☆ 4.7 Article

Achieving high strength and ductility in selective laser melting Ti-6Al-4V alloy by laser shock peening

JOURNAL OF ALLOYS AND COMPOUNDS (2022)

Related references

Note: Only part of the references are listed.

Article Chemistry, Physical

Effect of dynamic recrystallization on texture orientation and grain refinement of Ti6Al4V titanium alloy subjected to laser shock peening

Xinlei Pan et al.

Summary: This paper systematically investigated the DRX mechanism and its effects on grain refinement in Ti6Al4V titanium alloy subjected to LSP using EBSD and TEM characterization. The results showed that the DRX mechanism induced by shear bands played a vital role in texture transition and grain refinement during LSP.

JOURNAL OF ALLOYS AND COMPOUNDS (2021)

Add to Collection

Article Optics

Strengthening characteristics in TC17 titanium alloy treated during LSP

Yingwu Fang

Summary: The study investigated the strengthening characteristics of TC17 titanium alloy treated during laser shock processing (LSP) through simulation and experiment. It was found that the spot overlap ratio has a significant impact on the distribution of residual stresses, and adopting a 60% overlap ratio can greatly increase residual compressive stress.

OPTIK (2021)

Add to Collection

Review Engineering, Manufacturing

A review on wire and arc additive manufacturing of titanium alloy

Zidong Lin et al.

Summary: Wire and arc additive manufacturing (WAAM) is an economic and efficient technology suitable for producing large-scale metallic components, particularly in the fabrication of near-net-shape and large-scale titanium alloys. It has been significantly noticed and adopted due to its high deposition rate, low machinery cost, and shortened lead time compared to other powder-based additive manufacturing techniques.

JOURNAL OF MANUFACTURING PROCESSES (2021)

Add to Collection

Article Engineering, Industrial

Effects of laser shock peening on microstructural evolution and wear property of laser hybrid remanufactured Ni25/Fe104 coating on H13 tool steel

H. F. Lu et al.

Summary: Laser cladding and massive laser shock peening treatment were used to repair damaged H13 tool steel, improving the mechanical properties of the coating and enhancing its wear resistance. The treatment transformed residual stress, generated high-density dislocations and mechanical twins in the coating, and induced surface nanocrystallization to improve microhardness and wear resistance.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2021)

Add to Collection

Article Engineering, Manufacturing

Experimental realisation of build orientation effects on the mechanical properties of truly as-built Ti-6Al-4V SLM parts

Alireza Dareh Baghi et al.

Summary: The study found that vertically built parts are prone to premature fracture in their truly as-built condition, while horizontally fabricated parts perform similarly to post-treated samples. Additionally, the analysis of the tensile test results showed that the fracture stress of truly as-built vertical parts is below the yield stress of horizontal parts, at approximately 38% of the Ultimate Tensile Strength.

JOURNAL OF MANUFACTURING PROCESSES (2021)

Add to Collection

Review Chemistry, Physical

In-situ alloying in laser-based additive manufacturing processes: A critical review

Mohammad Hossein Mosallanejad et al.

Summary: The current challenge in additive manufacturing lies in the availability and cost of feedstock, with a growing number of studies focusing on in-situ alloying using elemental blends rather than pre-alloyed powders. This strategy provides greater flexibility to additive manufacturing methods, paving the way towards meeting the industry's evolving needs.

JOURNAL OF ALLOYS AND COMPOUNDS (2021)

Add to Collection

Article Engineering, Industrial

Uncovering the coupled impact of defect morphology and microstructure on the tensile behavior of Ti-6Al-4V fabricated via laser powder bed fusion

Timothy Montalbano et al.

Summary: This paper presents a systematic approach to relate mechanical properties and microstructure in the keyhole and lack of fusion domains for Ti-6Al-4V parts. It is shown that, at a similar amount of defects, it is more favorable to be in the keyhole domain than in the lack of fusion domain, due to higher sphericity and crystallographic texture. This finding is critical in ensuring optimal part performance in SLM Ti-6Al-4V parts.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2021)

Add to Collection

Article Multidisciplinary Sciences

Cryoforged nanotwinned titanium with ultrahigh strength and ductility

Shiteng Zhao et al.

Summary: Nanostructured metals are usually strong due to high internal boundary density, limiting dislocation mean free path, but also more brittle. Nanotwinned materials can overcome this trade-off. A new nanostructuring method enhances the strength and ductility of titanium.

SCIENCE (2021)

Add to Collection

Article Materials Science, Coatings & Films

Laser shock peening regulating aluminum alloy surface residual stresses for enhancing the mechanical properties: Roles of shock number and energy

Zhaoru He et al.

Summary: The use of laser shock peening (LSP) on aircraft 5A06 aluminum alloy resulted in significant enhancements in surface properties and mechanical performance, including micro-hardness and tensile strength. Additionally, improvements were observed in friction coefficient and surface wear, demonstrating the effectiveness of LSP in enhancing the material's mechanical properties.

SURFACE & COATINGS TECHNOLOGY (2021)

Add to Collection

Article Materials Science, Coatings & Films

Achieving excellent wear and corrosion properties in laser additive manufactured CrMnFeCoNi high-entropy alloy by laser shock peening

Zhaopeng Tong et al.

Summary: This study aims to fabricate a high-entropy alloy with excellent wear and corrosion properties through laser additive manufacturing and laser shock peening. The results showed that the friction coefficients and wear rates significantly decreased after laser shock peening, leading to improved wear and corrosion resistance.

