Related references
Note: Only part of the references are listed.
Article
Engineering, Civil
Jinyou Zhao et al.
Summary: This study investigates the overall buckling behaviors of welded I-section two-span continuous beams made of Q460 high strength steel, and assesses the reliability of the overall buckling design method specified in the Chinese standard for high strength steel structures (JGJ/T483-2020). Experimental tests and finite element analysis were conducted, and the results indicate that the design method in JGJ/T483-2020 is suitable for beams with non-dimensional slenderness value less than 1.5, but relatively conservative for beams with non-dimensional slenderness value greater than 1.5.
ENGINEERING STRUCTURES
(2022)
Article
Construction & Building Technology
Lei Gao et al.
Summary: The overall stability of BS700 high-strength steel axially compressed columns with box section was studied in this research. The failure mode was found to be bending buckling. It is recommended to use the curves of 3b type stipulated in GB50017-2017 and Eurocode.
JOURNAL OF CONSTRUCTIONAL STEEL RESEARCH
(2022)
Article
Construction & Building Technology
Mengjie Wang et al.
Summary: A comparative experimental investigation was conducted on Q460D and Q690D steels at temperatures ranging from 20 degrees C to 900 degrees C, showing negligible differences in the reduction factors for yield strengths. Excluding the effects of test conditions significantly reduced the differences between the 460 MPa and 690 MPa steels. Predictive equations were proposed for calculating the reduction factors of the mechanical properties of the steels at elevated temperatures.
JOURNAL OF CONSTRUCTIONAL STEEL RESEARCH
(2022)
Article
Chemistry, Physical
Jun Wang et al.
Summary: This study investigates the axial compressive mechanical performance of short high-strength steel-reinforced concrete columns. The results show that using high-strength steel can increase the bearing capacity of columns, but also increase the ductility coefficient. Increasing the steel ratio significantly improves the bearing capacity and ductility of the columns. Additionally, a change in the steel cross-section has a greater influence on the ductility of columns. The study also finds that existing standards cannot accurately predict the bearing capacity of the columns.
Article
Construction & Building Technology
Ahmed Elbably et al.
Summary: This paper investigates the mechanical behavior of encased steel-concrete (ESC) columns made of normal strength and high strength concrete. Experimental results show that ESC columns made of high strength concrete tend to fail abruptly with cracks passing through aggregates, while ESC columns made of normal strength concrete fail more gradually. Increasing the axial load ratio increases the lateral load capacity of the columns but results in a loss of ductility and stiffness beyond the peak point.
JOURNAL OF CONSTRUCTIONAL STEEL RESEARCH
(2022)
Article
Engineering, Civil
Jie Wang et al.
Summary: This study experimentally investigated the overall buckling of 12 welded H-section axial compression specimens made of high-strength steel, and conducted a parametric analysis via finite element simulation. The research found that as the strength of the steel increased, the axial ductility of the component decreased, and the size of the section where the strain entered the plasticity during buckling failure decreased. The finite element simulation verified the accuracy of the models and provided applicable buckling curves for the HSS-welded H-section axial compression members.
ENGINEERING STRUCTURES
(2021)
Article
Chemistry, Physical
Jun Wang et al.
Summary: The study found that using high-strength steel and increasing the steel ratio significantly enhances the bearing capacity of SRC columns. However, a dramatic increase in slenderness ratio leads to a sharp decrease in bearing capacity. Improving the confinement effect of stirrups on concrete can increase the utilization ratio of high-strength steel in SRC columns.
Article
Engineering, Civil
Mahmoud Aboukifa et al.
Summary: Ultra-High Performance Concrete (UHPC) is an advanced cementitious composite material with high ductility and durability, suitable for new construction applications, especially for next-generation bridge structures. Research shows that UHPC columns have reasonable ductility and drift capacity, and higher reinforcement ratio or grade is needed to fully utilize their superior mechanical properties.
ENGINEERING STRUCTURES
(2021)
Article
Engineering, Civil
Fei Yin et al.
Summary: Steel reinforced concrete columns are key vertical load-bearing members in super high-rise buildings. The steel sections and ratios significantly impact their seismic performance. The study found that columns with closed steel sections exhibit better seismic performance, and the steel ratio has a significant influence on the columns' behavior, providing important design insights.
Article
Construction & Building Technology
A. Gautham et al.
Summary: This study investigates the performance of SRC columns under combined axial and lateral cyclic loadings through experimental and numerical methods. The research evaluates parameters such as lateral strength, mode of failure, and energy dissipation potential, and examines the reliability of design guidelines in different damage regions. A parametric study using finite element software provides insights into the flexural capacity of SRC columns under varying axial load levels.
JOURNAL OF BUILDING ENGINEERING
(2021)
Article
Engineering, Civil
Qingxuan Shi et al.
Summary: This study investigated the seismic behavior of square concrete columns reinforced with Grade 600 MPa steel, and specified the service strength of Grade 600 MPa longitudinal bars by conducting tests on high-strength reinforced concrete cantilever columns. A new configuration of transverse reinforcement was proposed and applied in the specimens, achieving satisfactory seismic performance according to Chinese code GB 50011-2010. The study also provided design suggestions for ensuring seismic performance of these columns, extending the method for determining seismic bending moment capacity of RC column based on confined concrete theory.
Article
Engineering, Civil
Jin Jiang et al.
ENGINEERING STRUCTURES
(2020)
Article
Engineering, Civil
Chung-Che Chou et al.
ENGINEERING STRUCTURES
(2019)
Article
Construction & Building Technology
Jianyang Xue et al.
CONSTRUCTION AND BUILDING MATERIALS
(2019)
Article
Engineering, Civil
Weiqing Zhu et al.
ENGINEERING STRUCTURES
(2016)
Article
Materials Science, Multidisciplinary
Ji-Hwan Lee et al.
Article
Chemistry, Physical
Niranjan V. Ilawe et al.
JOURNAL OF CHEMICAL THEORY AND COMPUTATION
(2015)
Article
Construction & Building Technology
Hui Ma et al.
CONSTRUCTION AND BUILDING MATERIALS
(2013)
Article
Construction & Building Technology
Xuhong Zhou et al.
JOURNAL OF CONSTRUCTIONAL STEEL RESEARCH
(2010)
