Related references
Note: Only part of the references are listed.Intensive laser repair through additive manufacturing of high-strength martensitic stainless steel powders (I)-powder preparation, laser cladding and microstructures and properties of laser-cladded metals
Jie Ning et al.
JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2021)
Wire Arc Additive Manufacturing: A Comprehensive Review and Research Directions
Laukik P. Raut et al.
JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2021)
Hydrogen embrittlement of X2CrNiMoCuN25-6-3 super duplex stainless steel welded joints under cathodic protection
Aleksandra Swierczynska et al.
CONSTRUCTION AND BUILDING MATERIALS (2020)
Recent advances in hybrid organic-inorganic materials with spatial architecture for state-of-the-art applications
Wail Al Zoubi et al.
PROGRESS IN MATERIALS SCIENCE (2020)
Experimental observation of stress formation during selective laser melting using in situ X-ray diffraction
Felix Schmeiser et al.
ADDITIVE MANUFACTURING (2020)
Chemical stability of synergistic inorganic materials for enhancing electrochemical performance
Wail Al Zoubi et al.
COMPOSITES SCIENCE AND TECHNOLOGY (2020)
Behavior of the reversed austenite in CA-6NM martensitic stainless steel under cavitation
L. L. Santos et al.
WEAR (2020)
Plasticity of Bead-on-Plate Welds Made with the Use of Stored Flux-Cored Wires for Offshore Applications
Aleksandra Swierczynska et al.
MATERIALS (2020)
The heat affected zone of X20Cr13 martensitic stainless steel after multiple repair welding: Microstructure and mechanical properties assessment
Mohammad Shojaati et al.
INTERNATIONAL JOURNAL OF PRESSURE VESSELS AND PIPING (2020)
Identification of optimum working conditions in hydroelectric power plants for cavitation
Gokhan Kahraman et al.
ENGINEERING FAILURE ANALYSIS (2019)
Analysis of 410NiMo coating deposited by thermal spray in CA6NM martensitic stainless steel against erosion by cavitation
Emillyn Ferreira Trevisani Olivio et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2019)
The role of particle size and solids concentration on the transition from moderate to severe slurry wear regimes of ASTM A743 grade CA6NM stainless steel
D. A. Lopez et al.
TRIBOLOGY INTERNATIONAL (2018)
INFLUENCE OF CLADDING PARAMETERS WITH FCAW ON BEAD GEOMETRY WITH PLACKETT-BURMAN EXPERIMENT USED
R. Beczkowski
ARCHIVES OF METALLURGY AND MATERIALS (2018)
Using either Mean or RMS values to represent current in modeling of arc welding bead geometries
Diego Costa Correia Silva et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2017)
Phase structures and morphologies of tempered CA6NM stainless steel welded by hybrid laser-arc process
F. Mirakhorli et al.
MATERIALS CHARACTERIZATION (2017)
Macro-defects characterization in cast CA-6NM martensitic stainless steel
Shilan Meimandi et al.
MATERIALS CHARACTERIZATION (2017)
Effect of Peak Positioning Method on Accuracy of X-Ray Diffraction Residual Stress Measurement
M. Sedighi et al.
EXPERIMENTAL TECHNIQUES (2016)
Analysis of mean and RMS current welding in the pulsed TIG welding process
Tiago Vieira da Cunha et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2016)
Global and local characteristics of an autogenous single pass electron beam weld in thick gage UNS S41500 steel
S. Sarafan et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2016)
Quantitative Analysis of Martensite and Bainite Microstructures Using Electron Backscatter Diffraction
Yongzhe Wang et al.
MICROSCOPY RESEARCH AND TECHNIQUE (2016)
Distortion and residual stresses in electron beam-welded hydroelectric turbine materials
S. Sarafan et al.
SCIENCE AND TECHNOLOGY OF WELDING AND JOINING (2016)
Effect of compression Residual Stress on Fatigue Properties of Stainless Cast Steel
T. Hanaki et al.
21ST EUROPEAN CONFERENCE ON FRACTURE, (ECF21) (2016)
Characteristics of an autogenous single pass electron beam weld in thick gage CA6NM steel
S. Sarafan et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2015)
Microstructure and mechanical properties of hot wire laser clad layers for repairing precipitation hardening martensitic stainless steel
Peng Wen et al.
OPTICS AND LASER TECHNOLOGY (2015)
Microstructural effects on the fatigue crack growth resistance of a stainless steel CA6NM weld
Alexandre Trudel et al.
ENGINEERING FRACTURE MECHANICS (2014)
Fatigue crack growth in the heat affected zone of a hydraulic turbine runner weld
Alexandre Trudel et al.
INTERNATIONAL JOURNAL OF FATIGUE (2014)
A correlative approach to segmenting phases and ferrite morphologies in transformation-induced plasticity steel using electron back-scattering diffraction and energy dispersive X-ray spectroscopy
Azdiar A. Gazder et al.
ULTRAMICROSCOPY (2014)
Induction-assisted laser beam welding of a thermomechanically rolled HSLA S500MC steel: A microstructure and residual stress assessment
R. S. Coelho et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2013)
Microstructure and mechanical properties of laser-welded joints of TWIP and TRIP steels
L. Mujica et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2010)
Effect of process parameters and mathematical model for the prediction of bead geometry in pulsed GMA welding
P. Srinivasa Rao et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2009)
Residual stress and microstructure in welds of 13%Cr-4%Ni martensitic stainless steel
Denis Thibault et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2009)
Welding residual stresses in ferritic power plant steels
J. A. Francis et al.
MATERIALS SCIENCE AND TECHNOLOGY (2007)
Share Paper
