☆ 4.5 Article

Microstructure and Mechanical Properties of a High-Ductility Al-Zn-Mg-Cu Aluminum Alloy Fabricated by Wire and Arc Additive Manufacturing

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2022)

Related references

Note: Only part of the references are listed.

Article Materials Science, Multidisciplinary

Fabrication of bulk Al-Co-Cr-Fe-Ni high-entropy alloy using combined cable wire arc additive manufacturing (CCW-AAM): Microstructure and mechanical properties

Qingkai Shen et al.

Summary: In this study, a new type of combined cable wire (CCW) was designed and developed for arc additive manufacturing of non-equiatomic high-entropy alloy, showing high deposition efficiency, energy saving capability, and superior mechanical properties. The microstructural observations revealed BCC and FCC phases, good bonding between layers, and defect-free microstructure in the developed alloy. By controlling heat input through torch travel speed, the microstructure and mechanical properties of the alloy can be managed effectively.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2021)

Add to Collection

Article Chemistry, Physical

Atomic-scale investigation of the heterogeneous precipitation in the E (Al18Mg3Cr2) dispersoid of 7075 aluminum alloy

Lipeng Ding et al.

Summary: The heterogeneous precipitation of the eta phase on the E dispersoids of the 7075 aluminum alloy was investigated, revealing that the B particles are heterogeneously precipitated at the E particle interface, stabilizing the E/Al interface and increasing the drive force of heterogeneous precipitation.

JOURNAL OF ALLOYS AND COMPOUNDS (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Investigation of Microstructure and Fracture Mechanism of Al-5.0Mg Alloys Fabricated by Wire Arc Additive Manufacturing

Yanfei Geng et al.

Summary: The study focused on the anisotropy of the microstructure and mechanical properties of Al-5.0Mg alloys in different orientations. It found that the microstructure in the horizontal direction is relatively homogeneous, and samples fabricated by WAAM-CMT exhibit better mechanical properties in that orientation compared to the as-cast alloy.

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Arc Additively Manufactured 5356 Aluminum Alloy with Cable-Type Welding Wire: Microstructure and Mechanical Properties

Jiankun Wang et al.

Summary: The study investigated the use of cable-type welding wire (CWW) in wire arc additive manufacturing (WAAM) to manufacture thin-walled AA5356 aluminum alloy, showing improved quality built parts. The grain morphology, phase in micro-constituents, and defect formation were analyzed through optical micrography and XRD. Mechanical tests revealed an increase in ultimate tensile strength and yield strength compared to casting aluminum alloy, highlighting the advantages of WAAM with CWW.

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Comparative study of deposition patterns for DED-Arc additive manufacturing of Al-4046

Markus Koehler et al.

Summary: Deposition pattern plays a significant role in metal additive manufacturing quality, with the study showing that the S pattern leads to more uniform temperature distribution, improved microstructure, and reduced residual stress formation.

MATERIALS & DESIGN (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Mechanical properties and precipitation behavior of the heat-treated wire plus arc additively manufactured 2219 aluminum alloy

Yinghui Zhou et al.

Summary: The dense 2219 Al alloy was successfully fabricated using Wire + Arc additive manufacturing technology, followed by solution and aging (T6) heat treatment to improve performance. The precipitation strengthening of the theta '' phase improves with increasing solution temperature, enhancing the mechanical properties of the material.

MATERIALS CHARACTERIZATION (2021)

Add to Collection

Article Automation & Control Systems

Effect of pulsed metal inert gas (pulsed-MIG) and cold metal transfer (CMT) techniques on hydrogen dissolution in wire arc additive manufacturing (WAAM) of aluminium

Karan S. Derekar et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructure, defects, and mechanical properties of wire plus arc additively manufactured Al-Cu4.3-Mg1.5 alloy

Jianglong Gu et al.

MATERIALS & DESIGN (2020)

Add to Collection

Article Chemistry, Physical

Welding and additive manufacturing with nanoparticle-enhanced aluminum 7075 wire

Daniel Oropeza et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2020)

Add to Collection

Article Engineering, Manufacturing

Effect of heat treatment on microstructure, hardness and corrosion resistance of 7075 Al alloys fabricated by SLM

Peng Liu et al.

JOURNAL OF MANUFACTURING PROCESSES (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructure evolution of annealed 7075 aluminum alloy and its influence on room-temperature plasticity

Lin Hua et al.

