☆ 4.7 Article

Microstructures, hot tensile deformation behavior and constitutive modeling in a superlight Mg-2.76Li-3Al-2.6Zn-0.39Y alloy

JOURNAL OF ALLOYS AND COMPOUNDS (2022)

Related references

Note: Only part of the references are listed.

Article Metallurgy & Metallurgical Engineering

Reducing the yield asymmetry in Mg-5Li-3Al-2Zn alloy by hot-extrusion and multi-pass rolling

Xiaoqiang Li et al.

Summary: In this study, a Mg-5Li-3Al-2 Zn (LAZ532) alloy was successfully produced through hot-extrusion and multi-pass rolling, leading to grain refinement, improved mechanical properties, and reduced yield asymmetry. The presence of ultra-fine AlMg4Zn11 and nano Li3Al2 phases in the alloy was observed, contributing to the enhancement of comprehensive mechanical properties. Additionally, the combination of weak basal lamellar texture, grain refinement, and Li element addition effectively improved yield symmetry in the alloy.

JOURNAL OF MAGNESIUM AND ALLOYS (2021)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Effect of rolling ratios on the microstructural evolution and corrosion performance of an as-rolled Mg-8 wt.%Li alloy

B. J. Wang et al.

Summary: The influence of rolling ratios on microstructural changes and corrosion behavior of an as-rolled Mg-8 wt.%Li alloy in 0.1 mol/L NaCl solution was investigated. It was found that as the rolling ratio increased, the alpha-Mg phases elongated and fragmented, leading to decreased corrosion performance. The corrosion process can be divided into two stages, with initial corrosion mainly occurring in beta-Li phases and later transferring to the alpha-Mg phases.

JOURNAL OF MAGNESIUM AND ALLOYS (2021)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Microstructure and corrosion resistance of a duplex structured Mg-7.5Li-3Al-1Zn

Anna Dobkowska et al.

Summary: The study found that the relative composition of Mg-7.5Li-3Al-1Zn alloy changed after extrusion and post-processing annealing, with an increase in beta(Li) content leading to improved corrosion resistance.

JOURNAL OF MAGNESIUM AND ALLOYS (2021)

Add to Collection

Article Chemistry, Physical

Microstructures and mechanical properties of as-extruded Mg-8Gd-2Y-1Zn-6Li alloy

Zijian Yu et al.

Summary: In this study, a high-performance Mg-8Gd-2Y-1Zn-6Li alloy was successfully fabricated, showing significant improvements in yield strength and ultimate tensile strength. The investigation of intermetallic compounds revealed the unique microstructure features and the discovery of a novel island-like beta(1R) phase in Mg-Gd-Li based alloys. These structural components contribute to the high performance of the alloy.

JOURNAL OF ALLOYS AND COMPOUNDS (2021)

Add to Collection

Article Chemistry, Physical

Hot deformation behavior of an extruded AZ31 alloy doped with rare-earth elements

A. Sheikhani et al.

Summary: The study investigated the hot deformation behavior of an extruded Mg-3 wt% Al-1 wt% Zn (AZ31) alloy with and without rare-earth (RE) elements. It was found that the addition of RE elements enhanced the plasticity of the alloy and reduced the instability region according to the processing maps.

JOURNAL OF ALLOYS AND COMPOUNDS (2021)

Add to Collection

Article Nanoscience & Nanotechnology

Hot tensile deformation behavior of extruded LAZ532 alloy with heterostructure

Xiaoqiang Li et al.

Summary: The hot tensile test was performed on an extruded Mg-5Li-3Al-2Zn (LAZ532) alloy with a heterostructure of fibrous extrusion zones (FEZs) and nonfibrous extrusion zones (non-FEZs) coexisted, showing that the alloy exhibited superplastic characteristics at lower strain rates or higher deformation temperatures. The microstructure analysis revealed different deformation behaviors between the FEZs and non-FEZs, with different mechanisms dominating during different stages of deformation. The activation energy was calculated to be around 110.0 kJ/mol, and the hot tensile deformation mechanism involved alternating and coordinated deformation among grain boundary slip, intragranular slip, and dynamic recrystallization (DRX).

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Study of novel, thermally resistant Mg alloy with dual-phase

Yan Tang et al.

Summary: The study found that the addition of ZrO2 resulted in the gradual refinement of the solidified structure of the magnesium alloy, leading to significant improvement in tensile properties after extrusion and annealing. After annealing at high temperature for 8 hours, the alloy's strength remained almost stable, while the plasticity increased, demonstrating good thermal resistance and formability.

MATERIALS SCIENCE AND TECHNOLOGY (2021)

Add to Collection

Article Chemistry, Physical

Simultaneous achievement of high electromagnetic shielding effectiveness (X-band) and strength in Mg-Li-Zn-Gd/MWCNTs composite

Jiahao Wang et al.

