☆ 4.5 Article

Effects of Heat Treatment on the Mechanical Behavior of Udimet 720 Nickel-Based Superalloy

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2022)

Related references

Note: Only part of the references are listed.

Article Materials Science, Multidisciplinary

Effect of Hot Deformation Parameters on the Dissolution of γ′ Precipitates for As-Cast Ni-Based Superalloys

Zhi-Peng Wan et al.

Summary: The dissolution and redistribution of gamma' precipitates in homogenized as-cast superalloy GH4720Li were systematically studied during heat treatment and hot deformation processes. The volume fraction of gamma' precipitates decreased with increasing temperature, reaching a dissolution equilibrium after 20 minutes of holding time. The dynamic dissolution of gamma' precipitates was accelerated with higher strain and lower strain rate during hot deformation, leading to a significant change in their morphology.

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Effect of Nb Content on Microstructure and Mechanical Properties of K4169-Type Superalloy

Liu-kun Zhang et al.

Summary: The influence of Nb content on the microstructure and mechanical property of K4169-type superalloy was investigated in this study. It was found that increasing Nb content can improve the strength and high-temperature resistance of the alloy, but may reduce elongation. Additionally, with the increase of aging temperature, the strength of the alloy will increase.

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Inhomogeneous Planar Distribution of γ′ Precipitates in Waspaloy Caused by Local Spatial Consumption of MC Carbides

Hongliang Liu et al.

Summary: The distribution of primary gamma' precipitates in Waspaloy after solution heat treatment was investigated at various temperatures. The inhomogeneity of gamma' precipitates increases as sub-solvus temperature increases, leading to the appearance of gamma'-precipitate-free zones after heat treatment at 1040 degrees C. Additionally, the inhomogeneous distribution of gamma' precipitates induces hardness fluctuation within the matrix.

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Acoustic Emission during Press-Brake Bending of SS 304L Sheets and its Correlation with Residual Stress Distribution after Bending

S. Lavanya et al.

Summary: Press-brake bending is an important sheet metal forming process used in automotive applications to fabricate different angles and channels. The plastic deformation during bending generates acoustic emission (AE) for online monitoring, aiding in defect identification and residual stress measurement. Analysis of AE signals shows that AE parameters increase with bend angle and correlate well with residual stress developed from plastic deformation.

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2022)

Add to Collection

Proceedings Paper Materials Science, Multidisciplinary

Effect of filler materials on dissimilar TIG welding of Inconel 718 to high strength steel

M. Anuradha et al.

Summary: The increasing demand for joining dissimilar materials in various manufacturing industries poses challenges in achieving quality joints. Tungsten Inert Gas welding is a candidate process for welding dissimilar materials, with welding parameters and filler materials playing a crucial role in the process. Results showed significant influence of welding current on properties of dissimilar welded joints, and higher tensile strength was achieved using Inconel-based filler materials.

MATERIALS TODAY-PROCEEDINGS (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Laser welding of dissimilar alloys between high tensile steel and Inconel alloy for high temperature applications

Muralimohan Cheepu et al.

Summary: In this study, laser welding was used to join Inconel 718 alloy with high tensile steel. The effects of welding parameters on microstructural characteristics and mechanical properties were investigated. It was found that the strength of the joints was influenced by laser power, and the segregation of elements at the fusion zone also affected the strength of the joints.

ADVANCES IN MATERIALS AND PROCESSING TECHNOLOGIES (2022)

Add to Collection

Article Materials Science, Multidisciplinary

Influence of joint interface on mechanical properties in dissimilar friction welds

Muralimohan Cheepu et al.

Summary: Friction welding is a solid-state joining process that provides sound welds without cracks. In this study, the dissimilar join of austenitic stainless steel to high tensile alloy steel was achieved using friction welding. The thickness of the intermixing zone in the welds was found to have an effect on the mechanical properties.

ADVANCES IN MATERIALS AND PROCESSING TECHNOLOGIES (2022)

Add to Collection

Article Chemistry, Multidisciplinary

Features of Acoustic Emission in Tensile Testing of Dissimilar Welded Joints of Pearlitic and Austenitic Steels

Vera Barat et al.

Summary: This study investigates the use of acoustic emission (AE) for diagnosing welding defects and diffusion interlayers in dissimilar welded joints of austenitic steel to pearlitic steel. The results show that AE method can effectively detect both typical welding defects and diffusion interlayers in welded joints of steels of different structural classes.