MATERIALS & DESIGN (2020)

Add to Collection

Review Chemistry, Physical

Recent advances in ageing of 7xxx series aluminum alloys: A physical metallurgy perspective

Abolfazl Azarniya et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2019)

Add to Collection

Article Engineering, Manufacturing

Microstructure and mechanical properties of wire plus arc additively manufactured 2024 aluminum alloy components: As-deposited and post heat-treated

Zewu Qi et al.

JOURNAL OF MANUFACTURING PROCESSES (2019)

Add to Collection

Article Chemistry, Physical

Influence of manufacturing geometric defects on the mechanical properties of AlSi10Mg alloy fabricated by selective laser melting

Panding Wang et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2019)

Add to Collection

Article Engineering, Mechanical

Dynamic changes of mechanical properties induced by friction in the Archard wear model

Yanfei Liu et al.

WEAR (2019)

Add to Collection

Article Engineering, Industrial

Workpiece vibration augmented wire arc additive manufacturing of high strength aluminum alloy

Chen Zhang et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2019)

Add to Collection

Review Materials Science, Multidisciplinary

A review of wire arc additive manufacturing and advances in wire arc additive manufacturing of aluminium

K. S. Derekar

MATERIALS SCIENCE AND TECHNOLOGY (2018)

Add to Collection

Article Engineering, Mechanical

Formation and improvement of surface waviness for additive manufacturing 5A06 aluminium alloy component with GTAW system

Haibin Geng et al.

RAPID PROTOTYPING JOURNAL (2018)

Add to Collection

Article Materials Science, Multidisciplinary

Gas tungsten arc welding of 7075 aluminum alloy: microstructure properties, impact strength, and weld defects

Bekir Cevik

MATERIALS RESEARCH EXPRESS (2018)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructure and Ratcheting Behavior of Additive Manufactured 4043 Aluminum Alloy

Yuan Wang et al.

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2018)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructure and mechanical properties of wire plus arc additively manufactured Al-Mg-Si aluminum alloy

Zewu Qi et al.

MATERIALS LETTERS (2018)

Add to Collection

Article Engineering, Mechanical

Formability of a wire arc deposited aluminium alloy

C. M. A. Silva et al.

JOURNAL OF THE BRAZILIAN SOCIETY OF MECHANICAL SCIENCES AND ENGINEERING (2017)

Add to Collection

Article Chemistry, Multidisciplinary

A Comparative Study of Additively Manufactured Thin Wall and Block Structure with Al-6.3%Cu Alloy Using Cold Metal Transfer Process

Baoqiang Cong et al.

APPLIED SCIENCES-BASEL (2017)

Add to Collection

Article Chemistry, Physical

Influence of repetitious non-isothermal aging on microstructure and strength of Al-Zn-Mg-Cu alloy

Yuan Liu et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2016)

Add to Collection

Article Nanoscience & Nanotechnology

The strengthening effect of inter-layer cold working and post-deposition heat treatment on the additively manufactured Al-6.3Cu alloy

Jianglong Gu et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2016)

Add to Collection

Article Nanoscience & Nanotechnology

Evolution of precipitate microstructure during stress aging of an Al-Zn-Mg-Cu alloy

Wei Guo et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2015)

Add to Collection

Article Materials Science, Multidisciplinary

Heating aging behavior of Al-8.35Zn-2.5Mg-2.25Cu alloy

Yan Liu et al.

MATERIALS & DESIGN (2014)

Add to Collection

Article Chemistry, Physical

Microstructure and tensile properties of large-size 7055 aluminum billets fabricated by spray forming rapid solidification technology

Yu Hongchun et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2013)

Add to Collection

Article Nanoscience & Nanotechnology

Ultrafine grains and the Hall-Petch relationship in an Al-Mg-Si alloy processed by high-pressure torsion

Aicha Loucif et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2012)

Add to Collection

Article Materials Science, Multidisciplinary

Development of ultrafine grained high strength age hardenable Al 7075 alloy by cryorolling

Sushanta Kumar Panigrahi et al.

MATERIALS & DESIGN (2011)

Add to Collection

Article Nanoscience & Nanotechnology

Structure-property correlations in Al 7050 and Al 7055 high-strength aluminum alloys

M. Dixit et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2008)

Add to Collection

© Peeref 2019-2024. All rights reserved.