Summary: In this study, a Mg-9Li-3Zn-0.5Gd/MWCNTs composite was prepared by a method combining heat treatment, electrophoretic deposition (EPD), and accumulative roll bonding (ARB). The uniformly distributed MWCNTs promoted the precipitation of ultrafine nano-scale W-phase, improving the electrical conductivity, strength, and electromagnetic interference (EMI) shielding effectiveness of the composite material. The enhancement in properties of the composite material was mainly attributed to the dispersion of MWCNTs inducing the precipitation of ultrafine nano-scale W-phase particles.

JOURNAL OF ALLOYS AND COMPOUNDS (2021)

Add to Collection

Article Chemistry, Physical

Synergistically improved damping, elastic modulus and mechanical properties of rolled Mg-8Li-4Y-2Er-2Zn-0.6Zr alloy with twins and long-period stacking ordered phase

Dan Wang et al.

Summary: The Mg-8Li-4Y-2Er-2Zn-0.6Zr alloy exhibits high damping capacity, tensile strength and elastic modulus after heat treatment and cold rolling processes. The introduction of LPSO phase and formation of twins during cold rolling contribute to the improvement in damping capacity and tensile strength. The high elastic modulus of the cold-rolled alloy can be attributed to the effects of LPSO phase and cold rolling.

JOURNAL OF ALLOYS AND COMPOUNDS (2021)

Add to Collection

Article Engineering, Mechanical

Flow characterization of magnesium alloy ZK61 during hot deformation with improved constitutive equations and using activation energy maps

Jinchuan Long et al.

Summary: This study characterized the flow characteristics and workability of as-extruded magnesium alloy ZK61 through isothermal compression tests. Flow stress curves were analyzed, and both conventional and improved Arrhenius constitutive equations were developed to predict flow characteristics. Activation energy maps identified dominant deformation mechanisms and optimal processing conditions for the alloy.

INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2021)

Add to Collection

Article Engineering, Industrial

Extracting HCP Zerilli-Armstrong material parameters for magnesium alloy AZ31B from orthogonal cutting tests

Charbel Y. Seif et al.

Summary: This study presents a methodology to extend Oxley's thick shear zone analysis to HCP materials and successfully extracts Zerilli-Armstrong constitutive equation material parameters for AZ31B from orthogonal cutting tests. By comparing numerical data with experiments, the determined AZ31B material model with updated parameters demonstrated predictability for cutting and thrust forces.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2021)

Add to Collection

Article Nanoscience & Nanotechnology

Size effect of the width of beta-Li phase on the ductility of magnesium?lithium dual-phase alloys

Hanwu Dong et al.

Summary: The study investigates the impact of adding rare earth elements to magnesium-lithium dual-phase alloys on the ductility size effect, finding that the elongation rate is more than two times higher than common magnesium alloys. The improvement in ductility is attributed to the size effect of the width of the β-lithium phase in the alloy, with a critical value within the range of 3-8 micrometers.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2021)

Add to Collection

Article Nanoscience & Nanotechnology

Micromechanical origin of the enhanced ductility in twinless duplex Mg-Li alloy

Di Xie et al.

Summary: Through real-time neutron diffraction measurements, it was found that the enhanced ductility of duplex Mg-Li alloys is attributed to the early yield of BCC beta-Li phase and the sequential activation of basal and pyramidal a slip systems in HCP alpha-Mg phase, which promotes overall work hardening rate and relieves Mises constraint for deformation compatibility. No obvious twinning activities were observed, resulting in symmetric hysteresis loops during a full loading cycle within +/- 1% applied strain.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2021)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Microstructure and mechanical properties of as-cast and solid solution treated Mg-8Li-xAl-yZn alloys

Xin-li Liang et al.

Summary: The Al/Zn ratio significantly affects the microstructure and mechanical properties of Mg-8Li alloy, with solid solution strengthening being the main factor for strength improvement. Among the studied alloys, Mg-8Li-3Al-2Zn alloy after solution treatment at 350°C for 4 hours exhibits the best comprehensive mechanical properties.

TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Effect of Al Addition on Microstructure and Tensile Properties of Mg-8Li-3Al Alloy

Zilong Zhao et al.

Summary: The addition of Al to Mg-8Li alloy results in significant improvement in strength of the alloy, mainly attributed to the precipitation strengthening by Al-Li phase and the orientation of alpha-Mg phase and beta-Li phase.

JOM (2021)

Add to Collection

Article Chemistry, Physical

Role of extrusion temperature on the microstructure evolution and tensile properties of an ultralight Mg-Li-Zn-Er alloy

Hao Ji et al.

Summary: The extrusion temperature plays a significant role in refining the microstructure and affecting the tensile properties of ultralight Mg10Li-5Zn-0.5Er alloy. The increase in extrusion temperature leads to changes in grain size and distribution, as well as variations in strength and elongation.

