☆ 4.7 Article

Microstructure, mechanical and anti-ablation properties of Mg-modified C/ C-ZrC-SiC composites prepared by sol-gel technology

CERAMICS INTERNATIONAL (2022)

Related references

Note: Only part of the references are listed.

Article Materials Science, Ceramics

Effect of MgCl2 addition on the preparation of ZrC-SiC composite particles by sol-gel

Lei Zheng et al.

Summary: The study focused on synthesizing high purity ZrC-SiC powders by combining a sol-gel process with carbothermal reduction and adding MgCl2 at a lower temperature. By optimizing fabrication conditions and synthesis temperature, the formation of ZrC-SiC powders was accelerated at lower temperatures, achieving stoichiometric carbon content.

CERAMICS INTERNATIONAL (2022)

Add to Collection

Review Materials Science, Multidisciplinary

Micro/nano multiscale reinforcing strategies toward extreme high-temperature applications: Take carbon/carbon composites and their coatings as the examples

Qiangang Fu et al.

Summary: Carbon fiber reinforced carbon composites (C/Cs) are promising high-temperature materials, but they are prone to destructive oxidation at elevated temperatures. Matrix modification and coating technologies are not sufficient due to brittleness of ceramics and other inherent issues. Micro/nano multiscale reinforcing strategies have been developed in the past two decades to fabricate C/Cs with high strength and excellent high-temperature stability.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2022)

Add to Collection

Article Materials Science, Ceramics

Ablation resistant ZrC coating modified by polymer-derived SiC/TiC nanocomposites for ultra-high temperature application

Yuyu Zhang et al.

Summary: In order to enhance the ablation resistance of ZrC coating on SiC-coated carbon/carbon composites above 2000 degrees C, SiC/TiC nanocomposites were incorporated into the ZrC coating via supersonic atmospheric plasma spraying (SAPS), resulting in the formation of ZrC-SiC/TiC-NCs coating. The good ablation resistance of the coating is mainly attributed to the distinctive capsule-like multi-crystalline microstructure of SiC/TiC-NCs, which helps in the formation of a high viscosity and low evaporation pressure Zr-Ti-Si-O glass during ablation.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2022)

Add to Collection

Article Materials Science, Ceramics

Effect of the Y2O3 amount on the oxidation behavior of ZrB2-SiC-based coatings for carbon/carbon composites

Hao Lin et al.

Summary: This study investigates the effect of Y2O3 addition on the oxidation resistance of ZrB2-SiC-Y2O3 coating on SiC coated carbon/carbon composites. The results show that adding Y2O3 greatly enhances the oxidation-resistant properties of the coating, leading to the formation of a dense structure and yttria stabilized zirconia, Y2Si2O7, t-ZrO2 phases. The improved oxidation resistance is attributed to the formation of a Zr-Si-Y-O glass barrier layer, reduced m-ZrO2 content, and the presence of Y2Si2O7 as a pinning phase.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Ablation behavior under oxyacetylene torch of ZrC coating modified by SiC/TaC nanocomposites

Yuyu Zhang et al.

Summary: In this study, a plasma-sprayed ZrC coating modified by a polymer-derived SiC/TaC nanocomposite was applied on SiC-coated carbon/carbon composites. The results showed that the SiC/TaC modified coating exhibited improved stability and ablation resistance, as well as the formation of a dense protective layer.

CORROSION SCIENCE (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Ablation behaviour and mechanism of Mg-modified ZrC-SiC composite in plasma ablation flame

Lei Zheng et al.

Summary: In this study, a fully dense Mg-modified ZrC-SiC composite was prepared and its microstructure, phase evolution, and ablation behavior were investigated. The results showed that the introduction of Mg significantly improved the ablation resistance and the integrity of the oxide layer.

CORROSION SCIENCE (2022)

Add to Collection

Article Materials Science, Ceramics

High temperature oxidation resistance of Y2O3 modified ZrB2-SiC coating for carbon/carbon composites

Hanchun Ma et al.

