☆ 4.6 Article

Porous Biomass Carbon Derived from Clivia miniata Leaves via NaOH Activation for Removal of Dye

MATERIALS (2022)

Related references

Note: Only part of the references are listed.

Article Chemistry, Physical

Adsorption of cationic dyes onto chemically modified activated carbon: Kinetics and thermodynamic study

Mariam Sh Gohr et al.

Summary: In this study, activated carbon was successfully modified by carboxylic group via mechanical attrition in the presence of NaOH and chloroacetic acid. The modified activated carbon showed excellent adsorption performance for methylene blue and crystal violet dyes and achieved equilibrium within 15 minutes. The adsorption isotherms of both dyes were described by the Langmuir model, and the kinetics followed the pseudo-second-order model. The thermodynamic analysis suggested that the adsorption of the organic dyes was endothermic and spontaneous. The modified activated carbon demonstrated acceptable removal efficiency for the two dyes over five cycles.

JOURNAL OF MOLECULAR LIQUIDS (2022)

Add to Collection

Article Agricultural Engineering

Conversion of wheat husk to high surface area activated carbon for energy storage in high-performance supercapacitors

Mutawara Mahmood Baig et al.

Summary: The study demonstrates the potential utilization of wheat husks derived activated carbon as electrode material for supercapacitors, showing excellent electrochemical properties. The process used is simple, environmentally friendly, and could significantly reduce the biomass wastes from wheat husks.

BIOMASS & BIOENERGY (2021)

Add to Collection

Article Chemistry, Physical

Influence of mixed alkali on the preparation of edible fungus substrate porous carbon material and its application for the removal of dye

Siji Chen et al.

Summary: In this study, three porous carbon materials derived from edible fungus substrate waste were prepared using different alkalis as activators, showing that mixed alkali (MA) could serve as an efficient activator. The prepared materials exhibited changes in surface area and pore structure, and demonstrated high adsorption capacities for the model dye Rhodamine B, with MA-treated material having the highest capacity.

COLLOIDS AND SURFACES A-PHYSICOCHEMICAL AND ENGINEERING ASPECTS (2021)

Add to Collection

Article Engineering, Chemical

Multi-component separation of small molecular/ionic pollutants with smart pH-gating membranes

Mei-Ling Liu et al.

Summary: A smart pH-gating membrane with tunable and reversible molecular sieving architectures was reported for precise separation of multicomponent mixtures. This membrane exhibited a high dye molecule-to-NaCl selectivity, showing promising applications for selective separation and recovery of valuable products.

CHEMICAL ENGINEERING SCIENCE (2021)

Add to Collection

Article Chemistry, Physical

Investigation of dye removal ability and reusability of green and sustainable silica and carbon-silica hybrid aerogels prepared from paddy waste ash

Dilsad Dolunay Eslek Koyuncu et al.

Summary: In this study, paddy waste ash was used to produce carbon-silica hybrid and silica aerogels, with improved pore structure and dye removal performance. The adsorption experiments showed that the dye removal efficiency correlated with the zeta potential curve of the samples, indicating the importance of surface charge.

COLLOIDS AND SURFACES A-PHYSICOCHEMICAL AND ENGINEERING ASPECTS (2021)

Add to Collection

Article Biochemistry & Molecular Biology

Adsorption of Malachite Green and Alizarin Red S Dyes Using Fe-BTC Metal Organic Framework as Adsorbent

Giulia Rossella Delpiano et al.

Summary: Synthetic organic dyes are commonly used in various industrial sectors but are also harmful water pollutants. In recent years, research has focused on developing materials for the removal of dyes from water, particularly nanostructured adsorbent materials like Metal Organic Frameworks (MOFs). This study found that an iron-based Fe-BTC MOF showed good results in adsorbing alizarin red S and malachite green dyes, achieving rapid adsorption equilibrium.

INTERNATIONAL JOURNAL OF MOLECULAR SCIENCES (2021)

Add to Collection

Article Engineering, Chemical

Adsorption of diclofenac on mesoporous activated carbons: Physical and chemical activation, modeling with genetic programming and molecular dynamic simulation

Seyyed Abbas Mirzaee et al.

Summary: The study focused on the preparation of activated carbon from Astragalus Mongholicus for diclofenac adsorption, showing that AC-700°C had the highest efficiency. The adsorption mechanisms involved electrostatic interaction, cation-pi interaction, and pi-pi electron interaction.