JOURNAL OF ALLOYS AND COMPOUNDS (2021)

Add to Collection

Article Nanoscience & Nanotechnology

Microstructure evolution and mechanical properties in an ultralight Mg-2.76Li-3Al-2.6Zn-0.39Y alloy

Furong Cao et al.

Summary: A new Mg-Li-Al-Zn-Y alloy was prepared by MDFR to enhance strength and ductility, exhibiting improved mechanical properties with optimized microstructure. The alloy showed a bimodal microstructure after MDFR treatment, contributing to enhanced strength and ductility, while XRD and TEM analysis confirmed the presence of specific phases and compounds.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2021)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Microstructural evolution, flow stress and constitutive modeling of Al-1.88Mg-0.18Sc-0.084Er alloy during hot compression

Fu-rong Cao et al.

Summary: The hot compression behavior and microstructural evolution of fine-grained Al-Mg-Sc-Er alloy wires were investigated, showing that dynamic recovery is the dominant softening mechanism. Continuous dynamic recrystallization and dynamic grain growth were observed at specific temperature and strain rate conditions. The stress exponent and activation energy for deformation suggest that dislocation viscous glide is the main deformation mechanism.

TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2021)

Add to Collection

Article Materials Science, Multidisciplinary

High specific strength Mg-Li-Zn-Er alloy processed by multi deformation processes

Qing Ji et al.

MATERIALS CHARACTERIZATION (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Deformation behavior and texture evolution in an extruded Mg-Li sheet with non-basal texture during tensile deformation

Jun Zhao et al.

MATERIALS CHARACTERIZATION (2020)

Add to Collection

Article Nanoscience & Nanotechnology

Mechanism of phase refinement and its effect on mechanical properties of a severely deformed dual-phase Mg-Li alloy during annealing

Fei Guo et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)

Add to Collection

Article Nanoscience & Nanotechnology

Effect of test temperature on flow behavior and strain hardening of magnesium under high strain rate deformation conditions

Bidyapati Mishra et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)

Add to Collection

Article Nanoscience & Nanotechnology

A simultaneous increase of elastic modulus and ductility by Al and Li additions in Mg-Gd , Zn-Zr-Ag alloy

Teng Tu et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)

Add to Collection

Article Nanoscience & Nanotechnology

Pronounced low-temperature superplasticity of friction stir processed Mg-9Li-1Zn alloy

Mengran Zhou et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)

Add to Collection

Article Nanoscience & Nanotechnology

High strength and plastic deformability of Mg-Li-Al alloy with dual BCC phase produced by a combination of heat treatment and multi-directional forging in channel die

Takahiro Mineta et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)

Add to Collection

Article Nanoscience & Nanotechnology

High temperature deformation behavior of Mg-5wt.%Y binary alloy: Constitutive analysis and processing maps

Nooruddin Ansari et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)

Add to Collection

Article Nanoscience & Nanotechnology

High strain rate compression deformation mechanism and constitutive equation of fine grained Mg-7Gd-5Y-1.2Nd-0.5Zr alloy at different temperatures

Wanru Tang et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)

Add to Collection

Article Metallurgy & Metallurgical Engineering

The modified temperature term on Johnson-Cook constitutive model of AZ31 magnesium alloy with {0002} texture

Feng Zhang et al.

JOURNAL OF MAGNESIUM AND ALLOYS (2020)

Add to Collection

Article Nanoscience & Nanotechnology

Microstructure and mechanical properties of ultra-lightweight Mg-Li-Al/Al-Li composite produced by accumulative roll bonding at ambient temperature

Yang Wang et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)

Add to Collection

Article Chemistry, Physical

Effect of controlled rolling temperature on microstructure and properties of Mg-9Li-1Zn alloy sheet

Yansong Shi et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Hot Compression Behavior of Mg-14Li-6Al-1Ca Alloy

Ryo Tsukane et al.

MATERIALS TRANSACTIONS (2020)

Add to Collection

Article Engineering, Industrial

Microstructure, tensile properties and corrosion behavior of friction stir processed Mg-9Li-1Zn alloy

Gang Liu et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2019)

Add to Collection

Article Nanoscience & Nanotechnology

Mechanical properties and microstructural evolution in a superlight Mg-6.4Li-3.6Zn-0.37A1-0.36Y alloy processed by multidirectional forging and rolling

Furong Cao et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2019)

Add to Collection

Article Nanoscience & Nanotechnology

Investigation on the enhanced maximum strain rate sensitivity (m) superplasticity of Mg-9Li-1Al alloy by a two-step deformation method

H. P. Yang et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2019)

Add to Collection

Article Nanoscience & Nanotechnology

Superplasticity in a multi-directionally forged Mg-Li-Zn alloy

A. Mehrabi et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2019)

Add to Collection

Article Materials Science, Multidisciplinary

The effect of thermal cycling process between high and low temperatures on the microstructure and properties of Mg-10Li-3Al-3Zn-0.25Si alloy

Bin Shao et al.

