Related references
Note: Only part of the references are listed.A multiscale investigation into the effect of grain size on void evolution and ductile fracture: Experiments and crystal plasticity modeling
Xiaoqing Shang et al.
INTERNATIONAL JOURNAL OF PLASTICITY (2020)
Modeling of 3D plastic anisotropy and asymmetry of extruded magnesium alloy and its applications in three-point bending
Fei-Fan Li et al.
INTERNATIONAL JOURNAL OF PLASTICITY (2020)
Microstructure, Deformation, and Property of Wrought Magnesium Alloys
J. F. Nie et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2020)
Deformation and Failure Mechanisms in a Magnesium Alloy Under Uniaxial Compressive Loading
Meng Zhao et al.
JOURNAL OF DYNAMIC BEHAVIOR OF MATERIALS (2020)
A Numerical Study of Strain-Rate and Triaxiality Effects in Magnesium Alloys
Shahmeer Baweja et al.
JOURNAL OF DYNAMIC BEHAVIOR OF MATERIALS (2020)
A Concise Note on Deformation Twinning and Spall Failure in Magnesium at the Extremes
C. L. Williams et al.
JOURNAL OF DYNAMIC BEHAVIOR OF MATERIALS (2020)
A Brief Review of Spall Failure in Pure and Alloyed Magnesium
D. D. Mallick et al.
JOURNAL OF DYNAMIC BEHAVIOR OF MATERIALS (2020)
Investigation into the Extrudability of a New Mg-Al-Zn-RE Alloy with Large Amounts of Alloying Elements
Sheng-Wen Bai et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2019)
Fracture of an anisotropic rare-earth-containing magnesium alloy (ZEK100) at different stress states and strain rates: Experiments and modeling
Saadi A. Habib et al.
INTERNATIONAL JOURNAL OF PLASTICITY (2019)
Void growth and coalescence in a magnesium alloy studied by synchrotron radiation laminography
Babak Kondori et al.
ACTA MATERIALIA (2018)
Fracture prediction based on a two-surface plasticity law for the anisotropic magnesium alloys AZ31 and ZE10
Jeong-Yeon Lee et al.
INTERNATIONAL JOURNAL OF PLASTICITY (2018)
Damage and failure at negative stress triaxialities: Experiments, modeling and numerical simulations
Michael Bruenig et al.
INTERNATIONAL JOURNAL OF PLASTICITY (2018)
Experimental fracture characterisation of an anisotropic magnesium alloy sheet in proportional and non-proportional loading conditions
A. Abedini et al.
INTERNATIONAL JOURNAL OF SOLIDS AND STRUCTURES (2018)
Notched specimen under compression for ductile failure criteria
Petr Kubik et al.
MECHANICS OF MATERIALS (2018)
Establishment and verification of two-component ductile fracture criteria with high estimation accuracy
Fei-Fan Li et al.
ENGINEERING FRACTURE MECHANICS (2018)
An improved curvature method of detecting the onset of localized necking in Marciniak tests and its extension to Nakazima tests
Junying Min et al.
INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2017)
New biaxially loaded specimens for the analysis of damage and fracture in sheet metals
Steffen Gerke et al.
INTERNATIONAL JOURNAL OF SOLIDS AND STRUCTURES (2017)
Three dimensional simulations of texture and triaxiality effects on the plasticity of magnesium alloys
Balaji Selvarajou et al.
ACTA MATERIALIA (2017)
Experimental study on the mechanical properties of AZ31B-H24 magnesium alloy sheets under various loading conditions
Yueqian Jia et al.
INTERNATIONAL JOURNAL OF FRACTURE (2016)
Failure of metals I: Brittle and ductile fracture
A. Pineau et al.
ACTA MATERIALIA (2016)
Calibration of ductile fracture criteria at negative stress triaxiality
Petr Kubik et al.
INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2016)
On plastic flow in notched hexagonal close packed single crystals
Balaji Selvarajou et al.
JOURNAL OF THE MECHANICS AND PHYSICS OF SOLIDS (2016)
Ductile fracture of aluminum 2024-T351 under proportional and non-proportional multi-axial loading: Bao-Wierzbicki results revisited
Jessica Papasidero et al.
INTERNATIONAL JOURNAL OF SOLIDS AND STRUCTURES (2015)
Micromechanically-motivated phenomenological Hosford-Coulomb model for predicting ductile fracture initiation at low stress triaxialities
Dirk Mohr et al.
INTERNATIONAL JOURNAL OF SOLIDS AND STRUCTURES (2015)
On the notch ductility of a magnesium-rare earth alloy
B. Kondori et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2015)
Determination of the Effect of Stress State on the Onset of Ductile Fracture Through Tension-Torsion Experiments
J. Papasidero et al.
EXPERIMENTAL MECHANICS (2014)
Modeling of shear ductile fracture considering a changeable cut-off value for stress triaxiality
Yanshan Lou et al.
INTERNATIONAL JOURNAL OF PLASTICITY (2014)
Asymmetric yield function based on the stress invariants for pressure sensitive metals
Jeong Whan Yoon et al.
INTERNATIONAL JOURNAL OF PLASTICITY (2014)
Measuring forming limit strains with digital image correlation analysis
Kaifeng Wang et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2014)
The role of deformation twinning in the fracture behavior and mechanism of basal textured magnesium alloys
D. Ando et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2014)
Effect of Stress Triaxiality on the Flow and Fracture of Mg Alloy AZ31
Babak Kondori et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2014)
A new approach for ductile fracture prediction on Al 2024-T351 alloy
Akhtar S. Khan et al.
INTERNATIONAL JOURNAL OF PLASTICITY (2012)
Application of extended Mohr-Coulomb criterion to ductile fracture
Yuanli Bai et al.
INTERNATIONAL JOURNAL OF FRACTURE (2010)
Hybrid experimental-numerical analysis of basic ductile fracture experiments for sheet metals
Matthieu Dunand et al.
INTERNATIONAL JOURNAL OF SOLIDS AND STRUCTURES (2010)
Anisotropic hardening and non-associated flow in proportional loading of sheet metals
Thomas B. Stoughton et al.
INTERNATIONAL JOURNAL OF PLASTICITY (2009)
Anisotropic ductile fracture Part I: experiments
AA Benzerga et al.
ACTA MATERIALIA (2004)
Anisotropic ductile fracture Part II: theory
AA Benzerga et al.
ACTA MATERIALIA (2004)
On fracture locus in the equivalent strain and stress triaxiality space
YB Bao et al.
INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2004)
A non-associated flow rule for sheet metal forming
TB Stoughton
INTERNATIONAL JOURNAL OF PLASTICITY (2002)
Share Paper