CHEMICAL ENGINEERING RESEARCH & DESIGN (2021)

Add to Collection

Article Engineering, Chemical

Pinch-based targeting methodology for multi-contaminant material recycle/reuse

Hon Huin Chin et al.

Summary: This work introduces a systematic resource targeting procedure in the domain of multiple contaminants water recycling/reuse network. A resource-allocation model is developed and modified to obtain the optimal solution, providing insights into the problem while offering the minimum resource target.

CHEMICAL ENGINEERING SCIENCE (2021)

Add to Collection

Article Engineering, Chemical

Preparation of porous nitrogen-doped activated carbon derived from rice straw for high-performance supercapacitor application

Kanruethai Charoensook et al.

Summary: Biomass-derived porous activated carbon with high surface area and nitrogen functional groups were prepared for supercapacitor application using rice straw as the precursor. The nitrogen-doped AC exhibited excellent capacitance performance and cycling stability under evaluation. Ionic liquid electrolyte enabled higher energy density to be achieved.

JOURNAL OF THE TAIWAN INSTITUTE OF CHEMICAL ENGINEERS (2021)

Add to Collection

Review Chemistry, Physical

A State-of-the-Art Review on Innovative Geopolymer Composites Designed for Water and Wastewater Treatment

Ismail Luhar et al.

Summary: The use of geopolymer composites as adsorbents in wastewater treatment offers an innovative and sustainable solution, with their porous structure, excellent physical and chemical stability, and environmental friendliness. These materials effectively eliminate hazardous pollutants, promoting sustainable water resource utilization. Research on the performance and application of geopolymers in water and wastewater treatment is gaining increasing attention from researchers worldwide.

MATERIALS (2021)

Add to Collection

Article Chemistry, Physical

Recovery of Waste Polyurethane from E-Waste. Part II. Investigation of the Adsorption Potential for Wastewater Treatment

Vincenzo Santucci et al.

Summary: This study investigated the performance of waste polyurethane foam (PUF) derived from end-of-life refrigerators as an adsorbent for wastewater treatment. The results showed that the adsorption capacity of waste PUF was limited for methylene blue and mercury, and much lower for phenol, with removal efficiency lower than that of commercial activated carbon (AC). The preliminary results suggest that additional pre-treatments are needed to overcome the adsorption limits of waste PUF for better wastewater treatment.

MATERIALS (2021)

Add to Collection

Article Chemistry, Physical

Activated Graphene Oxide-Calcium Alginate Beads for Adsorption of Methylene Blue and Pharmaceuticals

Burcu Gunes et al.

Summary: The study prepared crosslinked calcium alginate-graphene oxide beads and activated them for removal of organic pollutants, showing high adsorption capacities and adaptability. The activated beads exhibited good adsorption performance, with fitting accuracy and thermodynamic parameters playing important roles in the adsorption process.

MATERIALS (2021)

Add to Collection

Article Chemistry, Physical

Sustainable Development of Magnetic Chitosan Core-Shell Network for the Removal of Organic Dyes from Aqueous Solutions

Karthik Rathinam et al.

Summary: The study focused on the removal of alizarin red S (ARS) dye using a magnetic chitosan core-shell network (MCN). The synthesized MCN showed effective removal of ARS dye, reaching equilibrium after 60 min, with pH playing a major role. The results also indicated that electrostatic interactions dominated the removal of ARS dye under acidic conditions.

MATERIALS (2021)

Add to Collection

Article Chemistry, Physical

Solketal Removal from Aqueous Solutions Using Activated Carbon and a Metal-Organic Framework as Adsorbents

Leticia Santamaria et al.

Summary: This study investigated the adsorption of solketal using two different commercial adsorbents, activated carbon and a metal-organic framework. The results showed that activated carbon was more effective in removing solketal from aqueous solutions than the metal-organic framework.

MATERIALS (2021)

Add to Collection

Article Chemistry, Physical

Functionalization of Zeolite NaP1 for Simultaneous Acid Red 18 and Cu(II) Removal

Tomasz Bien et al.

Summary: The study found that the pseudo second order kinetic model and Langmuir isotherm were the best fit for the NaP1CS sorbent, with acidic pH being the optimal condition for removal. The thermodynamic parameters and desorption process were also discussed in the research.

