Related references
Note: Only part of the references are listed.Cold-Rolling Strain Hardening Effect on the Microstructure, Serration-Flow Behaviour and Dislocation Density of Friction Stir Welded AA5083
Zainuddin Sajuri et al.
METALS (2020)
Microstructural and ageing response assessment of eutectic Al-Cu alloy due to isothermal heat treatment in semisolid state
Abhimanyu Chaudhari et al.
MATERIALS RESEARCH EXPRESS (2020)
Microstructure evolution and mechanical properties of double-sided friction stir welding between AA6061-T6 and AA7075-T651
Ashu Garg et al.
CIRP JOURNAL OF MANUFACTURING SCIENCE AND TECHNOLOGY (2020)
Hot-wire GTAW cladding: inconel 625 on 347 stainless steel
Bishal Silwal et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2019)
Effect of post-weld heat treatment on the mechanical behavior and dislocation density of friction stir welded Al6061
Amir Hossein Baghdadi et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2019)
Effect of Severe Plastic Deformation on the Conductivity and Strength of Copper-Clad Aluminium Conductors
Rimma Lapovok et al.
METALS (2019)
Accumulative Roll Bonding-A Review
Seyed Mahmoud Ghalehbandi et al.
APPLIED SCIENCES-BASEL (2019)
Effect of Process Parameters on Interfacial Bonding Properties of Aluminium-Copper Clad Sheet Processed by Multi-Pass Friction Stir-Welding Technique
Nora Osman et al.
METALS (2019)
Overview of thin film deposition techniques
Olayinka Oluwatosin Abegunde et al.
AIMS MATERIALS SCIENCE (2019)
Effect of Heat Input on the Mechanical Behaviour of Al-Cu FSW Lap Joints
Aldoni Gabriel Wiedenhoft et al.
MATERIALS RESEARCH-IBERO-AMERICAN JOURNAL OF MATERIALS (2018)
Optimization of flux-cored arc welding process parameters by using genetic algorithm
B. Senthilkumar et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2017)
Production of wire reinforced composite materials through explosive welding
B. Gulenc et al.
ARCHIVES OF CIVIL AND MECHANICAL ENGINEERING (2016)
Influence of heat input on weld bead geometry using duplex stainless steel wire electrode on low alloy steel specimens
Ajit Mondal et al.
COGENT ENGINEERING (2016)
Effects of parameter optimization on microstructure and properties of GTAW clad welding on AISI 304L stainless steel using Inconel 52M
Chun-Ming Lin et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2015)
Interfacial microstructure and properties of copper clad steel produced using friction stir welding versus gas metal arc welding
Z. Shen et al.
MATERIALS CHARACTERIZATION (2015)
Comparison of energy consumption and environmental impact of friction stir welding and gas metal arc welding for aluminum
Amber Shrivastava et al.
CIRP JOURNAL OF MANUFACTURING SCIENCE AND TECHNOLOGY (2015)
Investigation on dissimilar underwater friction stir lap welding of 6061-T6 aluminum alloy to pure copper
Jingqing Zhang et al.
MATERIALS & DESIGN (2014)
Hardfacing using ferro-alloy powder mixtures by submerged arc welding
Ramin Zahiri et al.
SURFACE & COATINGS TECHNOLOGY (2014)
Microstructure and Phase Constitution Near the Interface of Explosively Welded Aluminum/Copper Plates
Henryk Paul et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2013)
Enhancing metallurgical and mechanical properties of friction stir lap welding of Al-Cu using intermediate layer
M. Akbari et al.
SCIENCE AND TECHNOLOGY OF WELDING AND JOINING (2013)
Electrical, Corrosion, and Mechanical Properties of Aluminum-Copper Joints Produced by Explosive Welding
Mustafa Acarer
JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2012)
Al-to-Cu Friction Stir Lap Welding
Vahid Firouzdor et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2012)
Effect of materials position on friction stir lap welding of Al to Cu
M. Akbari et al.
SCIENCE AND TECHNOLOGY OF WELDING AND JOINING (2012)
Review on Laser Deposition Welding: From Micro to Macro
Stefan Kaierle et al.
LASER ASSISTED NET SHAPE ENGINEERING 7 (LANE 2012) (2012)
Brittleness study of intermetallic (Cu, Al) layers in copper-clad aluminium thin wires
E. Hug et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2011)
Effect of process parameters on clad bead geometry and its shape relationships of stainless steel claddings deposited by GMAW
T. Kannan et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2010)
Deposition of Multicomponent Alloys on Low-Carbon Steel Using Gas Tungsten Arc Welding (GTAW) Cladding Process
Jie H. Chen et al.
MATERIALS TRANSACTIONS (2009)
Microstructural and mechanical properties of friction stir welded aluminum/copper lap joints
A. Abdollah-Zadeh et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2008)
Modelling of the effects of welding conditions on dilution of stainless steel claddings produced by gas metal arc welding procedures
A. S. Shahi et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2008)
Friction stir processing technology: A review
Z. Y. Ma
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2008)
Development of mathematical models for prediction of weld bead geometry in cladding by flux cored arc welding
P. K. Palani et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2006)
Microstructure and wear property of Fe-Mn-Cr-Mo-V alloy cladding by submerged arc welding
SP Lu et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2004)
High-productivity multiple-wire submerged-arc welding and cladding with metal-powder addition
J Tusek et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2003)
Microstructures and mechanical properties of ultra low carbon IF steel processed by accumulative roll bonding process
SH Lee et al.
MATERIALS TRANSACTIONS (2002)
Share Paper
