4.7 Review

Sustainable utilization of red mud waste (bauxite residue) and slag for the production of geopolymer composites: A review

Related references

Note: Only part of the references are listed.
Article Construction & Building Technology

Development and use of geopolymers for energy conversion: An overview

Eric Enrique Sanchez Diaz et al.

Summary: This study revises the use of geopolymers for energy conversion, with a focus on their conductive properties, Seebeck effect, and piezoelectric effect. It discusses the effects of materials like TiO2 and carbon-based materials, as well as alkaline activator concentrations, on geopolymers. The research emphasizes the piezoelectric effects on geopolymers when incorporating graphene and TiO2 as fillers, showcasing their potential in solar, thermal, and mechanical energy conversion.

CONSTRUCTION AND BUILDING MATERIALS (2022)

Article Construction & Building Technology

Correlating the amorphous phase structure of vitrified bauxite residue (red mud) to the initial reactivity in binder systems

Tobias Hertel et al.

Summary: The initial reactivity of slags produced using bauxite residue as the main raw material in cementitious systems was assessed. The study found a correlation between the structure of the slag's amorphous phase and reaction kinetics.

CEMENT & CONCRETE COMPOSITES (2022)

Article Chemistry, Applied

Acid-pretreated red mud for selective catalytic reduction of NOx with NH3: Insights into inhibition mechanism of binders

Bin Wang et al.

Summary: In this study, shaped RM catalysts were prepared using sesbania powder, guar gum, and carboxymethylcellulose sodium as binders, with sesbania powder showing the highest activity. The use of RM catalyst was found to be cost-effective and could alleviate the issue of RM accumulation.

CATALYSIS TODAY (2021)

Article Engineering, Chemical

Investigation on the fabrication of lightweight aggregate with acid-leaching tailings of vanadium-bearing stone coal minerals and red mud

Chunguang Song et al.

Summary: The study shows that using red mud instead of clay to mix with ALTs can produce lightweight aggregates with excellent physical characteristics.

CHINESE JOURNAL OF CHEMICAL ENGINEERING (2021)

Article Materials Science, Ceramics

Assessment of mechanical and microstructural properties of geopolymers produced from metakaolin, silica fume, and red mud

Beatryz Mendes et al.

Summary: Geopolymers produced with sodium hydroxide solution, metakaolin, silica fume, and red mud were evaluated for their mechanical and microstructural properties. The study found that metakaolin mortars exhibited the best mechanical strengths when cured at 50 degrees C, while the use of red mud led to a decrease in strength. Additionally, an increase in thermal curing conditions and residue content resulted in the formation of more pores in the mortar matrix.

INTERNATIONAL JOURNAL OF APPLIED CERAMIC TECHNOLOGY (2021)

Article Green & Sustainable Science & Technology

Preparation, characterization and application of red mud, fly ash and desulfurized gypsum based eco-friendly road base materials

Yong Li et al.

Summary: This study investigated the preparation of road base materials using red mud, fly ash, and desulfurized gypsum, and their mechanical properties, durability, microstructure, and environmental performance. The results show that the composites have good compressive strength and durability at specific molar ratios, and are effective in preventing leaching of heavy metal ions.

JOURNAL OF CLEANER PRODUCTION (2021)

Article Chemistry, Physical

Porous geopolymer based eco-friendly multifunctional slow-release fertilizers for promoting plant growth

Haiyan Yan et al.

Summary: This study successfully prepared a novel multifunctional slow-release fertilizer containing N, P, and K nutrients using eco-friendly inorganic/organic composites as carriers, which demonstrated good water retention capacity, water absorbency in salt solutions, soil pH regulation, partial degradation in soil, and promotion of maize plant growth in the soil environment. The slow-release longevity of N nutrient in the fertilizer was more than 90 days, with a cumulative release rate of 51.4%, indicating the potential of three-dimensional network eco-friendly geopolymer with high porosity in nutrient loading and persistent slow-release performance.

COLLOIDS AND SURFACES A-PHYSICOCHEMICAL AND ENGINEERING ASPECTS (2021)

Article Construction & Building Technology

Effects of nano cotton stalk and palm leaf ashes on ultrahigh-performance concrete properties incorporating recycled concrete aggregates

Mohamed Amin et al.

