☆ 4.7 Article

Opuntia Ficus Indica based green composites for NPK fertilizer controlled release produced by compression molding and fused deposition modeling

COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2022)

Related references

Note: Only part of the references are listed.

Review Nanoscience & Nanotechnology

Flax fiber-based polymer composites: a review

Aarti P. More

Summary: Flax fiber is a popular natural fiber used as a reinforcing agent for polymer composites. Surface treatment improves the adhesion between fiber and polymer, enhancing mechanical performance. Additionally, flax fiber composites are more environmentally friendly compared to petroleum-based composites.

ADVANCED COMPOSITES AND HYBRID MATERIALS (2022)

Add to Collection

Article Chemistry, Physical

Hedysarum coronarium-Based Green Composites Prepared by Compression Molding and Fused Deposition Modeling

Roberto Scaffaro et al.

Summary: An innovative green composite was produced by adding Hedysarum coronarium flour to a starch-based biodegradable polymer. The influence of filler content on processability, morphology, and mechanical properties of the composites was investigated. The results showed that FDM samples had higher mechanical properties compared to CM ones, and the filler effectively acted as reinforcement in the composites.

MATERIALS (2022)

Add to Collection

Article Nanoscience & Nanotechnology

Precise regulation of weakly negative permittivity in CaCu3Ti4O12 metacomposites by synergistic effects of carbon nanotubes and grapheme

Han Wu et al.

Summary: The study successfully achieved negative permittivity by preparing ternary percolation nanocomposites, investigating the synergy between graphene and carbon nanotubes, and controlling the formation of conductive paths to regulate negative permittivity precisely.

ADVANCED COMPOSITES AND HYBRID MATERIALS (2022)

Add to Collection

Article

Lignin/Si Hybrid Carbon Nanofibers towards Highly Efficient Sustainable Li-ion Anode Materials

Mario Culebras et al.

Engineered Science (2022)

Add to Collection

Article Materials Science, Ceramics

Biocompatibility and antibacterial behavior of electrochemically deposited Hydroxyapatite/ZnO porous nanocomposite on NiTi biomedical alloy

Alireza Mehrvarz et al.

CERAMICS INTERNATIONAL (2022)

Add to Collection

Article Engineering, Manufacturing

An innovative route to prepare in situ graded crosslinked PVA graphene electrospun mats for drug release

Emmanuel Fortunato Gulino et al.

Summary: We present a fast and one-step method to obtain PVA/graphene/chlorhexidine nanofibrous membranes with a crosslinking gradient. The crucial role of graphene in promoting heat transfer throughout the entire structure is revealed, leading to 70-80% crosslinking degrees and preventing delamination issues. The release behavior of the materials can be tuned from instantaneous/burst to sustained release (up to 500 h) by adjusting formulation and preparation technique.

COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2022)

Add to Collection

Article Polymer Science

Green Composites Based on Hedysarum coronarium with Outstanding FDM Printability and Mechanical Performance

Roberto Scaffaro et al.

Summary: The addition of natural scraps to biodegradable polymers has attracted attention as a way to reduce environmental pollution caused by traditional plastics. In this study, new composites were developed by adding Hedysarum coronarium flour to Poly (lactic acid), and their properties were characterized. Results showed that the addition of the filler effectively improved the performance of the polymer composites.

POLYMERS (2022)

Add to Collection

Article Chemistry, Applied

Waterborne acrylic resin co-modified by itaconic acid and γ-methacryloxypropyl triisopropoxidesilane for improved mechanical properties, thermal stability, and corrosion resistance

Zhuanghua Yu et al.

Summary: Waterborne acrylic resin modified with both IA and KH571 was successfully synthesized by seeded emulsion polymerization. The addition of IA and KH571 greatly improved the water resistance and other properties of the resin coating, making it a potential candidate for waterproof and anticorrosive coatings.

PROGRESS IN ORGANIC COATINGS (2022)

Add to Collection

Article Nanoscience & Nanotechnology

Mechanical and dynamic mechanical behavior of acetylation-treated plain woven banana reinforced biodegradable composites

S. B. Kivade et al.

Summary: The research demonstrated that acetylation treatment can improve the performance of PWBF, enhance the internal bonding of PWBF/PVA, reduce water absorption rate, and have an impact on biodegradability.

ADVANCED COMPOSITES AND HYBRID MATERIALS (2022)

Add to Collection

Article Engineering, Mechanical

Effect of infill pattern and infill density at varying part orientation on tensile properties of fused deposition modeling-printed poly-lactic acid part

Harshit K. Dave et al.