MATERIALS LETTERS (2019)

Add to Collection

Article Materials Science, Multidisciplinary

Hot Deformation Behavior of LA43M Mg-Li Alloy via Hot Compression Tests

Yi Li et al.

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2019)

Add to Collection

Article Chemistry, Physical

Hot deformation behavior and processing map of a superlight dual-phase Mg-Li alloy

Gang Liu et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2018)

Add to Collection

Article Nanoscience & Nanotechnology

Superplasticity in a commercially extruded ZK30 magnesium alloy

Marta Alvarez-Leal et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2018)

Add to Collection

Article Nanoscience & Nanotechnology

Effects of Sn and Y on the microstructure, texture, and mechanical properties of as-extruded Mg-5Li-3Al-2Zn alloy

Yuehua Sun et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2018)

Add to Collection

Article Nanoscience & Nanotechnology

Low temperature superplasticity of a dual-phase Mg-Li-Zn alloy processed by a multi-mode deformation process

Tianlong Zhang et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2018)

Add to Collection

Article Chemistry, Physical

Microstructure and mechanical properties of the as-cast and warm rolled Mg-9Li-x(Al-Si)-yTi alloys with x=1, 3, 5 and y=0.05 wt.%

JeongTae Kim et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2017)

Add to Collection

Article Chemistry, Physical

Hot deformation of the extruded Mg-10Li-1Zn alloy: Constitutive analysis and processing maps

M. Shalbafi et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2017)

Add to Collection

Article Nanoscience & Nanotechnology

Effect of pre-deformation on microstructure and mechanical properties of WE43 magnesium alloy

Y. H. Kang et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2017)

Add to Collection

Article Nanoscience & Nanotechnology

Superplasticity of a dual-phase-dominated Mg-Li-Al-Zn-Sr alloy processed by multidirectional forging and rolling

Furong Cao et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2017)

Add to Collection

Article Nanoscience & Nanotechnology

Evidence for superplasticity in a CoCrFeNiMn high-entropy alloy processed by high-pressure torsion

Hamed Shahmir et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2017)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Modeling of deformation energy at elevated temperatures and its application in Mg-Li-Al-Y alloy

Fu-rong Cao et al.

TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2017)

Add to Collection

Article Materials Science, Multidisciplinary

Hot tensile deformation behavior and microstructural evolution of a Mg-9.3Li-1.79Al-1.61Zn alloy

Furong Cao et al.

MATERIALS & DESIGN (2016)

Add to Collection

Article Chemistry, Physical

Dynamic recrystallization behavior of Mg-Li-Al-Nd duplex alloy during hot compression

T. C. Xu et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2015)

Add to Collection

Article Nanoscience & Nanotechnology

Effects of high-density pulse current on mechanical properties and microstructure in a rolled Mg-9.3Li-1.79Al-1.61Zn alloy

Furong Cao et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2015)

Add to Collection

Article Materials Science, Multidisciplinary

Superplasticity at Elevated Temperature of a Coarse-Grained Mg-Li Alloy

Kai Lin et al.

ADVANCED ENGINEERING MATERIALS (2014)

Add to Collection

Review Materials Science, Multidisciplinary

Dynamic and post-dynamic recrystallization under hot, cold and severe plastic deformation conditions

Taku Sakai et al.

PROGRESS IN MATERIALS SCIENCE (2014)

Add to Collection

Article Chemistry, Physical

The twin mechanism of Portevin Le Chatelier in Mg-5Li-3Al-1.5Zn-2RE alloy

T. Q. Li et al.

JOURNAL OF ALLOYS AND COMPOUNDS (2011)

Add to Collection

Review Materials Science, Multidisciplinary

A critical review of experimental results and constitutive descriptions for metals and alloys in hot working

Y. C. Lin et al.

MATERIALS & DESIGN (2011)

Add to Collection

Article Materials Science, Multidisciplinary

Material Models for Simulation of Superplastic Mg Alloy Sheet Forming

Eric M. Taleff et al.

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2010)

Add to Collection

Article Nanoscience & Nanotechnology

A modified Johnson-Cook model for tensile behaviors of typical high-strength alloy steel

Y. C. Lin et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2010)

Add to Collection

Article Nanoscience & Nanotechnology

Superplasticity, dynamic grain growth and deformation mechanism in ultra-light two-phase magnesium-lithium alloys

F. R. Cao et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2010)

Add to Collection

Article Nanoscience & Nanotechnology

Microstructural evolution and superplasticity of rolled Mg-9Al-1Zn

T Mohri et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2000)

Add to Collection

© Peeref 2019-2024. All rights reserved.