Summary: The study investigated the effects of using NCSA and PLA as partial replacements for cement in UHPC, finding that substitutions with NCSA and PLA achieved the highest compressive strengths at 90 days and that a mixture of 20% PLA and 5% NCSA showed the highest values of splitting tensile strength, flexural strength, and elastic modulus.

CONSTRUCTION AND BUILDING MATERIALS (2021)

Article Construction & Building Technology

Magnesium industry waste and red mud to eco-friendly ternary binder: Producing more sustainable cementitious materials

Maysa Lorena Figueiredo Martins et al.

Summary: This study evaluated the feasibility of using magnesium industry waste and red mud as supplementary cementitious materials, developed a ternary binder with partial Portland cement substitution, and found that partial substitution of PC can produce eco-friendly binders that meet standards.

CONSTRUCTION AND BUILDING MATERIALS (2021)

Review Construction & Building Technology

A review on the utilization of red mud for the production of geopolymer and alkali activated concrete

Aman Kumar et al.

Summary: The production of ordinary Portland cement has harmful effects on the environment, leading to the utilization of industrial waste products to synthesize geopolymer materials and alkali-activated binders as an alternative. Red Mud, a harmful radioactive waste material, can be used in the synthesis of these materials, providing better environmental stability.

CONSTRUCTION AND BUILDING MATERIALS (2021)

Article Chemistry, Applied

Evaluation of red mud as oxygen carrier for chemical looping combustion of methane and biomass in fluidized bed

Qi Hong et al.

Summary: Red mud shows low reactivity with methane and better reactivity with biomass char. It exhibits stable reactivity during oxygen carrier cycles, but tends to agglomerate during methane fluidized bed experiments.

FUEL PROCESSING TECHNOLOGY (2021)

Review Green & Sustainable Science & Technology

Engineering properties of sustainable green concrete incorporating eco-friendly aggregate of crumb rubber: A review

Shaker M. A. Qaidi et al.

Summary: The disposal of waste rubber tires has become a major ecological issue globally due to their prolonged degrading period and severe hazard to the environment. Recycling waste rubber as construction material can help preserve depleting natural aggregate sources and protect the environment. This paper reviews research on using crumb rubber as eco-friendly aggregates in concrete and its impact on fresh and mechanical properties, aiming to update the database for further experimental and numerical research on rubberized concrete.

JOURNAL OF CLEANER PRODUCTION (2021)

Review Engineering, Environmental

Characteristic, hazard and iron recovery technology of red mud-A critical review

Xiao Liu et al.

Summary: This paper systematically reviews the iron recovery methods for high-iron RM, dividing them into physical separation, pyrometallurgy (reduction smelting and reduction roasting), and hydrometallurgy (acid leaching). The basic principles and effects of these technologies are summarized, as well as the advantages and disadvantages. Feasibility and economic cost are identified as main factors restricting industrial application.

JOURNAL OF HAZARDOUS MATERIALS (2021)

Article Construction & Building Technology

Study on the mechanical properties and microstructure of chitosan reinforced metakaolin-based geopolymer

Yangxin Qin et al.

Summary: This study investigated the effects of chitosan on metakaolin-based geopolymer and found that the presence of chitosan significantly improved the strength and flexural toughness of the geopolymer. The addition of chitosan led to an increase in compressive and flexural strength, with optimal conditions observed at a chitosan content of 1.0 wt%. The toughening mechanism of chitosan on geopolymer was attributed to the formation of C-O-Si bonds and a three-dimensional interpenetrating network at both molecular and submicroscopic levels.

CONSTRUCTION AND BUILDING MATERIALS (2021)

Article Green & Sustainable Science & Technology

Mechanism of magnetizing the Bayer red mud and meanwhile improving the cementitious activity of its tailings by using biomass

Yaguang Wang et al.

Summary: This study systematically investigated the effects of biomass as a reductant and alteration agent on the transformation of hematite into magnetite in BRM and the cementitious activity of tailings. The results showed that biomass can reduce the activation energy of hematite, increase magnetite yield in BRM, and enhance the cementitious activity of tailings.