MATERIALS (2021)

Add to Collection

Article Chemistry, Physical

Removal of Heavy Metal Ions from One- and Two-Component Solutions via Adsorption on N-Doped Activated Carbon

Justyna Kazmierczak-Razna et al.

Summary: This study found that activated carbons modified with nitrogen functional groups exhibit a higher capacity for heavy metal ion adsorption, with adsorption increasing with solution concentration and contact time. The optimal pH for adsorption was determined to be 8.0 for Cu(II) and 6.0 for Zn(II), with Langmuir isotherm providing a better fit to the experimental data than the Freundlich isotherm. The kinetic data was better described by the pseudo-second order model.

MATERIALS (2021)

Add to Collection

Article Biotechnology & Applied Microbiology

Porous carbon materials based on Physalis alkekengi L. husk and its application for removal of malachite green

Bolun Zhang et al.

Summary: PCPH, a porous carbon material prepared from Physalis alkekengi L. husk (PH), exhibited excellent surface properties with a high specific surface area and total pore volume. The adsorption performance of PCPH, especially towards Malachite Green, was studied, showing high adsorption capacity and potential application in environmental water pollution treatment.

ENVIRONMENTAL TECHNOLOGY & INNOVATION (2021)

Add to Collection

Article Green & Sustainable Science & Technology

Sustainable Durio zibethinus-Derived Biosorbents for Congo Red Removal from Aqueous Solution: Statistical Optimization, Isotherms and Mechanism Studies

A. A. Oyekanmi et al.

Summary: This study investigated the biosorption mechanism of Congo Red dyes using acid-treated durian peels, showing that under optimal conditions of pH 5.5, contact time 105 min, initial concentration 212.5 mg L-1, at 45 degrees C, the durian peels achieved 95.2% removal of CR. The experimental data fitted well to the second order polynomial model and the Langmuir isotherm model, indicating a biosorption capacity of 107.52 mg g(-1) and spontaneous adsorption of CR dyes.

SUSTAINABILITY (2021)

Add to Collection

Article Engineering, Environmental

Disassembly of lignocellulose into cellulose, hemicellulose, and lignin for preparation of porous carbon materials with enhanced performances

Siji Chen et al.

Summary: The disassembly of lignocellulosic biomass into cellulose, hemicellulose, and lignin was found to be an effective strategy for preparing various porous carbon materials with enhanced performances, as demonstrated by the higher adsorption capacities of the designed materials compared to most adsorbents and even graphite oxide.

JOURNAL OF HAZARDOUS MATERIALS (2021)

Add to Collection

Article Green & Sustainable Science & Technology

Recycled reverse osmosis membrane combined with pre-oxidation for improved arsenic removal from high turbidity waters and retrofit of conventional drinking water treatment process

Victor Rezende Moreira et al.

Summary: The study shows that end-of-life reverse osmosis membranes can be recycled through low-cost oxidative treatment, offering higher efficiency in removing arsenic, iron, and manganese from contaminated surface water compared to ultrafiltration modules. Despite lower permeate flux and shorter lifespan, the process presents lower operating costs and higher return on investment, while also having environmental benefits.

JOURNAL OF CLEANER PRODUCTION (2021)

Add to Collection

Article Engineering, Environmental

Adsorption of pharmaceuticals in a fixed-bed column using tyre-based activated carbon: Experimental investigations and numerical modelling

Farzaneh Feizi et al.

Summary: The research demonstrated differences in adsorption capacity for PRO, CIP and CLO under different conditions; ATC showed higher adsorption capacity after thermal and chemical activation; the Hydrus-1D model performed better in simulating pharmaceutical transport.

JOURNAL OF HAZARDOUS MATERIALS (2021)

Add to Collection

Article Biotechnology & Applied Microbiology

Preparation of biomass carbon material based on Fomes fomentarius via alkali activation and its application for the removal of brilliant green in wastewater

Yuhan Xia et al.

Summary: Fungal hyphae from Fomes fomentarius were utilized for the preparation of biomass carbon material for the first time, showing excellent adsorption capacity and cycling stability. BCFF-Na4-700-60 exhibited a large specific surface area and high pore volume, making it a potential adsorbent for wastewater treatment in the dyeing industry.

ENVIRONMENTAL TECHNOLOGY & INNOVATION (2021)

Add to Collection

Article Engineering, Environmental

Carbon dioxide capture from flue gas in biochar produced from spent coffee grounds: Effect of surface chemistry and porous structure

Alivia Mukherjee et al.

