Related references
Note: Only part of the references are listed.Coupled thermomechanical analysis of fused deposition using the finite element method
Jingyi Wang et al.
FINITE ELEMENTS IN ANALYSIS AND DESIGN (2021)
Mechanisms of Nucleation and Solid-Solid-Phase Transitions in Triblock Janus Assemblies
Hossein Eslami et al.
JOURNAL OF CHEMICAL THEORY AND COMPUTATION (2021)
Optimisation of Strength Properties of FDM Printed Parts-A Critical Review
Daniyar Syrlybayev et al.
POLYMERS (2021)
Prediction of part distortion in Fused Deposition Modelling (FDM) of semi-crystalline polymers via COMSOL: Effect of printing conditions
Anto Antony Samy et al.
CIRP JOURNAL OF MANUFACTURING SCIENCE AND TECHNOLOGY (2021)
Colloidal Lignin Particles and Epoxies for Bio-Based, Durable, and Multiresistant Nanostructured Coatings
Karl Alexander Henn et al.
ACS APPLIED MATERIALS & INTERFACES (2021)
Voxelization modelling based finite element simulation and process parameter optimization for Fused Filament Fabrication
Yong Zhou et al.
MATERIALS & DESIGN (2020)
Modelling of the temperature and residual stress fields during 3D printing of polymer composites
A. El Moumen et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2019)
Minimizing warpage of ABS prototypes built with low-cost fused deposition modeling machine using developed closed-chamber and optimal process parameters
Chil-Chyuan Kuo et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2019)
Finite Element Analysis of Additive Manufacturing Based on Fused Deposition Modeling: Distortions Prediction and Comparison With Experimental Data
Alberto Cattenone et al.
JOURNAL OF MANUFACTURING SCIENCE AND ENGINEERING-TRANSACTIONS OF THE ASME (2019)
Multi-Material Additive Manufacturing of Sustainable Innovative Materials and Structures
Rupinder Singh et al.
POLYMERS (2019)
Evaluation of additive manufacturing technologies for dimensional and geometric accuracy
Abdulrahman Al-Ahmari et al.
INTERNATIONAL JOURNAL OF MATERIALS & PRODUCT TECHNOLOGY (2019)
Tensile properties and failure behavior of chopped and continuous carbon fiber composites produced by additive manufacturing
Juan Naranjo-Lozada et al.
ADDITIVE MANUFACTURING (2019)
Analysis of Thermomechanical Properties of Selected Class of Recycled Thermoplastic Materials Based on Their Applications
Job Momanyi et al.
RECYCLING (2019)
Warpage of FDM parts: Experimental tests and analytic model
Antonio Armillotta et al.
ROBOTICS AND COMPUTER-INTEGRATED MANUFACTURING (2018)
The Influence of Manufacturing Parameters on the Mechanical Behaviour of PLA and ABS Pieces Manufactured by FDM: A Comparative Analysis
Adrian Rodriguez-Panes et al.
MATERIALS (2018)
Taguchi based process optimization for dimension and tolerance control for fused deposition modelling
Shahrain Mahmood et al.
ADDITIVE MANUFACTURING (2018)
Performance evaluation of warping characteristic of fused deposition modelling process
Biranchi N. Panda et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2017)
Creep Behavior of ABS Polymer in Temperature-Humidity Conditions
Teagen An et al.
JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2017)
Research on Warpage Deformation Mechanism & Control Method of Fused Deposition Parts
Linlin Liu et al.
ADVANCED GRAPHIC COMMUNICATIONS AND MEDIA TECHNOLOGIES (2017)
Layer-by-layer assembled hydrophobic coatings for cellulose nanofibril films and textiles, made of polylysine and natural wax particles
Nina Forsman et al.
CARBOHYDRATE POLYMERS (2017)
An investigation on distortion of PLA thin-plate part in the FDM process
Liu Xinhua et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2015)
Influence of the average surface roughness on the formation of superhydrophobic polymer surfaces through spin-coating with hydrophobic fumed silica
Cagla Kosak Soz et al.
POLYMER (2015)
Thermal conditions affecting heat transfer in FDM/FFE: a contribution towards the numerical modelling of the process This paper investigates convection, conduction and radiation phenomena in the filament deposition process
S. F. Costa et al.
VIRTUAL AND PHYSICAL PROTOTYPING (2015)
An Additive Manufacturing Test Artifact
Shawn Moylan et al.
JOURNAL OF RESEARCH OF THE NATIONAL INSTITUTE OF STANDARDS AND TECHNOLOGY (2014)
Research on the Interlayer Stress and Warpage Deformation in FDM
Peng Anhua
MATERIALS PROCESSING TECHNOLOGY II, PTS 1-4 (2012)
On the Thermal Expansion Behavior of Polystyrene/Polyethyleneterephthalate Blend Systems: Experimental Study
Fares D. Alsewailem
JOURNAL OF THERMOPLASTIC COMPOSITE MATERIALS (2009)
Improving dimensional accuracy of Fused Deposition Modelling processed part using grey Taguchi method
Anoop Kumar Sood et al.
MATERIALS & DESIGN (2009)
A model research for prototype warp deformation in the FDM process
Tian-Ming Wang et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2007)
Three-dimensional finite element analysis simulations of the fused deposition modelling process
Y. Zhang et al.
PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE (2006)
Thermal properties of melt polymers by the hot wire technique
WN dos Santos
POLYMER TESTING (2005)
Rapid fabrication of a non-assembly robotic hand with embedded components
KJ De Laurentis et al.
ASSEMBLY AUTOMATION (2004)
Critical parameters influencing the quality of prototypes in fused deposition modelling
R Anitha et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2001)
Share Paper