Summary: Fused deposition modeling is a widely used additive manufacturing process that can create samples with complex geometrical shapes. This study explored the significant impact of part orientation, infill pattern, and infill density on tensile strength. Results showed that parts printed with flat part orientation and concentric pattern exhibited maximum tensile strength, while increasing infill density also increased tensile strength.

PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART C-JOURNAL OF MECHANICAL ENGINEERING SCIENCE (2021)

Add to Collection

Review Chemistry, Multidisciplinary

Controlled release fertilizer: A review on developments, applications and potential in agriculture

Pravin Vejan et al.

Summary: CRF plays a crucial role in sustainable agriculture, but faces challenges in commercial practices such as high cost, low efficiency, and coatings mainly composed of synthetic polymers. However, using polymers derived from renewable and biodegradable sources as coating material for CRF has great potential.

JOURNAL OF CONTROLLED RELEASE (2021)

Add to Collection

Review Chemistry, Multidisciplinary

Fused Deposition Modeling (FDM), the new asset for the production of tailored medicines

Sylvain Cailleaux et al.

Summary: The shift towards precision medicine in conventional medicine has led to a focus on customizing oral drug delivery using 3D printing technology, particularly Fused Deposition Modeling (FDM). Various FDM methods have been reported in the production of pharmaceutical solid oral forms, with challenges such as high printing temperatures for thermosensitive ingredients and moisture sensitivity in storage studies. FDM appears to be well-suited for treating rare diseases and populations requiring tailored doses or release kinetics.

JOURNAL OF CONTROLLED RELEASE (2021)

Add to Collection

Article Agronomy

Biodegradable Polymer Compounds Reinforced with Banana Fiber for the Production of Protective Bags for Banana Fruits in the Context of Circular Economy

Pablo Bordon et al.

Summary: This study developed biodegradable bags reinforced with banana fiber to address the environmental impact of banana packaging waste. Through experimentation, the optimal manufacturing process and formulation were determined, enabling these biodegradable bags to perform well in field tests.

AGRONOMY-BASEL (2021)

Add to Collection

Review Pharmacology & Pharmacy

3D printing in personalized drug delivery: An overview of hot-melt extrusion-based fused deposition modeling

Nagireddy Dumpa et al.

Summary: Advancements in pharmaceutical technologies have led to the personalization of therapies over the last decade, with 3D printing emerging as a technique for manufacturing complex and customized dosage forms. Among the various 3D printing techniques, fused deposition modeling (FDM) is versatile and cost-effective, particularly in conjunction with hot-melt extrusion (HME) for filament preparation.

INTERNATIONAL JOURNAL OF PHARMACEUTICS (2021)

Add to Collection

Article Nanoscience & Nanotechnology

Lightweight Fe3C@Fe/C nanocomposites derived from wasted cornstalks with high-efficiency microwave absorption and ultrathin thickness

Guangyu Qi et al.

Summary: Carbon materials have great potential in producing microwave absorbers, with Fe3C@Fe/C composites obtained from wasted cornstalks showing excellent absorption capabilities. The credit for this lies in the impedance matching and attenuation properties of the composites, as well as the synergistic influence of dielectric and magnetic losses in the porous microstructure. A low-cost method using agricultural waste is proposed to reduce pollution caused by burning cornstalks.

ADVANCED COMPOSITES AND HYBRID MATERIALS (2021)

Add to Collection

Article Polymer Science

Green Composites Based on PLA and Agricultural or Marine Waste Prepared by FDM

Roberto Scaffaro et al.

Summary: The study demonstrated that adding lignocellulosic fillers from Opuntia ficus indica and Posidonia oceanica to PLA can reduce costs and promote environmental sustainability without compromising processing and mechanical performance. Additionally, the increase in surface hydrophilicity may positively impact the biodegradability of the materials after disposal.

POLYMERS (2021)

Add to Collection

Article Materials Science, Composites

Hydrolytic degradation of PLA/Posidonia Oceanica green composites: A simple model based on starting morpho-chemical properties

Roberto Scaffaro et al.

Summary: This study investigated the degradability of PLA-based biocomposites containing Posidonia Oceanica flour at different loading levels and aspect ratios. The results showed that the biocomposites degraded much faster than neat PLA, with the fillers playing a crucial role in enhancing degradation and providing pathways for solution penetration. A new model was proposed to predict the degradation pathways based on morphological and chemical features of the composites.