JOURNAL OF CLEANER PRODUCTION (2021)

Review Green & Sustainable Science & Technology

Comprehensive utilization status of red mud in China: A critical review

Shaohan Wang et al.

Summary: In recent years, the environmental issues caused by the accumulation of red mud have become increasingly serious. Research on the comprehensive utilization of red mud is mainly focused on the fields of construction and chemical industry, environmental protection and agriculture, as well as valuable elements extraction industry. The current industrial consumption of red mud in China has been measured, and suggestions for solving the red mud problem have been proposed.

JOURNAL OF CLEANER PRODUCTION (2021)

Article Engineering, Environmental

Protonation stabilized high As/F mobility red mud for Pb/As polluted soil remediation

Dazhong Yang et al.

Summary: The protonation approach effectively immobilizes the As/F anions in red mud, meeting WHO standards, and allows for recycling as a heavy metal passivator in polluted soils. This green chemical strategy is cost-effective, eco-friendly, and has high economic feasibility with ecological benefits.

JOURNAL OF HAZARDOUS MATERIALS (2021)

Article Engineering, Chemical

An environmentally sustainable way for effective water purification by adsorptive red mud cementitious composite cubes modified with bentonite and activated carbon

Inci Sevgili et al.

Summary: By combining red mud with bentonite and activated carbon, effective water treatment methods for removing heavy metals have been researched, providing an important alternative for treating industrial wastewater. The designed adsorptive red mud cement paste cubes can improve water quality to drinking standards and can also be used in existing water treatment plants or pervious concrete roads to reduce pollution load.

SEPARATION AND PURIFICATION TECHNOLOGY (2021)

Article Green & Sustainable Science & Technology

Compressive Strength of Sustainable Geopolymer Concrete Composites: A State-of-the-Art Review

Hemn Unis Ahmed et al.

Summary: Geopolymer concrete, utilizing industrial or agricultural by-product ashes as binders, has emerged as a sustainable construction material due to environmental issues associated with cement production. Compressive strength of geopolymer concrete is influenced by various parameters such as curing temperature, sodium silicate content, and alkaline solution to binder ratio.

SUSTAINABILITY (2021)

Article Engineering, Environmental

Red mud for the efficient adsorption of U(VI) from aqueous solution: Influence of calcination on performance and mechanism

Wanying Wu et al.

Summary: This study produced macroporous iron and carbon combined calcined red mud (ICRM) and carbon calcined red mud (CRM) through calcination in the range of 500-800 degrees C, revealing advantageous performances with stable U adsorption capacities. The main adsorption mechanisms of ICRM are surface electrostatic attraction, physical adsorption by porous structure, and chemical adsorption by active Al and Fe components. Overall, ICRM offers theoretical guidances to radioactive drainage management and red mud reuse by exhibiting superior U adsorption capacity and positive potential charges under acidic conditions.

JOURNAL OF HAZARDOUS MATERIALS (2021)

Article Materials Science, Multidisciplinary

Research on High-Pressure Hydrochloric Acid Leaching of Scandium, Aluminum and Other Valuable Components from the Non-Magnetic Tailings Obtained from Red Mud after Iron Removal

Dmitry Zinoveev et al.

Summary: This study focused on the extraction of iron from red mud using high-pressure hydrochloric acid leaching method, investigated the factors influencing the dissolution behavior, proposed a mechanism for passing valuable elements into the solution, and developed novel flowsheets for red mud treatment.

METALS (2021)

Article Construction & Building Technology

Boosting the use of bauxite residue (red mud) in cement - Production of an Fe-rich calciumsulfoaluminate-ferrite clinker and characterisation of the hydration

Tobias Hertel et al.

Summary: Calciumsulfoaluminate-ferrite clinker was produced using bauxite residue, resulting in hydration products of ettringite, monosulfate, and hydrogarnet, leading to strength development due to rapid formation of ettringite mainly from ye'elimite.

CEMENT AND CONCRETE RESEARCH (2021)

Article Construction & Building Technology

The effect of using nano rice husk ash of different burning degrees on ultra-high-performance concrete properties

A. Serag Faried et al.

Summary: This study investigated the effect of seven different types of nano rice husk ash (NRHA) on the performance of ultra-high-performance concrete (UHPC). The results showed that the addition of NRHA can enhance the compressive strength and impermeability of UHPC.