Summary: This study evaluated the effects of different pyrolysis temperatures and heating rates on slow-pyrolysis of spent coffee grounds to produce biochar, as well as the impact on biochar's surface properties, reactivity, and surface functionalities. The results showed that SCG-600 has potential advantages in CO2 adsorption capacity, surface composition, and functional groups.

JOURNAL OF ENVIRONMENTAL CHEMICAL ENGINEERING (2021)

Add to Collection

Proceedings Paper Materials Science, Multidisciplinary

Synthesis and characterization of GO-Ag nanocomposite for removal of malachite dye from aqueous solution

Akil Ahmad et al.

Summary: The graphene-silver oxide nanocomposite (GO-Ag) was successfully synthesized and used for the removal of malachite green from aqueous solution, showing promising adsorption efficiency under various experimental conditions. The adsorption capacity of MG on GO-Ag was found to be 65.21 mg/g at pH 8. Freundlich model and pseudo-second order kinetic model were identified as the best fit for the adsorption process of malachite green onto GO-Ag nanocomposite.

MATERIALS TODAY-PROCEEDINGS (2021)

Add to Collection

Article Engineering, Environmental

Comparative study on methylene blue adsorption behavior of coffee husk-derived activated carbon materials prepared using hydrothermal and soaking methods

Thi Hien Tran et al.

Summary: Coffee husk in Vietnam can be utilized to produce activated carbon with high adsorption capacity for pollutants through hydrothermal carbonization. The activated carbon obtained showed significantly increased surface area and improved adsorption capacity for methylene blue compared to raw hydrochar. The activated carbon materials exhibited promising potential as sorbents for the removal of pollutants from aqueous solutions.

JOURNAL OF ENVIRONMENTAL CHEMICAL ENGINEERING (2021)

Add to Collection

Proceedings Paper Materials Science, Multidisciplinary

Effects of physical activation on pore textures and heavy metals removal of fiber-based activated carbons

Muhammad Abbas Ahmad Zaini et al.

Summary: Fiber-based activated carbons prepared through steam activation exhibit high specific surface area and microporous structure, enabling effective removal of heavy metals such as copper and lead.

MATERIALS TODAY-PROCEEDINGS (2021)

Add to Collection

Article Chemistry, Multidisciplinary

Effect of carbon-rich biochar on mechanical properties of PLA-biochar composites

Kamonwan Aup-Ngoen et al.

SUSTAINABLE CHEMISTRY AND PHARMACY (2020)

Add to Collection

Article Engineering, Environmental

Waste biomass-derived oxygen and nitrogen co-doped porous carbon/MgO composites as superior acetone adsorbent: Experimental and DFT study on the adsorption behavior

Ke Zhou et al.

CHEMICAL ENGINEERING JOURNAL (2020)

Add to Collection

Review Environmental Sciences

Lignocellulose-based adsorbents: A spotlight review of the effective parameters on carbon dioxide capture process

Zahra Rouzitalab et al.

CHEMOSPHERE (2020)

Add to Collection

Article Chemistry, Physical

Adsorption of dimethyl sulfide from model fuel on raw and modified activated carbon from walnut and pistachio shell origins: Kinetic and thermodynamic study

Hossein Jalilvand et al.

COLLOIDS AND SURFACES A-PHYSICOCHEMICAL AND ENGINEERING ASPECTS (2020)

Add to Collection

Article Chemistry, Physical

Effective adsorption of chloroanilines from aqueous solution by m-phenylenediamine modified hyper-cross-linked resin: Kinetic, equilibrium, and thermodynamic studies

Zongtang Liu et al.

COLLOIDS AND SURFACES A-PHYSICOCHEMICAL AND ENGINEERING ASPECTS (2020)

Add to Collection

Article Chemistry, Analytical

N/O co-doped interlinked porous carbon nanoflakes derived from soybean stalk for high-performance supercapacitors

Yun-Peng Zhao et al.

JOURNAL OF ELECTROANALYTICAL CHEMISTRY (2020)

Add to Collection

Article Agricultural Engineering

Pretreatment of corn stover via sodium hydroxide–urea solutions to improve the glucose yield

Lianyue Shao et al.

BIORESOURCE TECHNOLOGY (2020)

Add to Collection

Article Engineering, Environmental

Hierarchical porous carbon fabricated from cellulose-degrading fungus modified rice husks: Ultrahigh surface area and impressive improvement in toluene adsorption

Hairong Cheng et al.

