Related references
Note: Only part of the references are listed.Reverse piezo-resistivity of 3D printed continuous carbon fiber/PA6 composites in a low stress range
Keisuke Iizuka et al.
ADVANCED COMPOSITE MATERIALS (2021)
Reinforcing in the lay-up direction with self-heating for carbon fiber composites fabricated using a fused filament fabrication 3D printer
Akira Todoroki et al.
COMPOSITE STRUCTURES (2021)
Fibre misalignment and breakage in 3D printing of continuous carbon fibre reinforced thermoplastic composites
Haoqi Zhang et al.
ADDITIVE MANUFACTURING (2021)
Tensile property evaluations of 3D printed continuous carbon fiber reinforced thermoplastic composites
Akira Todoroki et al.
ADVANCED COMPOSITE MATERIALS (2020)
Mechanism of folding a fiber bundle in the curved section of 3D printed carbon fiber reinforced plastics
Hirohide Shiratori et al.
ADVANCED COMPOSITE MATERIALS (2020)
Progressive damage simulation for a 3D-printed curvilinear continuous carbon fiber-reinforced thermoplastic based on continuum damage mechanics
Naruki Ichihara et al.
ADVANCED COMPOSITE MATERIALS (2020)
3D printing of optimized composites with variable fiber volume fraction and stiffness using continuous fiber
Kentaro Sugiyama et al.
COMPOSITES SCIENCE AND TECHNOLOGY (2020)
3D compaction printing of a continuous carbon fiber reinforced thermoplastic
Masahito Ueda et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2020)
3D printed continuous CF/PA6 composites: Effect of microscopic voids on mechanical performance
Qinghao He et al.
COMPOSITES SCIENCE AND TECHNOLOGY (2020)
Three-dimensionally printed designable joint for carbon fibre reinforced plastics
Yoichiro Koga et al.
ADVANCED COMPOSITE MATERIALS (2019)
Bending fracture rule for 3D-printed curved continuous-fiber composite
Kouki Ishii et al.
ADVANCED COMPOSITE MATERIALS (2019)
Tensile properties and failure behavior of chopped and continuous carbon fiber composites produced by additive manufacturing
Juan Naranjo-Lozada et al.
ADDITIVE MANUFACTURING (2019)
Elastic properties of 3D printed fibre-reinforced structures
Haider Al Abadi et al.
COMPOSITE STRUCTURES (2018)
Characterization of mechanical properties and fracture mode of additively manufactured carbon fiber and glass fiber reinforced thermoplastics
G. D. Goh et al.
MATERIALS & DESIGN (2018)
Additive manufacturing of woven carbon fibre polymer composites
Andrew N. Dickson et al.
COMPOSITE STRUCTURES (2018)
Effects of Set Curvature and Fiber Bundle Size on the Printed Radius of Curvature by a Continuous Carbon Fiber Composite 3D Printer
Ryosuke Matsuzaki et al.
ADDITIVE MANUFACTURING (2018)
An investigation into 3D printing of fibre reinforced thermoplastic composites
L. G. Blok et al.
ADDITIVE MANUFACTURING (2018)
Piezoresistive effect of plain-weave CFRP fabric subjected to cyclic loading
Yusuke Nishio et al.
ADVANCED COMPOSITE MATERIALS (2017)
Evaluation of carbon fiber-embedded 3D printed structures for strengthening and structural-health monitoring
Xinhua Yao et al.
MATERIALS & DESIGN (2017)
Experimental characterization and micrography of 3D printed PLA and PLA reinforced with short carbon fibers
Rafael Thiago Luiz Ferreira et al.
COMPOSITES PART B-ENGINEERING (2017)
Interface and performance of 3D printed continuous carbon fiber reinforced PLA composites
Xiaoyong Tian et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2016)
Three-dimensional printing of continuous-fiber composites by in-nozzle impregnation
Ryosuke Matsuzaki et al.
SCIENTIFIC REPORTS (2016)
Impact-damage visualization in CFRP by resistive heating: Development of a new detection method for indentations caused by impact loads
Yoshiro Suzuki et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2012)
Damage detection of carbon fiber reinforced polymer composites via electrical resistance measurement
Jie Wen et al.
COMPOSITES PART B-ENGINEERING (2011)
Piezoresistivity of unidirectional carbon/epoxy composites for multiaxial loading
Akira Todoroki et al.
COMPOSITES SCIENCE AND TECHNOLOGY (2009)
Self-sensing of flexural strain and damage in carbon fiber polymer-matrix composite by electrical resistance measurement
Shoukai Wang et al.
CARBON (2006)
Electrical resistance change of unidirectional CFRP due to applied load
A Todoroki et al.
JSME INTERNATIONAL JOURNAL SERIES A-SOLID MECHANICS AND MATERIAL ENGINEERING (2004)
The electrical resistance response of continuous carbon fibre composite laminates to mechanical strain
N Angelidis et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2004)
Mechanical damage and strain in carbon fiber thermoplastic-matrix composite, sensed by electrical resistivity measurement
Z Mei et al.
POLYMER COMPOSITES (2002)
Measurement of orthotropic electric conductance of CFRP laminates and analysis of the effect on delamination monitoring with an electric resistance change method
A Todoroki et al.
COMPOSITES SCIENCE AND TECHNOLOGY (2002)
A comparative investigation of electrical resistance and acoustic emission during cyclic loading of CFRP laminates
T Prasse et al.
COMPOSITES SCIENCE AND TECHNOLOGY (2001)
Share Paper