CONSTRUCTION AND BUILDING MATERIALS (2021)

Article Construction & Building Technology

Production of lightweight aggregate ceramsite from red mud and municipal solid waste incineration bottom ash: Mechanism and optimization

Yuehui Sun et al.

Summary: RM and MSWIBA were converted into lightweight aggregate ceramsites through disc pelletization and high-temperature sintering. The study revealed the sintering mechanism and optimal production process based on evaluation of ceramsites performance under different production processes. Results showed that with an increase in RM proportion, the required sintering temperature increased while the properties of ceramsites decreased.

CONSTRUCTION AND BUILDING MATERIALS (2021)

Article Engineering, Environmental

Red mud-molten salt composites for medium-high temperature thermal energy storage and waste heat recovery applications

Argyrios Anagnostopoulos et al.

Summary: Red mud is an industrial waste of the aluminum industry, with only 15% currently utilized, but a new method utilizing RM to formulate CPCM has been proposed, showing good performance and suitability for waste heat recovery.

JOURNAL OF HAZARDOUS MATERIALS (2021)

Review Engineering, Chemical

Evaluation of red mud as a polymetallic source-A review

Shrey Agrawal et al.

Summary: Red mud as an industrial waste generated during alumina production poses environmental risks and high disposal costs, prompting the utilization of valuable minerals from it. Recovering metallic values from red mud can significantly improve process efficiency, reduce industrial liability, and minimize waste generation, offering potential strategic advantages for resource-deficient nations.

MINERALS ENGINEERING (2021)

Review Engineering, Environmental

Biotechnological trends and market impact on the recovery of rare earth elements from bauxite residue (red mud) - A review

Sandeep Panda et al.

Summary: The study highlights the potential of unexploited bauxite residues as a rich source of REEs, which could unlock approximately a 4.3 trillion-dollar economy globally. Despite environmental concerns and disposal challenges, bio-technological recovery of REEs from bauxite residues could be a promising alternative.

RESOURCES CONSERVATION AND RECYCLING (2021)

Article Engineering, Environmental

Red mud regulates arsenic fate at acidic pH via regulating arsenopyrite bio-oxidation and S, Fe, Al, Si speciation transformation

Duo-rui Zhang et al.

Summary: The study demonstrates that the addition of RM facilitates the bio-oxidation of arsenopyrite and the formation of stable nanoparticle precipitates, reducing the release of arsenic. However, excessive addition of RM leads to an increase in solution pH, inhibiting the dissolution of arsenopyrite and the release of arsenic.

WATER RESEARCH (2021)

Article Multidisciplinary Sciences

Effects of waste glass and waste marble on mechanical and durability performance of concrete

Jawad Ahmad et al.

Summary: Industrial waste has been increasing rapidly due to the growing population, leading to environmental pollution. Using industrial waste in concrete production can significantly reduce waste disposal. Waste glass and marble can be utilized as cement replacements or aggregates to enhance concrete strength. Research shows that workability of concrete decreases with higher content of waste glass and marble, while mechanical properties improve noticeably.

SCIENTIFIC REPORTS (2021)

Article Construction & Building Technology

Thermo- mechanical properties of alkali-activated slag-Red mud concrete

A. Bayat et al.

ROAD MATERIALS AND PAVEMENT DESIGN (2020)

Article Construction & Building Technology

Effect of nano-modified additives on properties of concrete mixtures during winter season

Alexander P. Svintsov et al.

CONSTRUCTION AND BUILDING MATERIALS (2020)

Article Green & Sustainable Science & Technology

Effect of different gypsums on the workability and mechanical properties of red mud-slag based grouting materials

Zhaofeng Li et al.

JOURNAL OF CLEANER PRODUCTION (2020)

Article Environmental Sciences

Effect of phosphogypsum and poultry manure on aggregate-associated alkaline characteristics in bauxite residue

Shengguo Xue et al.