COMPOSITES SCIENCE AND TECHNOLOGY (2021)

Add to Collection

Article Chemistry, Multidisciplinary

Biodegradable green composites: It's never too late to mend

Kiana Rafiee et al.

Summary: Biocomposites, made up of polymeric matrix and reinforcing fibers, have emerged as innovative materials and alternatives to traditional composites. To be classified as green and sustainable, biocomposites must align with green chemistry principles. This review discusses recent advancements in biocomposite development, addressing sourcing, synthesis, modification methods, and end-of-life options such as biodegradation and recyclability. Case studies focusing on poly(lactic) acid- and mycelium-based biocomposites are presented to further explore these aspects.

CURRENT OPINION IN GREEN AND SUSTAINABLE CHEMISTRY (2021)

Add to Collection

Article Agriculture, Multidisciplinary

Biodegradable Polymer Nanocomposites Provide Effective Delivery and Reduce Phosphorus Loss during Plant Growth

Leslie R. Sigmon et al.

Summary: This study synthesized biodegradable polymer nanocomposites that effectively released phosphorus and improved plant growth, reducing phosphorus loss by over 80% and having significant implications for the environment.

ACS AGRICULTURAL SCIENCE & TECHNOLOGY (2021)

Add to Collection

Review Polymer Science

Current State and Challenges of Natural Fibre-Reinforced Polymer Composites as Feeder in FDM-Based 3D Printing

Nishata Royan Rajendran Royan et al.

Summary: The review focuses on the current approaches of using NFRC as a feeder for AM, including fiber treatments, composite preparation methods, and addition of compatibilizer agents. The mechanical properties of printed parts are dependent on printing parameters, with the best parameters reported by other researchers being identified. The use of optimization techniques for NFRCs and potential research gaps in this field are also discussed.

POLYMERS (2021)

Add to Collection

Article Nanoscience & Nanotechnology

Hierarchically porous Co/C nanocomposites for ultralight high-performance microwave absorption

Peitao Xie et al.

Summary: This study prepared Co/C nanocomposites with Co nanoparticles uniformly distributed in amorphous carbon sheets, achieving excellent absorption performance through hierarchical porous microstructures. Excellent absorption performance was achieved at 10% and 15% Co/C content levels, providing a new pathway for designing ultralight absorbers.

ADVANCED COMPOSITES AND HYBRID MATERIALS (2021)

Add to Collection

Article Nanoscience & Nanotechnology

Pretreatment of hydroxy-terminated polybutadiene (HTPB)/toluene diisocyanate (TDI) binder system for biodegradation

Kai Wu et al.

Summary: A two-step pretreatment with depolymerization and epoxidation can reduce the molecular weight of the substrate, improve its hydrophilicity, and enhance its biodegradability compared to the HTPB/TDI binder system.

ADVANCED COMPOSITES AND HYBRID MATERIALS (2021)

Add to Collection

Review Materials Science, Multidisciplinary

A review of natural fiber composites: properties, modification and processing techniques, characterization, applications

Aliakbar Gholampour et al.

JOURNAL OF MATERIALS SCIENCE (2020)

Add to Collection

Article Materials Science, Paper & Wood

Spray-dried chitosan/nanocellulose microparticles: synergistic effects for the sustained release of NPK fertilizer

Lucas Luiz Messa et al.

CELLULOSE (2020)

Add to Collection

Article Polymer Science

A comprehensive evaluation of flexible FDM/FFF 3D printing filament as a potential material in medical application

Agnieszka Harynska et al.

EUROPEAN POLYMER JOURNAL (2020)

Add to Collection

Article Polymer Science

Green composites based on Atriplex halimus fibers and PLA matrix

Hayet Latifa Boudjema et al.

JOURNAL OF POLYMER ENGINEERING (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Effect of pore morphology and surface roughness on wettability of porous titania films

Bangyun Xiong et al.

MATERIALS RESEARCH EXPRESS (2020)

Add to Collection

Article Nanoscience & Nanotechnology

Investigation of biodegradable hybrid composites: effect of fibers on tribo-mechanical characteristics

B. Vinod et al.

ADVANCED COMPOSITES AND HYBRID MATERIALS (2020)

Add to Collection

Article Nanoscience & Nanotechnology

Study on the effects of fibre volume percentage on banana-reinforced epoxy composite by finite element method

Upendra Sharan Gupta et al.

