☆ 4.5 Article

Early Crack Propagation in Single Tooth Bending Fatigue: Combination of Finite Element Analysis and Critical-Planes Fatigue Criteria

METALS (2021)

Related references

Note: Only part of the references are listed.

Article Engineering, Multidisciplinary

Gear root bending strength: statistical treatment of Single Tooth Bending Fatigue tests results Conference Proceedings

Luca Bonaiti et al.

Summary: Gear tooth failure due to tooth root bending fatigue is one of the most dangerous failure modes in gears, precise definition of gear bending fatigue strength is crucial for calculating gear component service life, Maximum Likelihood Estimation can be used to estimate the S-N curve from experimental points, symmetrical configuration STBF test can consider the survival of a single tooth.

FORSCHUNG IM INGENIEURWESEN-ENGINEERING RESEARCH (2021)

Add to Collection

Article Engineering, Mechanical

A scuffing model for spur gear contacts

Sheng Li et al.

Summary: This study introduces a scuffing model for spur gear contacts and conducts simulations to demonstrate the influences of surface roughness and rotational speed on scuffing load.

MECHANISM AND MACHINE THEORY (2021)

Add to Collection

Article Chemistry, Multidisciplinary

Tooth Root Bending Strength of Gears: Dimensional Effect for Small Gears Having a Module below 5 mm

Franco Concli

Summary: This paper investigates the tooth root bending load-carrying capacity of small gears and proposes an extended formula for the size factor Y-X based on ISO 6336.

APPLIED SCIENCES-BASEL (2021)

Add to Collection

Article Engineering, Mechanical

Gear Root Bending Strength: A Comparison Between Single Tooth Bending Fatigue Tests and Meshing Gears

Luca Bonaiti et al.

Summary: Gear tooth breakage due to bending fatigue is a dangerous failure mode, and the precise definition of tooth bending strength is crucial in gear design. Single tooth bending fatigue tests are commonly used to study this failure mode, but when designing gear sets, the actual loading conditions and strength of meshing gears must be taken into consideration.

JOURNAL OF MECHANICAL DESIGN (2021)

Add to Collection

Article Chemistry, Multidisciplinary

Bending Fatigue Behavior of 17-4 PH Gears Produced by Additive Manufacturing

Franco Concli et al.

Summary: The introduction of Additive Manufacturing is changing the way components and machines are designed and manufactured. This study presents experimental results on gear samples made with 17-4 PH produced via Laser Powder Bed Fusion, determining fatigue limits using statistical approaches and comparing data with ISO standards. Additional SEM analyses were conducted to investigate material behavior and possible defects in tested gears.

APPLIED SCIENCES-BASEL (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Gear Root Bending Strength: A New Multiaxial Approach to Translate the Results of Single Tooth Bending Fatigue Tests to Meshing Gears

Franco Concli et al.

Summary: A method for calculating fkorr using numerical simulations with a multiaxial fatigue criterion was proposed in this study. It was found that fkorr varies with gear geometrical characteristics, material fatigue strength, and load ratio set in STBF tests. Additionally, fkorr was observed to increase with the ratio between the bending and torsional fatigue limits, and have an effect on determining the critical point where fracture nucleates.

METALS (2021)

Add to Collection

Article Engineering, Mechanical

A rotating gear test methodology for evaluation of high-cycle tooth bending fatigue lives under fully reversed and fully released loading conditions

Isaac J. Hong et al.

INTERNATIONAL JOURNAL OF FATIGUE (2020)

Add to Collection

Article Engineering, Mechanical

Investigations on the tooth root bending strength and the fatigue fracture characteristics of case-carburized and shot-peened gears of different sizes

K. J. Winkler et al.

PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART C-JOURNAL OF MECHANICAL ENGINEERING SCIENCE (2019)

Add to Collection

Article Materials Science, Multidisciplinary

Tooth Root Bending Fatigue Strength of High-Density Sintered Small-Module Spur Gears: The Effect of Porosity and Microstructure

Vigilio Fontanari et al.

METALS (2019)

Add to Collection

Review Materials Science, Multidisciplinary

A Review on Micropitting Studies of Steel Gears

Huaiju Liu et al.

COATINGS (2019)

Add to Collection

Proceedings Paper Engineering, Mechanical

Fatigue behaviour of gear teeth made of case hardened steel: from competing mechanisms to lifetime variability

Vincent Argoud et al.

FATIGUE DESIGN 2019, INTERNATIONAL CONFERENCE ON FATIGUE DESIGN, 8TH EDITION (2019)

Add to Collection

Article Engineering, Mechanical

Contact and bending fatigue behaviour of austempered ductile iron gears

Carlo Gorla et al.

PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART C-JOURNAL OF MECHANICAL ENGINEERING SCIENCE (2018)

Add to Collection

Proceedings Paper Engineering, Mechanical

Austempered Ductile Iron (ADI) for gears: Contact and bending fatigue behavior

Franco Concli

AIAS2017 - 46TH CONFERENCE ON STRESS ANALYSIS AND MECHANICAL ENGINEERING DESIGN (2018)

Add to Collection

Article Engineering, Mechanical

A comparison of bending fatigue strength of carburized and nitrided gears for industrial applications

Edoardo Conrado et al.

ENGINEERING FAILURE ANALYSIS (2017)

Add to Collection

Article Engineering, Multidisciplinary

Bending Fatigue Failure of a Helical Pinion Bevel Gear

George A. Pantazopoulos

JOURNAL OF FAILURE ANALYSIS AND PREVENTION (2015)

Add to Collection

Article Engineering, Mechanical

Bending and contact fatigue strength of innovative steels for large gears

Carlo Gorla et al.

PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART C-JOURNAL OF MECHANICAL ENGINEERING SCIENCE (2014)

Add to Collection

Article Engineering, Mechanical

The mean stress effect on the high-cycle fatigue strength from a multiaxial fatigue point of view

L Susmel et al.

INTERNATIONAL JOURNAL OF FATIGUE (2005)

Add to Collection

Article Engineering, Mechanical

Influence of shot peening on bending tooth fatigue limit of case hardened gears

M Benedetti et al.

INTERNATIONAL JOURNAL OF FATIGUE (2002)

Add to Collection

© Peeref 2019-2024. All rights reserved.