SURFACE & COATINGS TECHNOLOGY (2021)

Add to Collection

Article Engineering, Manufacturing

Influence of substructures on the selective laser melted Ti-6Al-4V alloy as a function of laser re-melting

J. Karimi et al.

Summary: The study explores the effects of melting sequence on the microstructure, substructure, and mechanical properties of SLM Ti6Al4V alloys. Results show that increasing melting sequence leads to higher density of twins and dislocations, as well as improved tensile strength properties.

JOURNAL OF MANUFACTURING PROCESSES (2021)

Add to Collection

Article Chemistry, Physical

Microstructural evolution and mechanical properties of Inconel 718 superalloy thin wall fabricated by pulsed plasma arc additive manufacturing

Kaibo Wang et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2020)

Add to Collection

Article Nanoscience & Nanotechnology

Effects of laser shock peening on microstructure and fatigue behavior of Ti-6Al-4V alloy fabricated via electron beam melting

Xinyuan Jin et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)

Add to Collection

Article Engineering, Manufacturing

Effects of ultrasonic peening treatment in three directions on grain refinement and anisotropy of cold metal transfer additive manufactured Ti-6Al-4V thin wall structure

Jian Gou et al.

JOURNAL OF MANUFACTURING PROCESSES (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructural evolution and stress state related to mechanical properties of electron beam melted Ti-6Al-4V alloy modified by laser shock peening

Liang Lan et al.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2020)

Add to Collection

Article Chemistry, Physical

The compound process of laser shock peening and vibratory finishing and its effect on fatigue strength of Ti-3.5Mo-6.5Al-1.5Zr-0.25Si titanium alloy

Sihai Luo et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2019)

Add to Collection

Article Chemistry, Physical

The effect of heat treatment on microstructure evolution and tensile properties of selective laser melted Ti6Al4V alloy

Zulei Liang et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2019)

Add to Collection

Article Engineering, Mechanical

Plastic-deformation-driven SiC nanoparticle implantation in an Al surface by laser shock wave: Mechanical properties, microstructure characteristics, and synergistic strengthening mechanisms

Chengyun Cui et al.

INTERNATIONAL JOURNAL OF PLASTICITY (2018)

Add to Collection

Review Engineering, Chemical

A review of powdered additive manufacturing techniques for Ti-6al-4v biomedical applications

W. S. W. Harun et al.

POWDER TECHNOLOGY (2018)

Add to Collection

Article Engineering, Mechanical

Effect of laser shock peening on elevated temperature residual stress, microstructure and fatigue behavior of ATI 718Plus alloy

Micheal Kattoura et al.

INTERNATIONAL JOURNAL OF FATIGUE (2017)

Add to Collection

Article Multidisciplinary Sciences

High dislocation density-induced large ductility in deformed and partitioned steels

B. B. He et al.

SCIENCE (2017)

Add to Collection

Article Materials Science, Multidisciplinary

An improved prediction of residual stresses and distortion in additive manufacturing

T. Mukherjee et al.

COMPUTATIONAL MATERIALS SCIENCE (2017)

Add to Collection

Article Materials Science, Multidisciplinary

Microstructural response and grain refinement mechanism of commercially pure titanium subjected to multiple laser shock peening impacts

J. Z. Lu et al.

ACTA MATERIALIA (2017)

Add to Collection

Article Materials Science, Multidisciplinary

Combining gradient structure and TRIP effect to produce austenite stainless steel with high strength and ductility

X. L. Wu et al.

ACTA MATERIALIA (2016)

Add to Collection

Article Materials Science, Multidisciplinary

A precipitation-hardened high-entropy alloy with outstanding tensile properties

J. Y. He et al.

ACTA MATERIALIA (2016)

Add to Collection

Article Chemistry, Physical

Microstructure evolution and grain refinement of Ti-6A1-4V alloy by laser shock processing

X. D. Ren et al.

APPLIED SURFACE SCIENCE (2016)

Add to Collection

Article Materials Science, Multidisciplinary

Vacuum heat treatment of iron parts produced by selective laser melting: Microstructure, residual stress and tensile behavior

Bo Song et al.

MATERIALS & DESIGN (2014)

Add to Collection

Article Nanoscience & Nanotechnology

Ultrahigh dense and gradient nano-precipitates generated by warm laser shock peening for combination of high strength and ductility

Chang Ye et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2014)

Add to Collection

Article Physics, Applied

On the role of hierarchical twins for achieving maximum yield strength in nanotwinned metals

Linli Zhu et al.

APPLIED PHYSICS LETTERS (2012)

Add to Collection

Article Nanoscience & Nanotechnology

An atomic and probabilistic perspective on twin nucleation in Mg

J. Wang et al.

SCRIPTA MATERIALIA (2010)

Add to Collection

Article Materials Science, Multidisciplinary

Influence of stacking-fault energy on the accommodation of severe shear strain in Cu-Al alloys during equal-channel angular pressing

Xianghai An et al.

JOURNAL OF MATERIALS RESEARCH (2009)

Add to Collection

Article Nanoscience & Nanotechnology

Influence of microstructure and strain rate on adiabatic shearing behavior in Ti-6Al-4V alloys

Xinqin Liu et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2009)

Add to Collection

Article Engineering, Industrial

Numerical prediction of plastic deformation and residual stresses induced by laser shock processing

AFM Arif

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2003)

Add to Collection

© Peeref 2019-2024. All rights reserved.