Summary: Y2O3 modified ZrB2-SiC coatings fabricated on C/C composites by atmospheric plasma spraying demonstrated excellent oxidation resistance and thermal stability at high temperatures. The presence of Y2O3 effectively inhibited the phase transition of ZrO2, preventing cracks caused by volume expansion of the coating. The ceramic phases Y2SiO5, Y2Si2O7, and ZrSiO4 reduced the volatilization of SiO2, contributing to the overall protective performance of the coatings.

CERAMICS INTERNATIONAL (2021)

Add to Collection

Article Materials Science, Ceramics

Improving the sinterability of ZrC-SiC composite powders by Mg addition

Lei Zheng et al.

Summary: In this study, core-shell-structured hybrid ZrC-SiC composite nanoparticles were successfully synthesized by adding Mg, which enhanced the sinterability of the ZrC-SiC nanoparticles. The addition of MgCl2 not only strengthened the network structure of ZrC-SiC gel, but also led to the formation of an amorphous Mg-Si-O oxide coating on the nanoparticle surfaces, enhancing the sinterability of the ZrC-SiC nanoparticles.

CERAMICS INTERNATIONAL (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Effects of PyC shell thickness on the microstructure, ablation resistance of SiCnws/PyC-C/C-ZrC-SiC composites

Qinchuan He et al.

Summary: By increasing the PyC shell thickness in SiC nanowires/pyrocarbon core-shell structured composites, the density and thermal conductivity of the composites can be improved while reducing the coefficient of thermal expansion, ultimately enhancing the anti-ablation properties. However, there is an optimal PyC thickness where further increases can lead to an increase in ablation rates.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2021)

Add to Collection

Article Materials Science, Ceramics

The effect of carbon source addition order during sol-gel process on the properties of C/C-ZrC-SiC composites

Chen Zeng et al.

Summary: Optimizing the addition order of carbon source during sol-gel process can greatly improve the properties of C/C-ZrC-SiC composites, including microstructure, mechanical property, and ablation resistance. The excellent performance is attributed to little erosion of carbon fibers and the dense matrix of ZrC-SiC ceramics obtained from adding carbon source before gelation.

CERAMICS INTERNATIONAL (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Ablation behavior and mechanisms of 3D Cf/ZrB2-SiC composite applied in long-term temperature up to 2400 °C

Dongyang Zhang et al.

Summary: 3D C-f/ZrB2-SiC composites with homogeneous architecture were prepared via vibration-assisted slurry impregnation combined with precursor infiltration and pyrolysis to evaluate the long-term ablation behavior of carbon fiber reinforced ultra-high temperature ceramics. The intact structure of the sample was maintained after ablation due to the formation of triple oxide layers, resulting in superior ablation resistance with specific linear and mass ablation rates.

CORROSION SCIENCE (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructure and ablation behavior of Zr-Ti-Si-C multiphase coating fabricated by solid solution and in-situ reaction

Anhong Shi et al.

Summary: Zr-Ti-Si-C solid solution coatings were fabricated by solid solution and in-situ reaction methods, and the effects of TiC on microstructure, phase evolution, and ablation behavior were investigated. The solid solution structure reduced the active oxidation of Si source, enhanced ablative properties of the coatings.

CORROSION SCIENCE (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Evaluation of oxidation resistant SiC-ZrB2 composite interlayer for plasma sprayed Y2O3 coating over graphite

B. Madhura et al.

Summary: The SiC-ZrB2 composite interlayer coating developed on high density graphite enhances the durability of the Y2O3 topcoat and provides passive oxidation protection, significantly extending its lifespan under high temperature conditions.

CORROSION SCIENCE (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Influence of MgO addition on mechanical and ablation characteristics of ZrB2-SiC composites developed through microwave sintering

Ankur Sharma et al.

Summary: The addition of MgO to ZrB2-SiC composites can reduce sintering temperature, enhance fracture toughness, and improve ablation resistance. Composites containing 2 vol% MgO exhibit the optimal performance in terms of relative density, microhardness, fracture toughness, and ablation resistance.

JOURNAL OF MATERIALS SCIENCE (2021)

Add to Collection

Article Materials Science, Coatings & Films

Ablative Property and Mechanism of ZrC-TaC/ZrC-SiC Coatings on C/C Composites under Different Heat Fluxes

Xiao Luo et al.

