commercialization of PCM-based systems.

RENEWABLE & SUSTAINABLE ENERGY REVIEWS (2021)

Add to Collection

Article Energy & Fuels

Heat dissipation optimization for a serpentine liquid cooling battery thermal management system: An application of surrogate assisted approach

Ningbo Wang et al.

Summary: This paper studied a liquid cooling battery thermal management system incorporating serpentine microchannels, and successfully optimized the parameters to reduce battery temperature and pressure, improving heat dissipation performance while reducing energy consumption.

JOURNAL OF ENERGY STORAGE (2021)

Add to Collection

Article Energy & Fuels

Hybrid cooling based battery thermal management using composite phase change materials and forced convection

Mohamed Moussa El Idi et al.

Summary: This study investigates the thermal management of Lithium-ion batteries at the individual cell scale using a novel system with phase change material (PCM) composite. The system successfully maintained the battery temperature around the optimal operating temperature of 25 degrees Celsius and found that the addition of aluminum foam enhanced the thermal management efficiency of the cell.

JOURNAL OF ENERGY STORAGE (2021)

Add to Collection

Article Energy & Fuels

Experimental and numerical investigation of the LiFePO4 battery cooling by natural convection

Orhan Kalkan et al.

Summary: The thermal performance of a LiFePO4 pouch type battery under different discharge rates was experimentally and numerically investigated. It was found that natural convection cooling is not sufficient for the battery at high discharge rates.

JOURNAL OF ENERGY STORAGE (2021)

Add to Collection

Article Energy & Fuels

Numerical study of novel liquid-cooled thermal management system for cylindrical Li-ion battery packs under high discharge rate based on AgO nanofluid and copper sheath

Mahdi Tousi et al.

Summary: A novel battery thermal management system based on AgO nanofluid is designed to maintain the maximum temperature and temperature homogeneity in 18650/21700 types lithium-ion batteries. The study shows that at high discharge rates, the use of optimal inflow velocity and nanofluid volume fraction as coolant can effectively reduce the temperature of the battery pack. Comparing the 18650 and 21700 types lithium-ion battery thermal management systems, the 21700 type battery pack shows promising potential.

JOURNAL OF ENERGY STORAGE (2021)

Add to Collection

Article Energy & Fuels

Investigation of thermal management of lithium-ion battery based on micro heat pipe array

Lincheng Wang et al.

Summary: This study proposed a heating method based on MHPA for addressing the performance deterioration of lithium-ion batteries in low temperatures, achieving rapid and uniform heating according to the established three-dimensional model. Additionally, the interaction between heat dissipation and heating modules in the integrated TMS with MHPA was analyzed, indicating that heating components can enhance high-temperature heat dissipation in the battery pack.

JOURNAL OF ENERGY STORAGE (2021)

Add to Collection

Article Thermodynamics

Air and PCM cooling for battery thermal management considering battery cycle life

Fenfang Chen et al.

APPLIED THERMAL ENGINEERING (2020)

Add to Collection

Article Chemistry, Physical

Experimental investigation of the effect of vibration on phase change material (PCM) based battery thermal management system

Naveen Joshy et al.

JOURNAL OF POWER SOURCES (2020)

Add to Collection

Review Energy & Fuels

Research progress on power battery cooling technology for electric vehicles

Mengyao Lu et al.

JOURNAL OF ENERGY STORAGE (2020)

Add to Collection

Article Energy & Fuels

Impact of high-temperature environment on the optimal cycle rate of lithium-ion battery

Dongxu Ouyang et al.

JOURNAL OF ENERGY STORAGE (2020)

Add to Collection

Article Thermodynamics

Multi-objective optimization of a liquid cooled battery module with collaborative heat dissipation in both axial and radial directions

Zehua Zhu et al.

INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER (2020)

Add to Collection

Article Energy & Fuels

The EV revolution: The road ahead for critical raw materials demand

Ben Jones et al.

APPLIED ENERGY (2020)

Add to Collection

Article Chemistry, Physical

Recent developments in the passive and hybrid thermal management techniques of lithium-ion batteries

Jay R. Patel et al.

JOURNAL OF POWER SOURCES (2020)

Add to Collection

Article Chemistry, Physical

Introducing new designs of minichannel cold plates for the cooling of Lithium-ion batteries

T. Amalesh et al.

JOURNAL OF POWER SOURCES (2020)

Add to Collection

Article Thermodynamics

Thermofluidic modeling and temperature monitoring of Li-ion battery energy storage system

Fengbo Tao et al.

APPLIED THERMAL ENGINEERING (2020)

Add to Collection

Article Thermodynamics

A comprehensive analysis and optimization process for an integrated liquid cooling plate for a prismatic lithium-ion battery module

Siqi Chen et al.

APPLIED THERMAL ENGINEERING (2019)

Add to Collection

Review Chemistry, Physical

A survey of methods for monitoring and detecting thermal runaway of lithium-ion batteries

Zhenghai Liao et al.

JOURNAL OF POWER SOURCES (2019)

Add to Collection

Article Thermodynamics

Investigation of thermal management for lithium-ion pouch battery module based on phase change slurry and mini channel cooling plate

Fanfei Bai et al.

ENERGY (2019)

Add to Collection

Article Thermodynamics

The performance management of a Li-ion battery by using tree-like mini-channel heat sinks: Experimental and numerical optimization

Huan-ling Liu et al.

ENERGY (2019)

Add to Collection

Review Thermodynamics

Thermal issues about Li-ion batteries and recent progress in battery thermal management systems: A review

Huaqiang Liu et al.

ENERGY CONVERSION AND MANAGEMENT (2017)

Add to Collection

Article Energy & Fuels

Liquid cooling based on thermal silica plate for battery thermal management system

Cong Wang et al.

INTERNATIONAL JOURNAL OF ENERGY RESEARCH (2017)

Add to Collection

Article Thermodynamics

Numerical modeling and experimental investigation of a prismatic battery subjected to water cooling

S. Panchal et al.

NUMERICAL HEAT TRANSFER PART A-APPLICATIONS (2017)

Add to Collection

Review Green & Sustainable Science & Technology

Review on thermal management systems using phase change materials for electronic components, Li-ion batteries and photovoltaic modules

Ziye Ling et al.

RENEWABLE & SUSTAINABLE ENERGY REVIEWS (2014)

Add to Collection

Article Electrochemistry

Multi-Domain Modeling of Lithium-Ion Batteries Encompassing Multi-Physics in Varied Length Scales

Gi-Heon Kim et al.

JOURNAL OF THE ELECTROCHEMICAL SOCIETY (2011)

Add to Collection

Article Chemistry, Physical

A two-dimensional modeling of a lithium-polymer battery

Ki Hyun Kwon et al.

JOURNAL OF POWER SOURCES (2006)

Add to Collection

Article Computer Science, Interdisciplinary Applications

Approximation methods in multidisciplinary analysis and optimization: a panel discussion

TW Simpson et al.

STRUCTURAL AND MULTIDISCIPLINARY OPTIMIZATION (2004)

Add to Collection

© Peeref 2019-2024. All rights reserved.