Related references
Note: Only part of the references are listed.Dry Machining Performance Studies on TiAlSiN Coated Inserts in Turning of AISI 420 Martensitic Stainless Steel and Multi-Criteria Decision Making Using Taguchi-DEAR Approach
C. Moganapriya et al.
SILICON (2022)
Multi Criteria Decision Making of Vibration Assisted EDM Process Parameters on Machining Silicon Steel Using Taguchi-DEAR Methodology
Nguyen Huu Phan et al.
SILICON (2021)
Optimization and measurement of flank wear and surface roughness via Taguchi based grey relational analysis
Hilmi Peksen et al.
MATERIALS AND MANUFACTURING PROCESSES (2021)
Parameter optimization of copper nanoparticle synthesis by electrodeposition process using RSM and CS
A. Tamilvanan et al.
MATERIALS TODAY-PROCEEDINGS (2021)
Technical performance of nano-layered CNC cutting tool inserts-An extensive review
C. Moganapriya et al.
MATERIALS TODAY-PROCEEDINGS (2021)
Achieving machining effectiveness for AISI 1015 structural steel through coated inserts and grey-fuzzy coupled Taguchi optimization approach
C. Moganapriya et al.
STRUCTURAL AND MULTIDISCIPLINARY OPTIMIZATION (2021)
Cutting Performance and Wear Behavior of AlTiN- and TiAlSiN-Coated Carbide Tools During Dry Milling of Ti-6Al-4V
Jie Liu et al.
ACTA METALLURGICA SINICA-ENGLISH LETTERS (2020)
Electrochemical and Tribological Properties of CrAlN, TiAlN, and CrTiN Coatings in Water-Based Cutting Fluid
Zhiwei Wu et al.
JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2020)
Multi-objective optimization of turning parameters for targeting surface roughness and maximizing material removal rate in dry turning of AISI 316L with PVD-coated cermet insert
Youssef Touggui et al.
SN APPLIED SCIENCES (2020)
The Performance of TiAlSiN Coated Cemented Carbide Tools Enhanced by Inserting Ti Interlayers
Guodong Li et al.
METALS (2019)
Multi-response optimization of 67Ni18Cr5Si4B coating by HVOF spray using Taguchi-OEC technique
Van-Chien Dinh et al.
JOURNAL OF ADHESION SCIENCE AND TECHNOLOGY (2019)
ANFIS based prediction and parametric analysis during turning operation of stainless steel 202
Ishwer Shivakoti et al.
MATERIALS AND MANUFACTURING PROCESSES (2019)
Effect of cutting parameters on cutting force and surface roughness during machining microalloyed steel: Comparison between ferrite-pearlite, tempered martensite and ferrite-bainite-martensite microstructures
V. Sivaraman et al.
PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE (2018)
Effect of cutting parameters on wear behavior of coated tool and surface roughness in high-speed turning of 300M
Guangming Zheng et al.
MEASUREMENT (2018)
Multi Criteria Decision Making of Abrasive Flow Oriented Process Parameters in Abrasive Water Jet Machining Using Taguchi-DEAR Methodology
T. Muthuramalingam et al.
SILICON (2018)
Modeling and optimization for fly ash reinforced bronze-based composite materials using multi objective Taguchi technique and regression analysis
Husamettin Kus et al.
INDUSTRIAL LUBRICATION AND TRIBOLOGY (2018)
Limiting conditions for application of PVD (TiAlN) and CVD (TiCN/Al2O3/TiN) coated cemented carbide grades in the turning of hardened steels
Denis Boing et al.
WEAR (2018)
Influence of Coating Material and Cutting Parameters on Surface Roughness and Material Removal Rate in Turning Process Using Taguchi Method
C. Moganapriya et al.
MATERIALS TODAY-PROCEEDINGS (2018)
MODELING AND OPTIMIZATION OF FACE MILLING PROCESS PARAMETERS FOR AISI 4140 STEEL
Gokhan Basar et al.
TEHNICKI GLASNIK-TECHNICAL JOURNAL (2018)
OPTIMIZATION OF MACHINING PARAMETERS IN FACE MILLING USING MULTI-OBJECTIVE TAGUCHI TECHNIQUE
Yusuf Fedai et al.
TEHNICKI GLASNIK-TECHNICAL JOURNAL (2018)
Tribomechanical behavior of TiCN/TiAlN/WC-C multilayer film on cutting tool inserts for machining
Chinnasamy Moganapriya et al.
MATERIALS TESTING (2017)
Optimization of Machining Parameters in Turning of AISI 4340 Steel under Cryogenic Condition Using Taguchi Technique
Sanchit Kumar Khare et al.
MANUFACTURING SYSTEMS 4.0 (2017)
Multi-response milling process optimization using the Taguchi method coupled to grey relational analysis
Subramaniam Shankar et al.
MATERIALS TESTING (2016)
Study on microstructure and its formation mechanism, and mechanical properties of TiB2-TiC laminated Ti(C5N5) composite ceramic cutting tool material
Bin Zou et al.
INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS (2014)
Metallurgical Characteristics of TiAlN/AlCrN Coating Synthesized by the PVD Process on a Cutting Insert
T. Sampath Kumar et al.
JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2014)
Structural optimization of the cross-beam of a gantry machine tool based on grey relational analysis
Shihao Liu et al.
STRUCTURAL AND MULTIDISCIPLINARY OPTIMIZATION (2014)
Analysis on Drilling of Glass Fiber-Reinforced Polymer (GFRP) Composites Using Grey Relational Analysis
K. Palanikumar et al.
MATERIALS AND MANUFACTURING PROCESSES (2012)
Multi response optimisation of CNC turning parameters via Taguchi method-based response surface analysis
Ilhan Asilturk et al.
MEASUREMENT (2012)
Optimization of laser butt welding parameters based on the orthogonal array with fuzzy logic and desirability approach
P. Sathiya et al.
STRUCTURAL AND MULTIDISCIPLINARY OPTIMIZATION (2011)
Microstructure and properties of TiAlSiN coatings prepared by hybrid PVD technology
Donghai Yu et al.
THIN SOLID FILMS (2009)
Multi-objective optimization of multipass turning processes
N. R. Abburi et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2007)
Genetic algorithm-based multi-objective optimization of cutting parameters in turning processes
RQ Sardiñas et al.
ENGINEERING APPLICATIONS OF ARTIFICIAL INTELLIGENCE (2006)
Investigation of the cutting parameters depending on process sound during turning of AISI 304 austenitic stainless steel
Z Tekiner et al.
MATERIALS & DESIGN (2004)
Determination of optimum cutting parameters during machining of AISI 304 austenitic stainless steel
I Korkut et al.
MATERIALS & DESIGN (2004)
Mechanical properties and failure modes of TiAl(Si)N single and multilayer thin films
O Durand-Drouhin et al.
SURFACE & COATINGS TECHNOLOGY (2003)
A study of flank wear in orthogonal cutting with internal cooling
H Zhao et al.
WEAR (2002)
Share Paper