Summary: The study demonstrates that in high-temperature aerobic environment, the ZrC-TaC/ZrC-SiC coating system can effectively protect carbon materials from oxidation and improve ablation resistance. However, at lower heat flux, inadequate chemical combination between the layers can result in reduced overall resistance to ablation.

JOURNAL OF THERMAL SPRAY TECHNOLOGY (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Comparative insights into C/C-ZrC-SiC composites with different substrate carbon on microstructures, mechanical properties, and ablation behaviors

Zheng Peng et al.

Summary: The study systematically researched the microstructures, mechanical properties, and ablation behaviors of C/C-ZrC-SiC composites fabricated using different carbon substrates, finding that C/PyC-ZrC-SiC composites had higher flexural strength while C/RdC-ZrC-SiC composites exhibited better ablation resistance after exposure to oxyacetylene ablation.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Mechanical, oxidation and ablation properties of C/(C-SiC)CVI-(ZrC-SiC)PIP composites

Jinjin Yao et al.

CORROSION SCIENCE (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Effects of ZrC/SiC ratios on mechanical and ablation behavior of C/C-ZrC-SiC composites prepared by carbothermal reaction of hydrothermal co-deposited oxides

Haibo Ouyang et al.

CORROSION SCIENCE (2020)

Add to Collection

Review Materials Science, Multidisciplinary

Selection, processing, properties and applications of ultra-high temperature ceramic matrix composites, UHTCMCs - a review

Jon Binner et al.

INTERNATIONAL MATERIALS REVIEWS (2020)

Add to Collection

Article Materials Science, Ceramics

Effects of LaB6 on the microstructures and ablation properties of 3D C/C-SiC-ZrB2-LaB6 composites

Cunqian Fang et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2020)

Add to Collection

Article Materials Science, Ceramics

Ultra-high-temperature ablation behavior of SiC-ZrC-TiC modified carbon/carbon composites fabricated via reactive melt infiltration

Yi Zeng et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2020)

Add to Collection

Article Materials Science, Ceramics

Effect of ZrC particle distribution on the ablation resistance of C/C-SiC-ZrC composites fabricated using precursor infiltration pyrolysis

Xiaowei Wu et al.

CERAMICS INTERNATIONAL (2020)

Add to Collection

Article Materials Science, Ceramics

Enhanced mechanical properties and thermal shock resistance of Cf/ZrB2-SiC composite via an efficient slurry injection combined with vibration-assisted vacuum infiltration

Dongyang Zhang et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2020)

Add to Collection

Article Materials Science, Ceramics

Oxidation behaviors of MgO-C refractories with different Si/SiC ratio in the 1100-1500 °C range

Junli Xiao et al.

CERAMICS INTERNATIONAL (2019)

Add to Collection

Article Materials Science, Ceramics

Effect of the Al2O3 additive on the high temperature ablation behavior of the ZrC-ZrO2 coating for SiC-coated carbon/carbon composites

Caixia Huo et al.

CERAMICS INTERNATIONAL (2019)

Add to Collection

Article Materials Science, Ceramics

Microstructure and ablation properties of La2O3 modified C/C-SiC composites prepared via precursor infiltration pyrolysis

Cunqian Fang et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2019)

Add to Collection

Article Materials Science, Ceramics

Thermal cycling resistance of ZrB2-SiC coatings with MgO additive on SiC coated graphite

Changling Zhou et al.

CERAMICS INTERNATIONAL (2018)

Add to Collection

Article Materials Science, Ceramics

Fabrication and performance of micro-diamond modified C/SiC composites via precursor impregnation and pyrolysis process

Lei Chen et al.

CERAMICS INTERNATIONAL (2018)

Add to Collection

Article Materials Science, Ceramics

Viscosity of glass-forming systems

Qiuju Zheng et al.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2017)

Add to Collection

Article Materials Science, Ceramics

Vaporization coefficients of SiO2 and MgO

Nathan Jacobson et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2017)

Add to Collection

Article Materials Science, Ceramics

Microstructure and ablation mechanism of C/C-ZrC-SiC composites in a plasma flame

Shaolei Wang et al.

