☆ 4.6 Article

Microstructure Evolution of Al6061 Alloy Made by Additive Friction Stir Deposition

MATERIALS (2022)

Related references

Note: Only part of the references are listed.

Article Engineering, Mechanical

Evaluation of Microstructure and Mechanical Properties of Al-Zn-Mg-Cu Alloy Repaired via Additive Friction Stir Deposition

D. Z. Avery et al.

Summary: Additive friction stir deposition (AFS-D), a novel solid-state additive manufacturing (AM) process, is used to repair damaged nonweldable aerospace materials. The microstructural evolution and mechanical performance of an additively repaired AA7075-T651 are quantified in this study. The heat-treated AFS-D repair shows good microstructure and mechanical properties, but has variability in elongation to failure and reduced fatigue life compared to the wrought material.

JOURNAL OF ENGINEERING MATERIALS AND TECHNOLOGY-TRANSACTIONS OF THE ASME (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructure evolution of 316L stainless steel during solid-state additive friction stir deposition

Hossein Beladi et al.

Summary: Solid-state additive friction stir deposition was used for three-dimensional printing of 316L stainless steel. The resulting microstructure was exceptionally fine, with a significantly different misorientation angle distribution from the original material, and a texture showing strong shear components.

PHILOSOPHICAL MAGAZINE (2022)

Add to Collection

Article Engineering, Mechanical

Fatigue assessment of additively-manufactured C-18150 copper alloy at room and elevated temperatures via a microstructure-sensitive algorithm

Arash P. Jirandehi et al.

Summary: The efficacy of a newly developed microstructure-sensitive fatigue framework for additively manufactured materials is evaluated at different environmental temperatures. C-18150 copper alloy samples fabricated by Laser Powder Bed Fusion (L-PBF) are subjected to fatigue testing at room temperature, 204 degrees C, and 426 degrees C. The damage representative, plastic strain energy, is studied using cyclic stress-strain hysteresis loop area measurements and analyzed with a microstructure-sensitive algorithm. A thermodynamics-based framework is employed to calculate Fracture Fatigue Entropy (FFE) for assessing the materials' fatigue performance. The results from the hysteresis loop and microstructure-sensitive method show consistent trends and magnitudes.

INTERNATIONAL JOURNAL OF FATIGUE (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Tensile Properties of Additively Manufactured C-18150 Copper Alloys

Congyuan Zeng et al.

Summary: The tensile properties of C-18150 copper alloy samples fabricated through laser powder-bed-fusion additive manufacturing (AM) are influenced by aging processes, with significant enhancement in tensile strength observed. However, the sacrifice of strain-to-failure values is noted after aging treatment. The optimal aging temperature for achieving the highest tensile strength is found to be 500 degrees C for 2 hours, while both tensile strength and ductility decrease at higher temperatures.

METALS AND MATERIALS INTERNATIONAL (2022)

Add to Collection

Proceedings Paper Materials Science, Multidisciplinary

A Critical Review on Heat Treatment of Aluminium Alloys

N. M. Siddesh Kumar et al.

Summary: Smart materials play a vital role in the modern world. Reinforcing different materials into aluminium can effectively improve its mechanical and material properties. Heat treatment, including solution heat treatment and aging, significantly affects the properties of aluminum alloys, such as strength and hardness.

MATERIALS TODAY-PROCEEDINGS (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Alloys-by-design: Application to new superalloys for additive manufacturing

Yuanbo T. Tang et al.

Summary: New grades of gamma/gamma' nickel-based superalloy for the additive manufacturing process were designed using computational approaches, with processing trials carried out using powder-based selective laser melting. The superior processability and mechanical behaviour of the new alloys were demonstrated through microstructural characterisation, calorimetry and hot tensile testing. Suggestions for refinements to the modelling approach were also made.

ACTA MATERIALIA (2021)

Add to Collection

Article Materials Science, Multidisciplinary

A meshfree computational framework for the numerical simulation of the solid -state additive manufacturing process, additive friction stir-deposition (AFS- D)

G. G. Stubblefield et al.

Summary: In this work, a fully coupled thermo-mechanical meshfree approach is developed for simulating the solid-state layer-by-layer additive manufacturing process AFS-D. The method uses a Lagrangian reference frame and solid mechanics formulation to resolve elastic and plastic strains. The simulation results are compared against experimental results for calibration, revealing temperature and strain rate gradients in the AFS-D process.

MATERIALS & DESIGN (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Elucidating the Effect of Additive Friction Stir Deposition on the Resulting Microstructure and Mechanical Properties of Magnesium Alloy WE43

M. B. Williams et al.

Summary: The effect of processing parameters on WE43 magnesium alloy processed via Additive Friction Stir Deposition (AFSD) was investigated. A parameterization study identified suitable parameters for bulk WE43 deposition, resulting in a refined homogenous microstructure and specific changes in mechanical properties compared to wrought material. Fatigue life in the low-cycle regime was decreased in as-deposited WE43, but comparable to wrought material in the high-cycle regime, demonstrating the potential of AFSD process for additively manufactured load-bearing components with WE43 magnesium alloy.