JOURNAL OF ENVIRONMENTAL MANAGEMENT (2020)

Article Environmental Sciences

Feasibility study of red mud for geopolymer preparation: effect of particle size fraction

Jian Zhang et al.

JOURNAL OF MATERIAL CYCLES AND WASTE MANAGEMENT (2020)

Article Materials Science, Multidisciplinary

Experimental and modelling study of mixture design optimisation of glass fibre-reinforced concrete with combined utilisation of Taguchi and Extreme Vertices Design Techniques

Sadik Alper Yildizel et al.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2020)

Article Construction & Building Technology

The mechanical and microstructural properties of refuse mudstone-GGBS-red mud based geopolymer composites made with sand

Wei Zhou et al.

CONSTRUCTION AND BUILDING MATERIALS (2020)

Article Environmental Sciences

Environmental risks and mechanical evaluation of recycling red mud in bricks

F. Arroyo et al.

ENVIRONMENTAL RESEARCH (2020)

Article Chemistry, Multidisciplinary

Utilization of red mud for producing a high strength binder by composition optimization and nano strengthening

Sara Ahmed et al.

NANOTECHNOLOGY REVIEWS (2020)

Review Green & Sustainable Science & Technology

Geopolymers, inorganic polymers, alkali-activated materials and hybrid binders from bauxite residue (red mud) - Putting things in perspective

Tobias Hertel et al.

JOURNAL OF CLEANER PRODUCTION (2020)

Review Green & Sustainable Science & Technology

Fabrication and engineering properties of concretes based on geopolymers/alkali-activated binders - A review

Peng Zhang et al.

JOURNAL OF CLEANER PRODUCTION (2020)

Article Construction & Building Technology

Lightweight geopolymer-based mortars for the structural and energy retrofit of buildings

Fabio Longo et al.

ENERGY AND BUILDINGS (2020)

Article Engineering, Chemical

Clean utilization of high-iron red mud by suspension magnetization roasting

Xiao Liu et al.

MINERALS ENGINEERING (2020)

Article Engineering, Environmental

Extraction of Al and rare earths (Ce, Gd, Sc, Y) from red mud by aerobic and anaerobic bi-stage bioleaching

Duo-rui Zhang et al.

CHEMICAL ENGINEERING JOURNAL (2020)

Article Green & Sustainable Science & Technology

Potential use of industrial waste-red mud in developing hybrid composites: A waste management approach

S. Vigneshwaran et al.

JOURNAL OF CLEANER PRODUCTION (2020)

Article Construction & Building Technology

Role of Fe species in geopolymer synthesized from alkali-thermal pretreated Fe-rich Bayer red mud

Yong Hu et al.

CONSTRUCTION AND BUILDING MATERIALS (2019)

Review Engineering, Environmental

Utilization of red mud in road base and subgrade materials: A review

Emile Mukiza et al.

RESOURCES CONSERVATION AND RECYCLING (2019)

Review Engineering, Environmental

The composition, recycling and utilisation of Bayer red mud

M. A. Khairul et al.

RESOURCES CONSERVATION AND RECYCLING (2019)

Article Geochemistry & Geophysics

Identification of metal tolerant plant species for sustainable phytomanagement of abandoned red mud dumps

Meenu Gautam et al.

APPLIED GEOCHEMISTRY (2019)

Article Materials Science, Multidisciplinary

In situ XRD study on sintering mechanism of SiO2-Al2O3-CaO-MgO ceramics from red mud

Dejian Pei et al.

MATERIALS LETTERS (2019)

Article Construction & Building Technology

The microstructure and properties of ceramic tiles from solid wastes of Bayer red muds

Xiaohong Xu et al.

CONSTRUCTION AND BUILDING MATERIALS (2019)

Article Engineering, Chemical

Radiological assessment of the Bayer process

A. Goronovski et al.

MINERALS ENGINEERING (2019)

Review Geochemistry & Geophysics

A Review on Comprehensive Utilization of Red Mud and Prospect Analysis

Li Wang et al.

MINERALS (2019)

Article Green & Sustainable Science & Technology

Development and sustainability of industrial waste-based red mud hybrid composites

S. Vigneshwaran et al.

JOURNAL OF CLEANER PRODUCTION (2019)

Article Green & Sustainable Science & Technology

Utilization of red mud, slag and waste drilling fluid for the synthesis of slag-red mud cementitious material

Xiaowei Cheng et al.

