Related references
Note: Only part of the references are listed.Evolution of microstructure and residual stresses in gradually ground/polished 3Y-TZP
J. Minguela et al.
JOURNAL OF THE EUROPEAN CERAMIC SOCIETY (2020)
Interactions of grinding tool and supplied fluid
C. Heinzel et al.
CIRP ANNALS-MANUFACTURING TECHNOLOGY (2020)
Flexural strength and crystalline stability of a monolithic translucent zirconia subjected to grinding, polishing and thermal challenges
Raisa Hintz De Souza et al.
CERAMICS INTERNATIONAL (2020)
Influence of grinding parameters on phase transformation, surface roughness, and grinding cost of bioceramic partially stabilized zirconia (PSZ) using diamond grinding wheel
Javad Khodaii et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2019)
Study on grinding of pre-sintered zirconia using diamond wheel
P. Suya Prem Anand et al.
MATERIALS AND MANUFACTURING PROCESSES (2018)
Effect of grinding on subsurface modifications of pre-sintered zirconia under different cooling and lubrication conditions
P. Suya Prem Anand et al.
JOURNAL OF THE MECHANICAL BEHAVIOR OF BIOMEDICAL MATERIALS (2018)
Residual compressive surface stress increases the bending strength of dental zirconia
Masanao Inokoshi et al.
DENTAL MATERIALS (2017)
Grinding damage assessment on four high-strength ceramics
Jean-Jacques Canneto et al.
DENTAL MATERIALS (2016)
Study on cutting force model in ultrasonic vibration assisted side grinding of zirconia ceramics
Xingzhi Xiao et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2016)
The effect of grinding on the mechanical behavior of Y-TZP ceramics: A systematic review and meta-analyses
G. K. R. Pereira et al.
JOURNAL OF THE MECHANICAL BEHAVIOR OF BIOMEDICAL MATERIALS (2016)
Effect of grinding and heat treatment on the mechanical behavior of zirconia ceramic
Gabriela Freitas Ramos et al.
BRAZILIAN ORAL RESEARCH (2016)
Effect of grinding with diamond-disc and -bur on the mechanical behavior of a Y-TZP ceramic
G. K. R. Pereira et al.
JOURNAL OF THE MECHANICAL BEHAVIOR OF BIOMEDICAL MATERIALS (2014)
How and when does fabrication damage adversely affect the clinical performance of ceramic restorations?
Isabelle Denry
DENTAL MATERIALS (2013)
Phase transformation in high-speed cylindrical grinding of SiC and its effects on residual stresses
Jiaming Ni et al.
MATERIALS LETTERS (2012)
Microstructural changes in ground 3Y-TZP and their effect on mechanical properties
J. A. Munoz-Tabares et al.
ACTA MATERIALIA (2011)
Strength and grinding residual stresses of Y-TZP with duplex microstructures
Alberto Juy et al.
ENGINEERING FAILURE ANALYSIS (2009)
State of the art of zirconia for dental applications
Isabelle Denry et al.
DENTAL MATERIALS (2008)
Surface phase transformation during grinding of Y-TZP
Alberto Juy et al.
JOURNAL OF THE AMERICAN CERAMIC SOCIETY (2007)
The strength and hydrothermal stability of Y-TZP ceramics for dental applications
Tomaz Kosmac et al.
INTERNATIONAL JOURNAL OF APPLIED CERAMIC TECHNOLOGY (2007)
Influence of surface finish and residual stresses on the ageing sensitivity of biomedical grade zirconia
S Deville et al.
BIOMATERIALS (2006)
The influence of surface modification techniques on the performance of a Y-TZP dental ceramic
AR Curtis et al.
JOURNAL OF DENTISTRY (2006)
Origin of the hump on the left shoulder of the X-ray diffraction peaks observed in Y2O3-fully and partially stabilized ZrO2
J Kondoh
JOURNAL OF ALLOYS AND COMPOUNDS (2004)
Experimental investigations of machining characteristics and removal mechanisms of advanced ceramics in high speed deep grinding
H Huang et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2003)
Machining characteristics and surface integrity of yttria stabilized tetragonal zirconia in high speed deep grinding
H Huang
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2003)
Grinding induced damage in ceramics
B Zhang et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2003)
An investigation on the transformations in grinding affected layer of ZTC
XB Wang et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2000)
Share Paper