ADVANCED COMPOSITES AND HYBRID MATERIALS (2020)

Add to Collection

Article Nanoscience & Nanotechnology

Structural and dielectric characterization of (PVP/PEO)/Al2O3 nanocomposites for biodegradable nanodielectric applications

Priyanka Dhatarwal et al.

ADVANCED COMPOSITES AND HYBRID MATERIALS (2020)

Add to Collection

Article Nanoscience & Nanotechnology

Synthesis and characterization of biodegradable AZ31/calcium phosphate glass composites for orthopedic applications

Sahar Mokhtari et al.

ADVANCED COMPOSITES AND HYBRID MATERIALS (2020)

Add to Collection

Article Pharmacology & Pharmacy

Application of 3D printing technology and quality by design approach for development of age-appropriate pediatric formulation of baclofen

Siddhant Palekar et al.

INTERNATIONAL JOURNAL OF PHARMACEUTICS (2019)

Add to Collection

Article Environmental Sciences

Thermo and pH-responsive methylcellulose and hydroxypropyl methylcellulose hydrogels containing K2SO4 for water retention and a controlled-release water-soluble fertilizer

Yi-Chun Chen et al.

SCIENCE OF THE TOTAL ENVIRONMENT (2019)

Add to Collection

Article Multidisciplinary Sciences

Targeted Double Negative Properties in Silver/Silica Random Metamaterials by Precise Control of Microstructures

Peitao Xie et al.

Research (2019)

Add to Collection

Article Engineering, Multidisciplinary

Structure-property relationship of PLA-Opuntia Ficus Indica biocomposites

Roberto Scaffaro et al.

COMPOSITES PART B-ENGINEERING (2019)

Add to Collection

Article Engineering, Environmental

PHB and Montmorillonite Clay Composites as KNO3 and NPK Support for a Controlled Release

Josiane Lima Souza et al.

JOURNAL OF POLYMERS AND THE ENVIRONMENT (2019)

Add to Collection

Review Polymer Science

FDM 3D Printing of Polymers Containing Natural Fillers: A Review of their Mechanical Properties

Valentina Mazzanti et al.

POLYMERS (2019)

Add to Collection

Article Materials Science, Multidisciplinary

Mechanical characteristics of wood, ceramic, metal and carbon fiber-based PLA composites fabricated by FDM

Zhaobing Liu et al.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2019)

Add to Collection

Article Pharmacology & Pharmacy

Interpreting non-linear drug diffusion data: Utilizing Korsmeyer-Peppas model to study drug release from liposomes

Iren Yeeling Wu et al.

EUROPEAN JOURNAL OF PHARMACEUTICAL SCIENCES (2019)

Add to Collection

Proceedings Paper Engineering, Mechanical

Wettability of 3 D Printed Polylactic Acid (PLA) Parts

Ujjaval Modi et al.

1ST INTERNATIONAL CONFERENCE ON ADVANCES IN MECHANICAL ENGINEERING AND NANOTECHNOLOGY (ICAMEN 2019) (2019)

Add to Collection

Article Chemistry, Applied

Ethylcellulose as a coating material in controlled-release fertilizers

Krzysztof Lubkowski et al.

POLISH JOURNAL OF CHEMICAL TECHNOLOGY (2019)

Add to Collection

Article Polymer Science

Controlled release fertilizer encapsulated by a κ-carrageenan hydrogel

Gladys Rozo et al.

POLIMEROS-CIENCIA E TECNOLOGIA (2019)

Add to Collection

Article Polymer Science

Preparation and characterization of a superabsorbent slow-release fertilizer with sodium alginate and biochar

M. Baki et al.

JOURNAL OF APPLIED POLYMER SCIENCE (2018)

Add to Collection

Article Engineering, Environmental

Green Composite Based on PHB and Montmorillonite for KNO3 and NPK Delivery System

Josiane de Lima Souza et al.

JOURNAL OF POLYMERS AND THE ENVIRONMENT (2018)

Add to Collection

Article Engineering, Manufacturing

Physical properties of green composites based on poly-lactic acid or MaterBi (R) filled with Posidonia Oceanica leaves

Roberto Scaffaro et al.

COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2018)

Add to Collection

Article Engineering, Multidisciplinary

PLA based biocomposites reinforced with Posidonia oceanica leaves

Roberto Scaffaro et al.

COMPOSITES PART B-ENGINEERING (2018)

Add to Collection

Article Biochemistry & Molecular Biology

Potential of lignocellulosic fractions from Posidonia oceanica to improve barrier and mechanical properties of bio-based packaging materials

Isaac Benito-Gonzalez et al.