APPLIED SCIENCES-BASEL (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Synchrotron X-ray Photography Study of Cavitation Bubble Distribution in an Al-Cu Melt

Ruiquan Wang et al.

Summary: The distribution of cavitation bubbles in Al-18wt.%Cu during ultrasonic melt processing is influenced by acoustic intensity and distance from the radiation face. The bubbles show a clear difference in distribution, which significantly impacts the solidification structure.

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructure and High-Temperature Tensile Behavior of Ni-Based Superalloy EP741NP for Aerospace Applications

Sadananda Behera et al.

Summary: This paper explores the microstructural evolution and high-temperature tensile behavior of a Ni-based superalloy EP741NP for aerospace applications, finding that the predicted phase fractions of secondary and tertiary gamma prime (gamma ') match well with experimental results. The study shows that the strengthening gamma ' precipitate provides microstructural stability up to a certain temperature, after which the decrease in strength is attributed to the dissolution of tertiary precipitates hindering grain boundary motion at high temperatures. Fractographic studies reveal a mixed fracture mode, combining both ductile and brittle fracture characteristics.

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Tribological Performance of Molybdenum Stellite Alloys under Dry-Sliding Wear

Rachel Collier et al.

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2020)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Microstructure and Mechanical Properties of Friction-Welded and Post-Heat-Treated Inconel 718

Yu-Sik Kong et al.

TRANSACTIONS OF THE INDIAN INSTITUTE OF METALS (2020)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Effect of Welding Parameters on TIG Welding of Inconel 718 to AISI 4140 Steel

M. Anuradha et al.

TRANSACTIONS OF THE INDIAN INSTITUTE OF METALS (2020)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Characterization of Interfacial Microstructure in Friction Welds Between Inconel 718 and SM45C Steel

Muralimohan Cheepu et al.

TRANSACTIONS OF THE INDIAN INSTITUTE OF METALS (2020)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Growth Rate of Intermetallics in Aluminum to Copper Dissimilar Welding

Muralimohan Cheepu et al.

TRANSACTIONS OF THE INDIAN INSTITUTE OF METALS (2020)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Microstructure and Mechanical Properties for the Dissimilar Joining of Inconel 718 Alloy to High-Strength Steel by TIG Welding

M. Anuradha et al.

TRANSACTIONS OF THE INDIAN INSTITUTE OF METALS (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Spheroidization Mechanism of Lamellar δ Phase in Inconel 718 during Delta Processing

Hong-yan Gan et al.

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2020)

Add to Collection

Article Materials Science, Multidisciplinary

In Situ Process Monitoring for Additive Manufacturing Through Acoustic Techniques

Md Shahjahan Hossain et al.

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Prediction and Comparison of Creep Behavior of X20 Steam Plant Piping Network with Different Phenomenological Creep Models

Smith Salifu et al.

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2020)

Add to Collection

Article Physics, Applied

Predicting Creep Failure from Cracks in a Heterogeneous Material using Acoustic Emission and Speckle Imaging

Leevi Viitanen et al.

PHYSICAL REVIEW APPLIED (2019)

Add to Collection

Article Materials Science, Multidisciplinary

Corrosion Performance of 700 Series Stellite Alloys in Various Media

K. Kamal et al.

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2019)

Add to Collection

Article Engineering, Mechanical

Creep Life Prediction of Alloy 718 for Automotive Engine Materials

Yu Sik Kong et al.

INTERNATIONAL JOURNAL OF AUTOMOTIVE TECHNOLOGY (2018)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Modification of Larson-Miller Parameter Technique for Predicting Creep Life of Materials

Amitava Ghatak et al.

TRANSACTIONS OF THE INDIAN INSTITUTE OF METALS (2016)

Add to Collection

Article Materials Science, Multidisciplinary

Multimodal size distributions of γ′ precipitates during continuous cooling of UDIMET 720 Li

R. Radis et al.

ACTA MATERIALIA (2009)

Add to Collection

Article Nanoscience & Nanotechnology

The influence of heat treatment conditions on γ′ characteristics in Udimet® 720

H Monajati et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2004)

Add to Collection

Article Materials Science, Multidisciplinary

Cooling precipitation and strengthening study in powder metallurgy superalloy U720LI

J Mao et al.

METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2001)

Add to Collection

Article Materials Science, Multidisciplinary

An investigation on quench cracking behavior of superalloy Udimet 720LI using a fracture mechanics approach

J Mao et al.

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2000)

Add to Collection

© Peeref 2019-2024. All rights reserved.