JOURNAL OF CLEANER PRODUCTION (2019)

Article Engineering, Environmental

Synthesis of functionalised biochar using red mud, lignin, and carbon dioxide as raw materials

Kwangsuk Yoon et al.

CHEMICAL ENGINEERING JOURNAL (2019)

Article Green & Sustainable Science & Technology

Utilization of red mud in geopolymer-based pervious concrete with function of adsorption of heavy metal ions

Xiao Chen et al.

JOURNAL OF CLEANER PRODUCTION (2019)

Article Construction & Building Technology

Effects of red mud on the properties of fresh and hardened alkali-activated slag paste and mortar

A. Bayat et al.

CONSTRUCTION AND BUILDING MATERIALS (2018)

Article Construction & Building Technology

Effect of mechanical activation of red mud on the strength of geopolymer binder

Smita Singh et al.

CONSTRUCTION AND BUILDING MATERIALS (2018)

Article Construction & Building Technology

The NORM4Building database, a tool for radiological assessment when using by-products in building materials

Wouter Schroeyers et al.

CONSTRUCTION AND BUILDING MATERIALS (2018)

Article Construction & Building Technology

Environmental aspects and pavement properties of red mud waste as the replacement of mineral filler in asphalt mixture

Jizhe Zhang et al.

CONSTRUCTION AND BUILDING MATERIALS (2018)

Article Construction & Building Technology

A laboratory-scale experimental investigation on the reuse of a modified red mud in ceramic materials production

Cyril Scribot et al.

CONSTRUCTION AND BUILDING MATERIALS (2018)

Article Chemistry, Physical

Recycling of waste red mud for production of ceramic floor tile with high strength and lightweight

Wei Wang et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2018)

Article Construction & Building Technology

Effect of Red Mud Content on Strength and Efflorescence in Pavement using Alkali-Activated Slag Cement

Kim Hyeok-Jung et al.

INTERNATIONAL JOURNAL OF CONCRETE STRUCTURES AND MATERIALS (2018)

Article Engineering, Environmental

Identifying hotspots of environmental impact in the development of novel ik) inorganic polymer paving blocks from bauxite residue

P. James Joyce et al.

RESOURCES CONSERVATION AND RECYCLING (2018)

Article Metallurgy & Metallurgical Engineering

Enhanced selective leaching of scandium from red mud

Kanggen Zhou et al.

HYDROMETALLURGY (2018)

Article Chemistry, Multidisciplinary

Alumina Extraction from Red Mud by Magnetic Separation

Suprapto et al.

INDONESIAN JOURNAL OF CHEMISTRY (2018)

Proceedings Paper Materials Science, Multidisciplinary

Extraction of Iron values from Red mud

Shrey Agrawal et al.

MATERIALS TODAY-PROCEEDINGS (2018)

Article Engineering, Environmental

Dispersion and Sedimentation Characteristics of Red Mud

Shamshad Alam et al.

JOURNAL OF HAZARDOUS TOXIC AND RADIOACTIVE WASTE (2018)

Article Metallurgy & Metallurgical Engineering

The development of Bayer derived geopolymers as artificial aggregates

E. J. Jamieson et al.

HYDROMETALLURGY (2017)

Article Biotechnology & Applied Microbiology

Characterization of red mud as a structural fill and embankment material using bioremediation

Ipsita Panda et al.

INTERNATIONAL BIODETERIORATION & BIODEGRADATION (2017)

Article Green & Sustainable Science & Technology

Natural evolution of alkaline characteristics in bauxite residue

Xiangfeng Kong et al.

JOURNAL OF CLEANER PRODUCTION (2017)

Article Environmental Sciences

Radiological characterization and evaluation of high volume bauxite residue alkali activated concretes

Tom Croymans et al.

JOURNAL OF ENVIRONMENTAL RADIOACTIVITY (2017)

Article Construction & Building Technology

Study on the development of inorganic polymers from red mud and slag system: Application in mortar and lightweight materials

Patrick N. Lemougna et al.

