☆ 4.5 Article

Constitutive Model and Fracture Criterion of Q345 Steel Welded Joints

COMPLEXITY (2022)

Related references

Note: Only part of the references are listed.

Article Construction & Building Technology

Ultimate strain models derived using a Digital Image Correlation (DIC) system for preloaded RC columns subjected to heating and cooling and confined with CFRP sheets

Yaman Sami Shareef Al-Kamaki

Summary: This study established strain models to estimate the strains of undamaged or damaged columns due to heat exposure and subsequent wrapping with CFRP sheets. The developed models offer better prediction of experimental performance compared to existing models, especially for preloaded columns exposed to heating-cooling and retrofitted with CFRP fabrics.

JOURNAL OF BUILDING ENGINEERING (2021)

Add to Collection

Article Engineering, Mechanical

Failure Strain and Fracture Prediction During Shock Tube Impact Forming of AA 5052-H32 Sheet

Saibal Kanchan Barik et al.

Summary: This study focused on evaluating failure strain and fracture pattern during shock tube impact forming of 1.5 mm thick AA 5052-H32 sheet through numerical and experimental methods. The modified Johnson-Cook model showed better flow stress predictability, and combining Cockcroft-Latham, Brozzo, and Freudenthal failure models with Johnson-Cook and modified Johnson-Cook flow stress models led to fair agreement with experimental data in predicting failure strain and necking location.

JOURNAL OF ENGINEERING MATERIALS AND TECHNOLOGY-TRANSACTIONS OF THE ASME (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Effects of Stress Amplitude Ratio and Phase Angle on Short Fatigue Crack Behavior and Fracture Mode of EA4T Steel

Zhen Liao et al.

Summary: The study found that the same short fatigue crack behavior was observed in all specimens with homogeneous and fine microstructure, regardless of the loading condition. The fracture morphology showed cracks initiated on the specimen surface, with distinct specific fracture morphology in each region. The comparison and analysis of fatigue life and short crack growth rate indicated that stress amplitude ratio and phase angle significantly influenced the fatigue life and short crack growth rate of the specimens.

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2021)

Add to Collection

Article Engineering, Mechanical

Fracture parameters calibration and validation for the high strength steel based on the mesoscale failure index

Haohui Xin et al.

Summary: This study discusses how to accurately obtain material parameters for ductile fracture simulation in high strength steel structures, proposing a method that combines micromechanics with the phenomenological fracture model. By using mesoscale critical equivalent plastic strain as a failure index, the fracture locus of the uncoupled phenomenological model can be calibrated, leading to more accurate material parameters.

THEORETICAL AND APPLIED FRACTURE MECHANICS (2021)

Add to Collection

Article Engineering, Multidisciplinary

3D-DIC strain field measurements in bolted and hybrid bolted-bonded joints of woven carbon-epoxy composites

Masoud Mehrabian et al.

Summary: In this study, the 3D digital image correlation technique was used to study the tensile behaviors of single-lap bolted and hybrid bolted-bonded joints. The results show that hybridization can mitigate stress concentration around bolts, delay damage initiation, reduce secondary bending and twisting, and improve strength retention, while maintaining a balance between bypass and bearing loads in multi-bolt fastened joints.

COMPOSITES PART B-ENGINEERING (2021)

Add to Collection

Article Construction & Building Technology

A new constitutive model for high strength structural steels

Yuan-Zuo Wang et al.

Summary: This paper presents an experimental study on High Strength Structural (HSS) steels, identifying existing constitutive models' limitations in capturing the yield plateau region and full-range softening behavior under cyclic loading. A new constitutive model, the HSS-TD model, with consideration of three-stage strength softening, shows significantly lower errors compared to the conventional A-F model. The limitations of the HSS-TD model, including the influence of strain history and nonproportional loading, are also discussed.

JOURNAL OF CONSTRUCTIONAL STEEL RESEARCH (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Aspects of ductile failure prediction of interstitial-free steel based on a Gurson-type damage modelAspekte der Vorhersage des duktilen Versagens von interstitialfreiem Stahl auf der Grundlage eines Schadigungsmodells vom Gurson-Typ

C. Z. Bressan et al.

MATERIALWISSENSCHAFT UND WERKSTOFFTECHNIK (2020)

Add to Collection

Article Construction & Building Technology

Extremely - low cycle fatigue fracture of Q235 steel at different stress triaxialities

Zeshen Li et al.

JOURNAL OF CONSTRUCTIONAL STEEL RESEARCH (2020)

Add to Collection

Article Mechanics

Modeling anisotropic ductile fracture behavior of Ti-6Al-4V titanium alloy for sheet forming applications at room temperature

Bingtao Tang et al.

INTERNATIONAL JOURNAL OF SOLIDS AND STRUCTURES (2020)

Add to Collection

Article Engineering, Multidisciplinary

An in-situ self-calibration method for non-contact full-field strain measurement

Huaxia Deng et al.

MEASUREMENT (2020)

Add to Collection

Article Chemistry, Physical

Plasticity of Bead-on-Plate Welds Made with the Use of Stored Flux-Cored Wires for Offshore Applications

Aleksandra Swierczynska et al.

MATERIALS (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Optimization of microstructural and mechanical properties of friction stir welded A356 pipes using Taguchi method

Mostafa Akbari et al.

MATERIALS RESEARCH EXPRESS (2019)

Add to Collection

Article Computer Science, Interdisciplinary Applications

Model-based estimation of the stress-strain curve of metal strips

G. Stadler et al.

MATHEMATICAL AND COMPUTER MODELLING OF DYNAMICAL SYSTEMS (2019)

Add to Collection

Article Materials Science, Multidisciplinary

Formation of thermo-mechanically affected zone in friction stir welding

Parisa Zolghadr et al.

MATERIALS RESEARCH EXPRESS (2019)

Add to Collection

Article Materials Science, Multidisciplinary

EFFECT OF STORAGE CONDITIONS OF RUTILE FLUX CORED WELDING WIRES ON PROPERTIES OF WELDS

A. Swierczynska

ADVANCES IN MATERIALS SCIENCE (2019)

Add to Collection

Proceedings Paper Engineering, Mechanical

Applied problems of fracture mechanics, resource and safety of technical systems

V. Moskvichev

ECF22 - LOADING AND ENVIRONMENTAL EFFECTS ON STRUCTURAL INTEGRITY (2018)

Add to Collection

Article Engineering, Mechanical

A method to investigate strain rate effects on necking and fracture behaviors of advanced high-strength steels using digital imaging strain analysis

Kentaro Sato et al.

INTERNATIONAL JOURNAL OF IMPACT ENGINEERING (2015)

Add to Collection

Article Construction & Building Technology

Ductile fracture model for structural steel under cyclic large strain loading

Liang-Jiu Jia et al.

JOURNAL OF CONSTRUCTIONAL STEEL RESEARCH (2015)

Add to Collection

Article Engineering, Mechanical

On fracture locus in the equivalent strain and stress triaxiality space

YB Bao et al.

INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2004)

Add to Collection

Article Engineering, Industrial

Determination of true stress-strain-curves and normal anisotropy in tensile tests with optical strain measurement

H Hoffmann et al.

CIRP ANNALS-MANUFACTURING TECHNOLOGY (2003)

Add to Collection

© Peeref 2019-2024. All rights reserved.