Related references
Note: Only part of the references are listed.Design guidelines for laser additive manufacturing of lightweight structures in TiAl6V4
J. Kranz et al.
JOURNAL OF LASER APPLICATIONS (2015)
Rough surfaces with enhanced heat transfer for electronics cooling by direct metal laser sintering
Luigi Ventola et al.
INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER (2014)
Design optimization of supports for overhanging structures in aluminum and titanium alloys by selective laser melting
F. Calignano
MATERIALS & DESIGN (2014)
An Additive Manufacturing Test Artifact
Shawn Moylan et al.
JOURNAL OF RESEARCH OF THE NATIONAL INSTITUTE OF STANDARDS AND TECHNOLOGY (2014)
Design for Additive Manufacturing-Element transitions and aggregated structures
Guido A. O. Adama et al.
CIRP JOURNAL OF MANUFACTURING SCIENCE AND TECHNOLOGY (2014)
Influence of process parameters on surface roughness of aluminum parts produced by DMLS
F. Calignano et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2013)
From Powders to Dense Metal Parts: Characterization of a Commercial AlSiMg Alloy Processed through Direct Metal Laser Sintering
Diego Manfredi et al.
MATERIALS (2013)
Optimal part orientation in Rapid Manufacturing process for achieving geometric tolerances
Ratnadeep Paul et al.
JOURNAL OF MANUFACTURING SYSTEMS (2011)
Speed and accuracy evaluation of additive manufacturing machines
Tomaz Brajlih et al.
RAPID PROTOTYPING JOURNAL (2011)
A computing method for accurate slice contours based on an STL model
Jibin Zhao et al.
VIRTUAL AND PHYSICAL PROTOTYPING (2009)
Computer aided rapid tooling process selection and manufacturability evaluation for injection mold development
Nagahanumaiah et al.
COMPUTERS IN INDUSTRY (2008)
A benchmark study on rapid prototyping processes and machines: quantitative comparisons of mechanical properties, accuracy, roughness, speed, and material cost
G. D. Kim et al.
PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE (2008)
Qualification of rapid prototyping tools: proposition of a procedure and a test part
Dominique Scaravetti et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2008)
Selective laser melting of heat transfer devices
Matthew Wong et al.
RAPID PROTOTYPING JOURNAL (2007)
Direct laser sintering of metal powders: Mechanism, kinetics and microstructural features
A. Simchi
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2006)
An approach to minimize build errors in direct metal laser sintering
Y Ning et al.
IEEE TRANSACTIONS ON AUTOMATION SCIENCE AND ENGINEERING (2006)
Effect and control of hatch length on material properties in the direct metal laser sintering process
Y Ning et al.
PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE (2005)
Benchmarking for comparative evaluation of RP systems and processes
M Mahesh et al.
RAPID PROTOTYPING JOURNAL (2004)
Fabrication and structural performance of periodic cellular metal sandwich structures
HNG Wadley et al.
COMPOSITES SCIENCE AND TECHNOLOGY (2003)
Slicing procedures in layered manufacturing: a review
PM Pandey et al.
RAPID PROTOTYPING JOURNAL (2003)
Surface roughness visualisation for rapid prototyping models
RI Campbell et al.
COMPUTER-AIDED DESIGN (2002)
Direct selective laser sintering of hard metal powders: Experimental study and simulation
XC Wang et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2002)
A generic part orientation system based on volumetric error in rapid prototyping
SH Masood et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2002)
Modelling and optimisation of Rapid Prototyping
SH Choi et al.
COMPUTERS IN INDUSTRY (2002)
A volumetric approach to part-build orientations in rapid prototyping
W Rattanawong et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2001)
Manufacturability analysis of flatness tolerances in Solid Freeform Fabrication
R Arni et al.
JOURNAL OF MECHANICAL DESIGN (2001)
Adaptive direct slicing of the solid model for rapid prototyping
ZW Zhao et al.
INTERNATIONAL JOURNAL OF PRODUCTION RESEARCH (2000)
Share Paper