CONSTRUCTION AND BUILDING MATERIALS (2017)

Article Construction & Building Technology

Development of alkali activated cements and concrete mixture design with high volumes of red mud

Pavel Krivenko et al.

CONSTRUCTION AND BUILDING MATERIALS (2017)

Article Construction & Building Technology

Synthesis of structural binder for red brick production based on red mud and fly ash activated using Ca(OH)2 and Na2CO3

Soon Yong Kim et al.

CONSTRUCTION AND BUILDING MATERIALS (2017)

Article Construction & Building Technology

Effects of red mud and Alkali-Activated Slag Cement on efflorescence in cement mortar

Suk-Pyo Kang et al.

CONSTRUCTION AND BUILDING MATERIALS (2017)

Article Chemistry, Physical

Potassium-rich biomass ashes as activators in metakaolin-based inorganic polymers

Arne Peys et al.

APPLIED CLAY SCIENCE (2016)

Article Green & Sustainable Science & Technology

Bauxite residue (red mud) as a pulverised fuel ash substitute in the manufacture of lightweight aggregate

Chloe J. Molineux et al.

JOURNAL OF CLEANER PRODUCTION (2016)

Review Green & Sustainable Science & Technology

Alkaline residues and the environment: a review of impacts, management practices and opportunities

Helena I. Gomes et al.

JOURNAL OF CLEANER PRODUCTION (2016)

Article Green & Sustainable Science & Technology

Advances in Understanding Environmental Risks of Red Mud After the Ajka Spill, Hungary

W. M. Mayes et al.

JOURNAL OF SUSTAINABLE METALLURGY (2016)

Article Construction & Building Technology

New perspectives and issues arising from the introduction of (NORM) residues in building materials: A critical assessment on the radiological behaviour

Cristina Nuccetelli et al.

CONSTRUCTION AND BUILDING MATERIALS (2015)

Article Green & Sustainable Science & Technology

Comparison of embodied energies of Ordinary Portland Cement with Bayer-derived geopolymer products

Evan Jamieson et al.

JOURNAL OF CLEANER PRODUCTION (2015)

Article Green & Sustainable Science & Technology

Characterization and microstructure observation of sintered red mud-fly ash mixtures at various elevated temperature

Sneha Samal et al.

JOURNAL OF CLEANER PRODUCTION (2015)

Article Construction & Building Technology

Modification of phase evolution in alkali-activated blast furnace slag by the incorporation of fly ash

Idawati Ismail et al.

CEMENT & CONCRETE COMPOSITES (2014)

Article Construction & Building Technology

Influence of red mud addition on rheological behavior and hardened properties of mortars

L. Senff et al.

CONSTRUCTION AND BUILDING MATERIALS (2014)

Article Green & Sustainable Science & Technology

Environmental assessment, management and utilization of red mud in China

Wanchao Liu et al.

JOURNAL OF CLEANER PRODUCTION (2014)

Article Materials Science, Ceramics

Synthesis and Characterization of Geopolymer from Bayer Red Mud with Thermal Pretreatment

Nan Ye et al.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2014)

Review Engineering, Environmental

Hidden values in bauxite residue (red mud): Recovery of metals

Yanju Liu et al.

WASTE MANAGEMENT (2014)

Article Construction & Building Technology

Development of paving blocks from synergistic use of red mud and fly ash using geopolymerization

Anuj Kumar et al.

CONSTRUCTION AND BUILDING MATERIALS (2013)

Article Engineering, Chemical

Proposal for resources, utilization and processes of red mud in India - A review

Sneha Samal et al.

INTERNATIONAL JOURNAL OF MINERAL PROCESSING (2013)

Article Construction & Building Technology

Manufacturing new ceramic materials from clay and red mud derived from the aluminium industry

L. Perez-Villarejo et al.

CONSTRUCTION AND BUILDING MATERIALS (2012)

Article Construction & Building Technology

The strength and microstructure of two geopolymers derived from metakaolin and red mud-fly ash admixture: A comparative study

Jian He et al.

