Related references
Note: Only part of the references are listed.Vat photopolymerization 3D printing for advanced drug delivery and medical device applications
Xiaoyan Xu et al.
JOURNAL OF CONTROLLED RELEASE (2021)
The economics of additive manufacturing: Towards a general cost model including process failure
Jin Ding et al.
INTERNATIONAL JOURNAL OF PRODUCTION ECONOMICS (2021)
Development of Conductive Gelatine-Methacrylate Inks for Two-Photon Polymerisation
Paola Sanjuan-Alberte et al.
POLYMERS (2021)
Residual polymer stabiliser causes anisotropic electrical conductivity during inkjet printing of metal nanoparticles
Gustavo F. Trindade et al.
COMMUNICATIONS MATERIALS (2021)
Recent Advances in Enabling Technologies in 3D Printing for Precision Medicine
Margaret E. Prendergast et al.
ADVANCED MATERIALS (2020)
A cost model for the economic evaluation of in-situ monitoring tools in metal additive manufacturing
Bianca Maria Colosimo et al.
INTERNATIONAL JOURNAL OF PRODUCTION ECONOMICS (2020)
Curing behavior of a UV-curable inkjet ink: Distinction between surface-cure and deep-cure performance
Jonas Simon et al.
JOURNAL OF APPLIED POLYMER SCIENCE (2020)
Improvement on curing performance and morphology of E5I/TPGDA mixture in a free radical-cationic hybrid photopolymerization system
Ran Liu et al.
JOURNAL OF POLYMER RESEARCH (2020)
On the Network Topology of Cross-Linked Acrylate Photopolymers: A Molecular Dynamics Case Study
John J. Karnes et al.
JOURNAL OF PHYSICAL CHEMISTRY B (2020)
A Reactive Prodrug Ink Formulation Strategy for Inkjet 3D Printing of Controlled Release Dosage Forms and Implants
Yinfeng He et al.
ADVANCED THERAPEUTICS (2020)
Foamable acrylic based ink for the production of light weight parts by inkjet-based 3D printing
A. Wagner et al.
EUROPEAN POLYMER JOURNAL (2019)
A compact LED-based projection microstereolithography for producing 3D microstructures
Ebrahim Behroodi et al.
SCIENTIFIC REPORTS (2019)
Cost modeling and analysis for Mask Image Projection Stereolithography additive manufacturing: Simultaneous production with mixed geometries
Yiran Yang et al.
INTERNATIONAL JOURNAL OF PRODUCTION ECONOMICS (2018)
A new photocrosslinkable polycaprolactone-based ink for three-dimensional inkjet printing
Yinfeng He et al.
JOURNAL OF BIOMEDICAL MATERIALS RESEARCH PART B-APPLIED BIOMATERIALS (2017)
3D printing of tablets using inkjet with UV photoinitiation
Elizabeth A. Clark et al.
INTERNATIONAL JOURNAL OF PHARMACEUTICS (2017)
An investigation into the depth and time dependent behavior of UV cured 3D ink jet printed objects
X. Chen et al.
JOURNAL OF MATERIALS RESEARCH (2017)
Flax fiber-reinforced composite lattice cores: A low-cost and recyclable approach
Jun Xu et al.
MATERIALS & DESIGN (2017)
One-step volumetric additive manufacturing of complex polymer structures
Maxim Shusteff et al.
SCIENCE ADVANCES (2017)
3D Inkjet Printing of Electronics Using UV Conversion
Ehab Saleh et al.
ADVANCED MATERIALS TECHNOLOGIES (2017)
A Critical Review on Recent Research Methodologies in Additive Manufacturing
M. Srinivas et al.
MATERIALS TODAY-PROCEEDINGS (2017)
Paper-Based Inkjet-Printed Flexible Electronic Circuits
Yan Wang et al.
ACS APPLIED MATERIALS & INTERFACES (2016)
Novel inkjet droplet method generating monodisperse hollow metal oxide micro-spheres
Woo Jin Shin et al.
CHEMICAL ENGINEERING JOURNAL (2016)
Inkjet printing of UV-curable adhesive and dielectric inks for microfluidic devices
E. M. Hamad et al.
LAB ON A CHIP (2016)
The cost of additive manufacturing: machine productivity, economies of scale and technology-push
Martin Baumers et al.
TECHNOLOGICAL FORECASTING AND SOCIAL CHANGE (2016)
Effect of droplet sizes on evaporation of a bi-component droplet at DME (dimethyl ether)/n-heptane-fueled engine conditions
Dehao Ju et al.
ENERGY (2015)
Inkjet printing for pharmaceutics - A review of research and manufacturing
Ronan Daly et al.
INTERNATIONAL JOURNAL OF PHARMACEUTICS (2015)
Compact polymeric 3D prints of high stability
Goetz Peter Hellmann et al.
JOURNAL OF MATERIALS RESEARCH (2014)
Photochemistry and Radical Chemistry under Low Intensity Visible Light Sources: Application to Photopolymerization Reactions
Jacques Lalevee et al.
MOLECULES (2014)
Complex heterogeneous tissue constructs containing multiple cell types prepared by inkjet printing technology
Tao Xu et al.
BIOMATERIALS (2013)
Kinetic modeling of bulk free-radical polymerization of methyl methacrylate
Vladislav Jaso et al.
POLYMER JOURNAL (2013)
Three-dimensional inkjet biofabrication based on designed images
Kenichi Arai et al.
BIOFABRICATION (2011)
Effects of photointensity gradient on directional crystal growth in blends of crystalline polymer and photoreactive monomer undergoing photopolymerization-induced phase transformation
Pankaj Rathi et al.
JOURNAL OF CHEMICAL PHYSICS (2009)
Spatial and temporal evolution of the photoinitiation rate for thick polymer systems illuminated by polychromatic light: selection of efficient photoinitiators for LED or mercury lamps
Nicole Stephenson Kenning et al.
POLYMER INTERNATIONAL (2008)
Cytotoxicity of denture base acrylic resins: A literature review
JH Jorge et al.
JOURNAL OF PROSTHETIC DENTISTRY (2003)
Electron-beam initiated polymerization of acrylate compositions 3: compared reactivity of hexanediol and tripropyleneglycol diacrylates under UV or EB initiation
C Patacz et al.
RADIATION PHYSICS AND CHEMISTRY (2001)
Cure depth in photopolymerization: Experiments and theory
JH Lee et al.
JOURNAL OF MATERIALS RESEARCH (2001)
Influence of UV radiation wavelength on conversion and temperature distribution profiles within dimethacrylate thick material during photopolymerization
L Lecamp et al.
POLYMER (2001)
Share Paper
