Related references
Note: Only part of the references are listed.Machining of SiC ceramic matrix composites: A review
Qinglong An et al.
CHINESE JOURNAL OF AERONAUTICS (2021)
Numerical model of unidirectional CFRP in machining: Development of an amended friction model
Jie Xu et al.
COMPOSITE STRUCTURES (2021)
Study on Burr Formation and Tool Wear in Drilling CFRP and Its Hybrid Composites
Jeong Hwan Lee et al.
APPLIED SCIENCES-BASEL (2021)
Removal mechanism of CFRP by laser multi direction interaction
L. Y. Xu et al.
OPTICS AND LASER TECHNOLOGY (2021)
Damage behaviors of unidirectional CFRP in orthogonal cutting: A comparison between single- and multiple-pass strategies
Hao Nan Li et al.
COMPOSITES PART B-ENGINEERING (2020)
Orthogonal cutting of UD-CFRP using multiscale analysis: Finite element modeling
Amira Hassouna et al.
JOURNAL OF COMPOSITE MATERIALS (2020)
Investigation on particle motions and resultant impact erosion on quartz crystals by the micro-particle laden waterjet and airjet
Li Zhang et al.
POWDER TECHNOLOGY (2020)
Simulation of edge impact and compression after edge impact in CFRP laminates
A. Arteiro et al.
COMPOSITE STRUCTURES (2020)
A quantitative analysis of the transition of fracture mechanisms of Ti6Al4V over a wide range of stress triaxiality and strain rate
Bing Wang et al.
ENGINEERING FRACTURE MECHANICS (2020)
Multiscale simulation of grain refinement induced by dynamic recrystallization of Ti6Al4V alloy during high speed machining
Xiang Xu et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2020)
The relationship between the mechanical properties and microstructures of carbon fibers
Wang Mei-ling et al.
NEW CARBON MATERIALS (2020)
A study of energy dissipating mechanisms in orthogonal cutting of UD-CFRP composites
Xiaoye Yan et al.
COMPOSITE STRUCTURES (2019)
Improved analytical prediction of burr formation in micro end milling
Xuewei Zhang et al.
INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2019)
Micro-mechanics based cohesive zone modeling of full scale ductile plate tearing: From initiation to steady-state
R. G. Andersen et al.
INTERNATIONAL JOURNAL OF SOLIDS AND STRUCTURES (2019)
Effect of cutter geometry on machining induced damage in orthogonal cutting of UD polymer composites: FE study
F. Cepero-Mejias et al.
COMPOSITE STRUCTURES (2019)
A review on machining of carbon fiber reinforced ceramic matrix composites
Jinguang Du et al.
CERAMICS INTERNATIONAL (2019)
The fatigue of carbon fibre reinforced plastics - A review
Parvez Alam et al.
COMPOSITES PART B-ENGINEERING (2019)
Force coefficient prediction for drilling of UD-CFRP based on FEM simulation of orthogonal cutting
Xiaoye Yan et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2019)
Elimination of delamination and burr formation using high-frequency vibration-assisted drilling of hybrid CFRP/Ti6Al4V stacked material
R. Hussein et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2019)
On the periodicity of fixed-abrasive planetary lapping based on a generic model
Hao Nan Li et al.
JOURNAL OF MANUFACTURING PROCESSES (2019)
Finite element modeling of friction at the tool-chip-workpiece interface in high speed machining of Ti6Al4V
Maohua Du et al.
INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2019)
Experimental study on the improvement of surface integrity of tungsten steel using acoustic levitation polishing
Huan Qi et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2018)
A micro-scale cutting model for UD CFRP composites with thermo-mechanical coupling
Hui Cheng et al.
COMPOSITES SCIENCE AND TECHNOLOGY (2017)
Modelling the orthogonal cutting of UD-CFRP composites: Development of a novel cohesive zone model
Alessandro Abena et al.
COMPOSITE STRUCTURES (2017)
Biocompatibility and Inflammatory Potential of Titanium Alloys Cultivated with Human Osteoblasts, Fibroblasts and Macrophages
Jana Markhoff et al.
MATERIALS (2017)
Numerical studies of frictional responses when cutting hybrid CFRP/Ti composite
Jinyang Xu et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2016)
Delamination analysis of woven fabrication laminates using cohesive zone model
Mohsen Moslemi et al.
JOURNAL OF CENTRAL SOUTH UNIVERSITY (2016)
Numerical Modeling of Stacked Composite CFRP/Ti Machining under Different Cutting Sequence Strategies
Jinyang Xu et al.
INTERNATIONAL JOURNAL OF PRECISION ENGINEERING AND MANUFACTURING (2016)
Potential-based constitutive models for cohesive interfaces: Theory, implementation and examples
M. Leuschner et al.
COMPOSITES PART B-ENGINEERING (2015)
Cutting modeling using cohesive zone concept of titanium/CFRP composite stacks
Jinyang Xu et al.
INTERNATIONAL JOURNAL OF PRECISION ENGINEERING AND MANUFACTURING (2015)
Finite element modeling of microstructural changes in dry and cryogenic cutting of Ti6Al4V alloy
Giovanna Rotella et al.
CIRP ANNALS-MANUFACTURING TECHNOLOGY (2014)
Numerical contribution to the comprehension of saw-toothed Ti6Al4V chip formation in orthogonal cutting
F. Ducobu et al.
INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2014)
Finite Element Modeling of Cutting Force and Chip Formation During Thermally Assisted Machining of Ti6Al4V Alloy
Yao Xi et al.
JOURNAL OF MANUFACTURING SCIENCE AND ENGINEERING-TRANSACTIONS OF THE ASME (2013)
A review on the tensile properties of natural fiber reinforced polymer composites
H. Ku et al.
COMPOSITES PART B-ENGINEERING (2011)
Occurrence and propagation of delamination during the machining of carbon fibre reinforced plastics (CFRPs) - An experimental study
Wolfgang Hintze et al.
COMPOSITES SCIENCE AND TECHNOLOGY (2011)
Modified material constitutive models for serrated chip formation simulations and experimental validation in machining of titanium alloy Ti-6Al-4V
Mohammad Sima et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2010)
Micro-mechanical modeling of machining of FRP composites - Cutting force analysis
G. Venu Gopala Rao et al.
COMPOSITES SCIENCE AND TECHNOLOGY (2007)