INTERNATIONAL JOURNAL OF BIOLOGICAL MACROMOLECULES (2018)

Add to Collection

Article Materials Science, Biomaterials

Slow-release NPK fertilizer encapsulated by carboxymethyl cellulose-based nanocomposite with the function of water retention in soil

Ali Olad et al.

MATERIALS SCIENCE & ENGINEERING C-MATERIALS FOR BIOLOGICAL APPLICATIONS (2018)

Add to Collection

Article Pharmacology & Pharmacy

Development of modified release 3D printed tablets (printlets) with pharmaceutical excipients using additive manufacturing

Alvaro Goyanes et al.

INTERNATIONAL JOURNAL OF PHARMACEUTICS (2017)

Add to Collection

Article Engineering, Mechanical

Tensile strength of partially filled FFF printed parts: experimental results

Shahrain Mahmood et al.

RAPID PROTOTYPING JOURNAL (2017)

Add to Collection

Article Pharmacology & Pharmacy

An investigation into the use of polymer blends to improve the printability of and regulate drug release from pharmaceutical solid dispersions prepared via fused deposition modeling (FDM) 3D printing

Muqdad Alhijjaj et al.

EUROPEAN JOURNAL OF PHARMACEUTICS AND BIOPHARMACEUTICS (2016)

Add to Collection

Article Engineering, Multidisciplinary

Investigating the influence of infill percentage on the mechanical properties of fused deposition modelled ABS parts

Kenny L. Alvarez C et al.

INGENIERIA E INVESTIGACION (2016)

Add to Collection

Article Engineering, Multidisciplinary

Investigating the influence of infill percentage on the mechanical properties of fused deposition modelled ABS parts

Kenny L. Alvarez C et al.

INGENIERIA E INVESTIGACION (2016)

Add to Collection

Article Materials Science, Multidisciplinary

3D printing of wood fibre biocomposites: From mechanical to actuation functionality

A. Le Duigou et al.

MATERIALS & DESIGN (2016)

Add to Collection

Article Engineering, Manufacturing

Experimental Investigations of Process Parameters Influence on Rheological Behavior and Dynamic Mechanical Properties of FDM Manufactured Parts

Omar Ahmed Mohamed et al.

MATERIALS AND MANUFACTURING PROCESSES (2016)

Add to Collection

Article Pharmacology & Pharmacy

Effect of geometry on drug release from 3D printed tablets

Alvaro Goyanes et al.

INTERNATIONAL JOURNAL OF PHARMACEUTICS (2015)

Add to Collection

Article Medicine, Research & Experimental

3D Printing of Medicines: Engineering Novel Oral Devices with Unique Design and Drug Release Characteristics

Alvaro Goyanes et al.

MOLECULAR PHARMACEUTICS (2015)

Add to Collection

Article Polymer Science

Multilayer-Coated NPK Compound Fertilizer Hydrogel with Controlled Nutrient Release and Water Absorbency

Supaporn Noppakundilograt et al.

JOURNAL OF APPLIED POLYMER SCIENCE (2015)

Add to Collection

Article Polymer Science

Biodegradation paths of Mater-Bi®/kenaf biodegradable composites

Giada Lo Re et al.

JOURNAL OF APPLIED POLYMER SCIENCE (2013)

Add to Collection

Article Engineering, Environmental

A Comparative Study Between Bio-composites Obtained with Opuntia ficus indica Cladodes and Flax Fibers

A. Greco et al.

JOURNAL OF POLYMERS AND THE ENVIRONMENT (2013)

Add to Collection

Article Polymer Science

Degradation of Mater-Bi®/wood flour biocomposites in active sewage sludge

R. Scaffaro et al.

POLYMER DEGRADATION AND STABILITY (2009)

Add to Collection

Article Engineering, Manufacturing

Mechanical behaviour of Mater-Bi®/wood flour composites: A statistical approach

M. Morreale et al.

COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2008)

Add to Collection

Article Agriculture, Multidisciplinary

Controlled-release NPK fertilizer encapsulated by polymeric membranes

A Jarosiewicz et al.

JOURNAL OF AGRICULTURAL AND FOOD CHEMISTRY (2003)

Add to Collection

Review Pharmacology & Pharmacy

Modeling and comparison of dissolution profiles

P Costa et al.

EUROPEAN JOURNAL OF PHARMACEUTICAL SCIENCES (2001)

Add to Collection

© Peeref 2019-2024. All rights reserved.