CONSTRUCTION AND BUILDING MATERIALS (2012)

Article Engineering, Geological

Measuring pillar width in trona mines using a body wave based in-seam seismic technique

M. Ge et al.

INTERNATIONAL JOURNAL OF ROCK MECHANICS AND MINING SCIENCES (2012)

Article Environmental Sciences

Using imaging spectroscopy to map red mud dust waste: The Podgorica Aluminum Complex case study

Simone Pascucci et al.

REMOTE SENSING OF ENVIRONMENT (2012)

Article Environmental Sciences

Environmental impact of toxic elements in red mud studied by fractionation and speciation procedures

Radmila Milacic et al.

SCIENCE OF THE TOTAL ENVIRONMENT (2012)

Article Engineering, Environmental

Radiological restrictions of using red mud as building material additive

Hannian Gu et al.

WASTE MANAGEMENT & RESEARCH (2012)

Article Engineering, Environmental

Dispersal and Attenuation of Trace Contaminants Downstream of the Ajka Bauxite Residue (Red Mud) Depository Failure, Hungary

William M. Mayes et al.

ENVIRONMENTAL SCIENCE & TECHNOLOGY (2011)

Article Metallurgy & Metallurgical Engineering

Bauxite residue issues: II. options for residue utilization

C. Klauber et al.

HYDROMETALLURGY (2011)

Article Metallurgy & Metallurgical Engineering

Bauxite residue issues: I. Current management, disposal and storage practices

G. Power et al.

HYDROMETALLURGY (2011)

Article Chemistry, Physical

Spectroscopic studies of alkaline activated slag geopolymers

W. Mozgawa et al.

JOURNAL OF MOLECULAR STRUCTURE (2009)

Article Materials Science, Ceramics

Preparation of double-layer glass-ceramic/ceramic tile from bauxite tailings and red mud

Huizhi Yang et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2009)

Article Engineering, Environmental

Radiological aspects of the usability of red mud as building material additive

Janos Somlai et al.

JOURNAL OF HAZARDOUS MATERIALS (2008)

Article Materials Science, Multidisciplinary

Characterization of trace elements and radionuclides and their risk assessment in red mud

Akin Akinci et al.

MATERIALS CHARACTERIZATION (2008)

Review Materials Science, Multidisciplinary

Geopolymer technology:: the current state of the art

P. Duxson et al.

JOURNAL OF MATERIALS SCIENCE (2007)

Review Engineering, Environmental

Innovative methodologies for the utilisation of wastes from metallurgical and allied industries

Sanjay Kumar et al.

RESOURCES CONSERVATION AND RECYCLING (2006)

Article Nanoscience & Nanotechnology

The potential application of red mud in the production of castings

N Jústiz-Smith et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2006)

Article Chemistry, Applied

Evaluation of red mud as surface treatment for carbon steel prior painting

A Collazo et al.

PROGRESS IN ORGANIC COATINGS (2005)

Article Engineering, Environmental

Removal of dyes from aqueous solution using fly ash and red mud

SB Wang et al.

WATER RESEARCH (2005)

Article Materials Science, Ceramics

Phase constitution during sintering of red mud and red mud-fly ash mixtures

S Srikanth et al.

JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2005)

Article Engineering, Chemical

Efficiency of limestone and red mud barriers: laboratory column studies

K Komnitsas et al.

MINERALS ENGINEERING (2004)

Article Engineering, Environmental

Solid waste management in non-ferrous industries in India

A Agrawal et al.

RESOURCES CONSERVATION AND RECYCLING (2004)

Article Engineering, Environmental

Red mud addition in the raw meal for the production of Portland cement clinker

PE Tsakiridis et al.

JOURNAL OF HAZARDOUS MATERIALS (2004)

Article Construction & Building Technology

Properties and microstructure of the hardened alkali-activated red mud-slag cementitious material

ZH Pan et al.

CEMENT AND CONCRETE RESEARCH (2003)

Article Engineering, Environmental

Arsenic adsorption from aqueous solutions by activated red mud

HS Altundogan et al.

WASTE MANAGEMENT (2002)

Article Materials Science, Ceramics

Bauxite 'red mud' in the ceramic industry. Part 1: Thermal behaviour

VM Sglavo et al.

JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2000)