Related references
Note: Only part of the references are listed.Machinability analysis of nickel-based superalloy Nimonic 90: a comparison between wet and LCO2 as a cryogenic coolant
Tej Patel et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2021)
Effect of cryogenic and wet coolant performance on drilling of super duplex stainless steel (2507)
T. Kanagaraju et al.
MATERIALS EXPRESS (2020)
Evaluation of tool wear, surface roughness/topography and chip morphology when machining of Ni-based alloy 625 under MQL, cryogenic cooling and CryoMQL
Cagri Vakkas Yildirim et al.
JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2020)
Effect of LN2 and CO2 coolants in milling of 55NiCrMoV7 steel
M. Jebaraj et al.
JOURNAL OF MANUFACTURING PROCESSES (2020)
Analysis of EN24 steel in turning process with copper nanofluids under minimum quantity lubrication
M. Naresh Babu et al.
JOURNAL OF THE BRAZILIAN SOCIETY OF MECHANICAL SCIENCES AND ENGINEERING (2019)
A novel method of assessing and predicting coated cutting tool wear during Inconel DA 718 turning
S. Capasso et al.
WEAR (2019)
Machining-induced grain refinement of AISI 4340 alloy steel under dry and cryogenic conditions
Natasha A. Raof et al.
JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2019)
Performance Analysis of Machining Ti-6Al-4V Under Cryogenic CO2 Using PVD-TiN Coated Tool
K. Nimel Sworna Ross et al.
JOURNAL OF FAILURE ANALYSIS AND PREVENTION (2019)
Comparative evaluations of machining performance during turning of 17-4 PH stainless steel under cryogenic and wet machining conditions
P. Sivaiah et al.
MACHINING SCIENCE AND TECHNOLOGY (2018)
Friction and wear behaviour of cemented carbide tool materials sliding against Al2O3 and Si3N4 ceramics under dry condition
Wenbin Ji et al.
CERAMICS INTERNATIONAL (2018)
Comparative Assessment on Machinability Aspects of AISI 4340 Alloy Steel Using Uncoated Carbide and Coated Cermet Inserts During Hard Turning
Anshuman Das et al.
ARABIAN JOURNAL FOR SCIENCE AND ENGINEERING (2016)
Analytical temperature prediction for cutting steel
Mustapha Abouridouane et al.
CIRP ANNALS-MANUFACTURING TECHNOLOGY (2016)
Microhardness and Surface Integrity in Turning Process of Duplex Stainless Steel (DSS) for Different Cutting Conditions
G. Krolczyk et al.
JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2014)
Performance and wear mechanisms of whisker-reinforced alumina, coated and uncoated PCBN tools when high-speed turning aged Inconel 718
Volodymyr Bushlya et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2013)
Experimental comparison of carbon-dioxide and liquid nitrogen cryogenic coolants in turning of AISI 1045 steel
B. Dilip Jerold et al.
CRYOGENICS (2012)
Effect of cutting parameters in the surface residual stresses generated by turning in AISI 4340 steel
Virginia Garcia Navas et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2012)
State of the art in hard turning
Gaurav Bartarya et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2012)
Friction and wear behaviors of WC/Co cemented carbide tool materials with different WC grain sizes at temperatures up to 600 °C
Deng Jianxin et al.
INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS (2012)
Machinability investigations on hardened AISI 4340 steel using coated carbide insert
R. Suresh et al.
INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS (2012)
Experimental investigations on machinability aspects in finish hard turning of AISI 4340 steel using uncoated and multilayer coated carbide inserts
Ashok Kumar Sahoo et al.
MEASUREMENT (2012)
Wear mechanisms of cemented carbide tools in dry cutting of precipitation hardening semi-austenitic stainless steels
Deng Jianxin et al.
WEAR (2011)
Experimental investigation of turning AISI 1045 steel using cryogenic carbon dioxide as the cutting fluid
B. Dilip Jerold et al.
Journal of Manufacturing Processes (2011)
Wear mechanisms of WC-Co cutting tools from high-speed tribological tests
T. Kagnaya et al.
WEAR (2009)
Investigation of tool wear and cutting force in cryogenic machining using design of experiments
K. V. B. S. Kalyan Kumar et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2008)
Accuracy of hard turning
J. Kundrak et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2008)
Cutting temperature, tool wear, surface roughness and dimensional deviation in turning AISI-4037 steel under cryogenic condition
N. R. Dhar et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2007)
Heat generation and temperature prediction in metal cutting: A review and implications for high speed machining
N. A. Abukhshim et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2006)
Hard turning: AISI 4340 high strength low alloy steel and AISI D2 cold work tool steel
JG Lima et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2005)
Surface integrity in finish hard turning of case-hardened steels
J Rech et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2003)
Cutting conditions for finish turning process aiming: the use of dry cutting
AE Diniz et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2002)
Machining of AISI 4140 steel under cryogenic cooling-tool wear, surface roughness and dimensional deviation
NR Dhar et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2002)
The influence of cryogenic cooling on tool wear, dimensional accuracy and surface finish in turning AISI 1040 and E4340C steels
NR Dhar et al.
WEAR (2001)
Beneficial effects of cryogenic cooling over dry and wet machining on tool wear and surface finish in turning AISI 1060 steel
S Paul et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2001)
Cooling approaches and cutting temperatures in cryogenic machining of Ti-6Al-4V
SY Hong et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2001)
Ecological aspects of the cutting fluids and its influence on quantifiable parameters of the cutting processes
M Sokovic et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2001)
Dry machining: Machining of the future
PS Sreejith et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2000)
Share Paper