METALS (2021)

Add to Collection

Article Engineering, Manufacturing

Processing-structure-property correlation in additive friction stir deposited Ti-6Al-4V alloy from recycled metal chips

Priyanshi Agrawal et al.

Summary: Additive friction stir deposition (AFSD) is a novel thermo-mechanical solid state additive manufacturing process that enables the production of high-performance components from recycled metals, reducing energy consumption and environmental waste.

ADDITIVE MANUFACTURING (2021)

Add to Collection

Article Chemistry, Physical

Influence of Powder Bed Temperature on the Microstructure and Mechanical Properties of Ti-6Al-4V Alloy Fabricated via Laser Powder Bed Fusion

Lei-Lei Xing et al.

Summary: By pre-heating the powder bed, the thermal field during laser powder bed fusion can be enhanced, leading to improved microstructure and mechanical properties; Ti-6Al-4V alloy samples manufactured at different powder bed temperatures all show near-full densification with a ratio above 99.4%.

MATERIALS (2021)

Add to Collection

Review Chemistry, Physical

In-situ alloying in laser-based additive manufacturing processes: A critical review

Mohammad Hossein Mosallanejad et al.

Summary: The current challenge in additive manufacturing lies in the availability and cost of feedstock, with a growing number of studies focusing on in-situ alloying using elemental blends rather than pre-alloyed powders. This strategy provides greater flexibility to additive manufacturing methods, paving the way towards meeting the industry's evolving needs.

JOURNAL OF ALLOYS AND COMPOUNDS (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Directed energy deposition (DED) additive manufacturing: Physical characteristics, defects, challenges and applications

David Svetlizky et al.

Summary: Directed energy deposition (DED) is a branch of additive manufacturing (AM) processes that allows for site-specific deposition and repair, alloy design, and complex shape printing. This review critically examines recent advances in laser-material interactions, melt pool thermal behavior, and monitoring techniques, while also discussing critical processing variables, defect formation mechanisms, and high-end applications and challenges associated with DED processing.

MATERIALS TODAY (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Nanostructure Evolution in AA7075 Alloy Produced by Solid State Additive Manufacturing – Additive Friction Stir - Deposition

M Y Rekha et al.

MICROSCOPY AND MICROANALYSIS (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Solid-state additive manufacturing of aluminum and copper using additive friction stir deposition: Process-microstructure linkages

R. Joey Griffiths et al.

Summary: The study investigates the process-microstructure linkages in additive friction stir deposition using aluminum-magnesium-silicon alloy and copper, showing that the microstructure in aluminum-magnesium-silicon evolves primarily through continuous dynamic recrystallization, while copper exhibits heterogeneous microstructure due to discontinuous recrystallization. The differences in microstructure evolution are attributed to intrinsic thermomechanical properties and interactions with the tool head.

MATERIALIA (2021)

Add to Collection

Article Automation & Control Systems

Influence of heat treatment temperature on the microstructural, mechanical, and wear behavior of 316L stainless steel fabricated by laser powder bed additive manufacturing

Emre Tascioglu et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2020)

Add to Collection

Review Chemistry, Physical

On Residual Stress Development, Prevention, and Compensation in Metal Additive Manufacturing

Kevin Carpenter et al.

MATERIALS (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Influence of Grain Refinement and Microstructure on Fatigue Behavior for Solid-State Additively Manufactured Al-Zn-Mg-Cu Alloy

D. Z. Avery et al.

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Effect of Thermomechanical Processing on Fatigue Behavior in Solid-State Additive Manufacturing of Al-Mg-Si Alloy

Ben A. Rutherford et al.

METALS (2020)

Add to Collection

Review Materials Science, Multidisciplinary

Solid-State Metal Additive Manufacturing: A Review

Nihan Tuncer et al.

JOM (2020)

Add to Collection

Article Engineering, Manufacturing

Mapping of residual stresses in as-built Inconel 718 fabricated by laser powder bed fusion: A neutron diffraction study of build orientation influence on residual stresses

Prabhat Pant et al.

ADDITIVE MANUFACTURING (2020)

Add to Collection

Article Chemistry, Physical

Influence of Homogenization and Solution Treatments Time on the Microstructure and Hardness of Inconel 718 Fabricated by Laser Powder Bed Fusion Process

Eslam M. Fayed et al.

MATERIALS (2020)

Add to Collection

Article Engineering, Manufacturing

Morphological and microstructural investigation of the non-planar interface formed in solid-state metal additive manufacturing by additive friction stir deposition

Mackenzie E. J. Perry et al.

