Related references
Note: Only part of the references are listed.Review of z-pinned laminates and sandwich composites
A. P. Mouritz
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2020)
Tensile Properties of Z-Pin Reinforced Laminates with Circumferentially Notched Z-Pins
Andre Knopp et al.
JOURNAL OF COMPOSITES SCIENCE (2020)
Mechanical properties of composite laminates reinforced with rectangular z-pins in monotonic and cyclic tension
Julian Hoffmann et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2018)
Effect of Z-pinning on the impact resistance of composite laminates with different layups
L. Francesconi et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2018)
Compression properties of composite laminates reinforced with rectangular z-pins
Julian Hoffmann et al.
COMPOSITES SCIENCE AND TECHNOLOGY (2018)
Mode I delamination fatigue resistance of unidirectional and quasi-isotropic composite laminates reinforced with rectangular z-pins
Julian Hoffmann et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2018)
Preparation of Carbon Fiber Powder-Coated Z-Pins and Experimental Study on the Mode I Delamination Toughening Properties
Xiao-Xu Wang et al.
POLYMER COMPOSITES (2016)
Micro-mechanical finite element analysis of Z-pins under mixed-mode loading
B. Zhang et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2015)
A novel model of delamination bridging via Z-pins in composite laminates
G. Allegri et al.
INTERNATIONAL JOURNAL OF SOLIDS AND STRUCTURES (2014)
Effect of z-pin surface treatment on delamination and debonding properties of z-pinned composite laminates
Andre Knopp et al.
JOURNAL OF MATERIALS SCIENCE (2014)
Flexural properties of z-pinned composite laminates in seawater environment
Andre Knopp et al.
JOURNAL OF MATERIALS SCIENCE (2014)
Prediction of permanent indentation due to impact on laminated composites based on an elasto-plastic model incorporating fiber failure
Wei He et al.
COMPOSITE STRUCTURES (2013)
Impact and post-impact properties of cfrp laminates reinforced with rectangular z-pins
Matthias Knaupp et al.
COMPOSITES SCIENCE AND TECHNOLOGY (2013)
Compression fatigue properties of z-pinned quasi-isotropic carbon/epoxy laminate with barely visible impact damage
M. D. Isa et al.
COMPOSITE STRUCTURES (2011)
Multi-level analysis of low-cost Z-pinned composite joints Part 1: Single Z-pin behaviour
Javier Toral Vazquez et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2011)
A mechanistic interpretation of the comparative in-plane mechanical properties of 3D woven, stitched and pinned composites
A. P. Mouritz et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2010)
Compression properties of z-pinned composite laminates
A. P. Mouritz
COMPOSITES SCIENCE AND TECHNOLOGY (2007)
Flexural properties of z-pinned laminates
P. Chang et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2007)
Improvement of low-velocity impact and compression-after-impact performance by z-fibre pinning
X. Zhang et al.
COMPOSITES SCIENCE AND TECHNOLOGY (2006)
Delamination of Z-pinned carbon fibre reinforced laminates
DDR Cartié et al.
COMPOSITES SCIENCE AND TECHNOLOGY (2006)
Properties and failure mechanisms of z-pinned laminates in monotonic and cyclic tension
P. Chang et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2006)
Compression after impact of thin composite laminates
S Sanchu-Saez et al.
COMPOSITES SCIENCE AND TECHNOLOGY (2005)
Snubbing effects in the pullout of a fibrous rod from a laminate
BN Cox
MECHANICS OF ADVANCED MATERIALS AND STRUCTURES (2005)
Experimental study on z-pin bridging law by pullout test
SC Dai et al.
COMPOSITES SCIENCE AND TECHNOLOGY (2004)
Mode II delamination toughness of z-pinned laminates\
WY Yan et al.
COMPOSITES SCIENCE AND TECHNOLOGY (2004)
Mechanisms of crack bridging by composite and metallic rods
DDR Cartie et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2004)
Mixed mode delamination of polymer composite laminates reinforced through the thickness by z-fibers
KL Rugg et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2002)
Share Paper
