Related references
Note: Only part of the references are listed.An alternative method to manufacture Ti alloys from particulate materials
L. Bolzoni et al.
POWDER TECHNOLOGY (2021)
Non-isothermal kinetic analysis of high temperature oxidation of Ti-6Al-4V alloy
A. Rajabi et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2020)
Structure and properties of titanium and the Ti-6Al-7Nb alloy after isothermal oxidation
Krzysztof Aniolek
SURFACE ENGINEERING (2020)
Oxidation and Corrosion Behavior of New Low-Cost Ti-7Fe-3Al and Ti-7Fe-5Cr Alloys from Titanium Hydride Powders
Eduardo Reverte et al.
METALS (2020)
The Cyclic Oxidation and Hardness Characteristics of Thermally Exposed Titanium Prepared by Inductive Sintering-Assisted Powder Metallurgy
Fahamsyah H. Latief et al.
CRYSTALS (2020)
Titanium sintering science: A review of atomic events during densification
Randall M. German
INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS (2020)
Hybrid microwave sintering of blended elemental Ti alloys
S. Raynova et al.
JOURNAL OF MANUFACTURING PROCESSES (2019)
Development of Cu-bearing powder metallurgy Ti alloys for biomedical applications
L. Bolzoni et al.
JOURNAL OF THE MECHANICAL BEHAVIOR OF BIOMEDICAL MATERIALS (2019)
Evaluation of reactive induction sintering as a manufacturing route for blended elemental Ti-5Al-2.5Fe alloy
M. T. Jia et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2018)
High-Temperature Oxidation Kinetics and Behavior of Ti-6Al-4V Alloy
Entao Dong et al.
OXIDATION OF METALS (2017)
Powder Metallurgy Strategies to Improve Properties and Processing of Titanium Alloys: A Review
Alexandra Amherd Hidalgo et al.
ADVANCED ENGINEERING MATERIALS (2017)
Prediction of oxidation behavior of near-α titanium alloys
T. Kitashima et al.
SCRIPTA MATERIALIA (2016)
High temperature oxidation resistance in titanium-niobium alloys
B. E. Tegner et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2015)
Development of Al-Nb-B master alloys using Nb and KBF4 Powders
M. Nowak et al.
MATERIALS & DESIGN (2015)
Oxidation and alpha-case formation in Ti-6Al-2Sn-4Zr-2Mo alloy
Raghuveer Gaddam et al.
MATERIALS CHARACTERIZATION (2015)
Assessment of the influence of Al-2Nb-2B master alloy on the grain refinement and properties of LM6 (A413) alloy
L. Bolzoni et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2015)
Isothermal oxidation of Ti-6Al-7Nb alloy
K. Aniolek et al.
VACUUM (2015)
Investigation of the factors influencing the tensile behaviour of PM Ti-3Al-2.5V alloy
L. Bolzoni et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2014)
Microwave Heating, Isothermal Sintering, and Mechanical Properties of Powder Metallurgy Titanium and Titanium Alloys
S. D. Luo et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2013)
COST EFFECTIVE DEVELOPMENTS FOR FABRICATION OF TITANIUM COMPONENTS
M. Ashraf Imam et al.
COST-AFFORDABLE TITANIUM IV (2013)
Influence of vacuum hot-pressing temperature on the microstructure and mechanical properties of Ti-3Al-2.5V alloy obtained by blended elemental and master alloy addition powders
L. Bolzoni et al.
MATERIALS CHEMISTRY AND PHYSICS (2012)
Thermal oxidation of Ti6Al4V alloy: Microstructural and electrochemical characterization
Satendra Kumar et al.
MATERIALS CHEMISTRY AND PHYSICS (2010)
Oxidation of Ti-6Al-4V alloy
Hasan Guleryuz et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2009)
Mechanical biocompatibilities of titanium alloys for biomedical applications
Mitsuo Niinomi
JOURNAL OF THE MECHANICAL BEHAVIOR OF BIOMEDICAL MATERIALS (2008)
Cost-affordable titanium: The component fabrication perspective
F. H. (Sam) Froes et al.
JOM (2007)
Oxidation behaviour of Ti6Al4V titanium alloy in oxygen
MN Mungole et al.
MATERIALS SCIENCE AND TECHNOLOGY (2002)
Resistivity study and computer modelling of the isothermal transformation kinetics of Ti-6Al-4V and Ti-6Al-2Sn-4Zr-2Mo-0.08Si alloys
S Malinov et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2001)
Share Paper