JOURNAL OF HAZARDOUS MATERIALS (2020)

Add to Collection

Review Green & Sustainable Science & Technology

Lignocellulosic feedstock: A review of a sustainable platform for cleaner production of nature's plastics

Tanvi Govil et al.

JOURNAL OF CLEANER PRODUCTION (2020)

Add to Collection

Article Environmental Sciences

Direct extraction and detection of malachite green from marine sediments by magnetic nano-sized imprinted polymer coupled with spectrophotometric analysis

Min Zhao et al.

MARINE POLLUTION BULLETIN (2020)

Add to Collection

Article Agricultural Engineering

Pyrolysis and torrefaction of waste wood chips and cone-like flowers derived from black alder (Alnus glutinosa L. Gaertn.) for sustainable solid fuel production

Jakub Mokrzycki et al.

BIOMASS & BIOENERGY (2020)

Add to Collection

Article Engineering, Environmental

Mesoporous and high-surface-area activated carbon from defatted olive cake by-products of olive mills for the adsorption kinetics and isotherm of methylene blue and acid blue 29

F. Marrakchi et al.

JOURNAL OF ENVIRONMENTAL CHEMICAL ENGINEERING (2020)

Add to Collection

Article Agricultural Engineering

Characteristics of tetracycline adsorption by cow manure biochar prepared at different pyrolysis temperatures

Peizhen Zhang et al.

BIORESOURCE TECHNOLOGY (2019)

Add to Collection

Article Chemistry, Inorganic & Nuclear

RSM-CCD design of malachite green adsorption onto activated carbon with multimodal pore size distribution prepared from Amygdalus scoparia: Kinetic and isotherm studies

Rahele Bagheri et al.

POLYHEDRON (2019)

Add to Collection

Article Chemistry, Multidisciplinary

Synthesis and characterizations of activated carbon from Wisteria sinensis seeds biomass for energy storage applications

Ganesh Prasad Awasthi et al.

JOURNAL OF INDUSTRIAL AND ENGINEERING CHEMISTRY (2019)

Add to Collection

Proceedings Paper Engineering, Multidisciplinary

Influence of Alginate Encapsulation on Point of Zero Charge (pHpzc) and Thermodynamic Properties of the Natural and Fe(III) Modified Zeolite

Milan Kragovic et al.

12TH INTERNATIONAL CONFERENCE INTERDISCIPLINARITY IN ENGINEERING (INTER-ENG 2018) (2019)

Add to Collection

Article Chemistry, Multidisciplinary

Porous carbon material derived from fungal hyphae and its application for the removal of dye

Siji Chen et al.

RSC ADVANCES (2019)

Add to Collection

Article Geochemistry & Geophysics

Hydrothermal Synthesized and Alkaline Activated Carbons Prepared from Glucose and Fructose-Detailed Characterization and Testing in Heavy Metals and Methylene Blue Removal

Sanja Krstic et al.

MINERALS (2018)

Add to Collection

Article Chemistry, Physical

2D-NLDFT adsorption models for porous oxides with corrugated cylindrical pores

Jacek Jagiello et al.

JOURNAL OF COLLOID AND INTERFACE SCIENCE (2018)

Add to Collection

Review Biochemistry & Molecular Biology

Lignocellulose: A sustainable material to produce value-added products with a zero waste approach-A review

Alejandra Arevalo-Gallegos et al.

INTERNATIONAL JOURNAL OF BIOLOGICAL MACROMOLECULES (2017)

Add to Collection

Article Environmental Sciences

Influence of extracellular polymeric substances (EPS) treated by combined ultrasound pretreatment and chemical re-flocculation on water treatment sludge settling performance

Wei Chen et al.

CHEMOSPHERE (2017)

Add to Collection

Article Biochemistry & Molecular Biology

Isolation and Identification of Fourteen Microsatellite Markers in Clivia miniata and Clivia nobilis (Amaryllidaceae)

Wei Gao et al.

INTERNATIONAL JOURNAL OF MOLECULAR SCIENCES (2012)

Add to Collection

Article Biochemistry & Molecular Biology

Crystalline structure analysis of cellulose treated with sodium hydroxide and carbon dioxide by means of X-ray diffraction and FTIR spectroscopy

SY Oh et al.

CARBOHYDRATE RESEARCH (2005)

Add to Collection

© Peeref 2019-2024. All rights reserved.