ADDITIVE MANUFACTURING (2020)

Add to Collection

Article Materials Science, Multidisciplinary

A Perspective on Solid-State Additive Manufacturing of Aluminum Matrix Composites Using MELD

R. Joey Griffiths et al.

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2019)

Add to Collection

Article Nanoscience & Nanotechnology

Effect of post-weld heat treatment on the mechanical behavior and dislocation density of friction stir welded Al6061

Amir Hossein Baghdadi et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2019)

Add to Collection

Article Chemistry, Multidisciplinary

Additive Friction Stir-Enabled Solid-State Additive Manufacturing for the Repair of 7075 Aluminum Alloy

R. Joey Griffiths et al.

APPLIED SCIENCES-BASEL (2019)

Add to Collection

Article Materials Science, Multidisciplinary

Gas-Atomized Al 6061 Powder: Phase Identification and Evolution During Thermal Treatment

Kyle Tsaknopoulos et al.

JOM (2019)

Add to Collection

Review Materials Science, Multidisciplinary

Review on design and structural optimisation in additive manufacturing: Towards next-generation lightweight structures

Janos Plocher et al.

MATERIALS & DESIGN (2019)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructure-deformation relationship of additive friction stir-deposition Al-Mg-Si

B. J. Phillips et al.

MATERIALIA (2019)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructure and mechanical properties of Al-Mg-Zr alloys processed by selective laser melting

Joseph R. Croteau et al.

ACTA MATERIALIA (2018)

Add to Collection

Article Materials Science, Multidisciplinary

Twinning-induced plasticity (TWIP) steels

Bruno C. De Cooman et al.

ACTA MATERIALIA (2018)

Add to Collection

Article Chemistry, Physical

Microstructure and fracture behavior of TiC particles reinforced Inconel 625 composites prepared by laser additive manufacturing

Ming-Yue Shen et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2018)

Add to Collection

Article Nanoscience & Nanotechnology

Influence of texture and grain refinement on the mechanical behavior of AA2219 fabricated by high shear solid state material deposition

O. G. Rivera et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2018)

Add to Collection

Article Nanoscience & Nanotechnology

Non-beam-based metal additive manufacturing enabled by additive friction stir deposition

Hang Z. Yu et al.

SCRIPTA MATERIALIA (2018)

Add to Collection

Review Engineering, Manufacturing

Potentials and strategies of solid-state additive friction-stir manufacturing technology: A critical review

F. Khodabakhshi et al.

JOURNAL OF MANUFACTURING PROCESSES (2018)

Add to Collection

Article Nanoscience & Nanotechnology

Microstructures and mechanical behavior of Inconel 625 fabricated by solid-state additive manufacturing

O. G. Rivera et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2017)

Add to Collection

Article Materials Science, Multidisciplinary

A framework to link localized cooling and properties of directed energy deposition (DED)-processed Ti-6A1-4V

Sarah J. Wolff et al.

ACTA MATERIALIA (2017)

Add to Collection

Article Nanoscience & Nanotechnology

Effect of ageing on tensile behavior of ultrafine grained Al 6061 alloy

P. Nageswara Rao et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2015)

Add to Collection

Article Materials Science, Multidisciplinary

Aging Behavior of Al 6061 Alloy Processed by High-Pressure Torsion and Subsequent Aging

Intan Fadhlina Mohamed et al.

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2015)

Add to Collection

Article Chemistry, Physical

Three-dimensional characterization of interaction between β precipitate and dislocation in Al-Mg-Si alloy

Kazuki Misumi et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2014)

Add to Collection

Article Nanoscience & Nanotechnology

Effect of cryorolling and warm rolling on precipitation evolution in Al 6061 alloy

P. Nageswara Rao et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2014)

Add to Collection

Article Instruments & Instrumentation

Characterization of Metal Powders Used for Additive Manufacturing

J. A. Slotwinski et al.

JOURNAL OF RESEARCH OF THE NATIONAL INSTITUTE OF STANDARDS AND TECHNOLOGY (2014)

Add to Collection

Article Engineering, Mechanical

Micromechanics Study of Fatigue Damage Incubation Following an Initial Overstrain

Yibin Xue et al.

JOURNAL OF ENGINEERING MATERIALS AND TECHNOLOGY-TRANSACTIONS OF THE ASME (2010)

Add to Collection

Article Materials Science, Multidisciplinary

Effect of heat treatment on microstructure and corrosion behavior of Al6061 alloy weldment

Z. Nikseresht et al.

MATERIALS & DESIGN (2010)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructure and Low-Cycle Fatigue of a Friction-Stir-Welded 6061 Aluminum Alloy

A. H. Feng et al.

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2010)

Add to Collection

Article Engineering, Mechanical

Modelling mechanical property recovery of a linepipe steel in annealing process

H. Li et al.

INTERNATIONAL JOURNAL OF PLASTICITY (2009)

Add to Collection

© Peeref 2019-2024. All rights reserved.