CERAMICS INTERNATIONAL (2017)

Add to Collection

Article Materials Science, Ceramics

Effects of oxidizing species on ablation behavior of C/C-ZrB2-ZrC-SiC composites prepared by precursor infiltration and pyrolysis

Xin Yang et al.

CERAMICS INTERNATIONAL (2016)

Add to Collection

Article Materials Science, Multidisciplinary

Effects of high-temperature annealing on the microstructures and mechanical properties of C/C-ZrC-SiC composites prepared by precursor infiltration and pyrolysis

Chunhong Ma et al.

MATERIALS & DESIGN (2016)

Add to Collection

Article Materials Science, Multidisciplinary

Ablation mechanism of C/C-ZrB2-ZrC-SiC composite fabricated by polymer infiltration and pyrolysis with preform of Cf/ZrB2

Dong Huang et al.

CORROSION SCIENCE (2015)

Add to Collection

Article Materials Science, Multidisciplinary

Effect of SiC/ZrC ratio on the mechanical and ablation properties of C/C-SiC-ZrC composites

Bo Feng et al.

CORROSION SCIENCE (2014)

Add to Collection

Article Nanoscience & Nanotechnology

Fabrication and properties of PIP 3D Cf/ZrC-SiC composites

Chunlei Yan et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2014)

Add to Collection

Article Nanoscience & Nanotechnology

Mechanical and dielectric properties of 2.5D SiCf/SiC-Al2O3 composites prepared via precursor infiltration and pyrolysis

Yang Mu et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2014)

Add to Collection

Article Chemistry, Applied

Synthesis and pyrolysis of a novel preceramic polymer PZMS from PMS to fabricate high-temperature-resistant ZrC/SiC ceramic composite

Hao Wang et al.

APPLIED ORGANOMETALLIC CHEMISTRY (2013)

Add to Collection

Article Chemistry, Physical

Effects of porous C/C density on the densification behavior and ablation property of C/C-ZrC-SiC composites

Ke-zhi Li et al.

CARBON (2013)

Add to Collection

Article Materials Science, Multidisciplinary

Mechanism of ablation of 3D C/ZrC-SiC composite under an oxyacetylene flame

Si'an Chen et al.

CORROSION SCIENCE (2013)

Add to Collection

Article Geosciences, Multidisciplinary

First principles viscosity and derived models for MgO-SiO2 melt system at high temperature

Bijaya B. Karki et al.

GEOPHYSICAL RESEARCH LETTERS (2013)

Add to Collection

Article Materials Science, Multidisciplinary

Nanosize stabilization of cubic and tetragonal phases in reactive plasma synthesized zirconia powders

S. Jayakumar et al.

MATERIALS CHEMISTRY AND PHYSICS (2013)

Add to Collection

Article Materials Science, Ceramics

Microstructure and ablation behaviors of integer felt reinforced C/C-SiC-ZrC composites prepared by a two-step method

Zhaoqian Li et al.

CERAMICS INTERNATIONAL (2012)

Add to Collection

Article Materials Science, Multidisciplinary

A simple way to prepare precursors for zirconium carbide

Dan Zhao et al.

JOURNAL OF MATERIALS SCIENCE (2010)

Add to Collection

Article Materials Science, Ceramics

Fabrication and Properties of Cf/SiC-ZrC Composites

Zhen Wang et al.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2008)

Add to Collection

Article Nanoscience & Nanotechnology

Effect of SiC particle dispersion on microstructure and mechanical properties of polymer-derived SiC/SiC composite

M Kotani et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2003)

Add to Collection

Article Materials Science, Multidisciplinary

Chemical synthesis of nanocrystals of tantalum ion-doped tetragonal zirconia

JC Ray et al.

MATERIALS LETTERS (2002)

Add to Collection

Article Crystallography

Thermodynamic analysis of molecular beam epitaxy of MgO(s) I. MgO vaporization by electron bombardment

JL Vassent et al.

JOURNAL OF CRYSTAL GROWTH (2000)

Add to Collection

© Peeref 2019-2024. All rights reserved.