4.6 Article

Critical Redistribution of Nitrogen in the Austenitic Cr-Mn Steel under Severe Plastic Deformation

Related references

Note: Only part of the references are listed.
Article Materials Science, Multidisciplinary

Structure-Phase Transformations in the Course of Solid-State Mechanical Alloying of High-Nitrogen Chromium-Manganese Steels

Kirill Lyashkov et al.

Summary: The solid-state mechanical alloying of high-nitrogen chromium-manganese austenite steel was studied using Mossbauer spectroscopy and TEM. It was found that using Mn2N as a nitrogen-containing addition is more preferable for the formation and stabilization of austenite.

METALS (2021)

Article Materials Science, Composites

Insight into ultra-refined grains of aluminum matrix composites via deformation-driven metallurgy

Yuming Xie et al.

Summary: Ultra-refined grains were achieved in aluminum matrix composites reinforced with few-layer graphene nanoplatelets through deformation-driven metallurgy under thermo-mechanical coupling, resulting in a significantly refined microstructure and high strengthening-toughening efficiency.

COMPOSITES COMMUNICATIONS (2021)

Article Materials Science, Multidisciplinary

Annealing behavior in a high-pressure torsion-processed Fe-9Cr steel

Jiaqi Duan et al.

JOURNAL OF MATERIALS SCIENCE (2020)

Article Metallurgy & Metallurgical Engineering

Deformation Behavior and Structural Evolution of Stainless Cr-Mn-N Steel during Low-Temperature Tension

N. A. Narkevich et al.

PHYSICS OF METALS AND METALLOGRAPHY (2020)

Article Metallurgy & Metallurgical Engineering

Short-Range Atomic Ordering Accelerated by Severe Plastic Deformation in FCC Invar Fe-Ni Alloys

V. A. Shabashov et al.

PHYSICS OF METALS AND METALLOGRAPHY (2019)

Article Metallurgy & Metallurgical Engineering

Deformation-Induced Dissolution and Precipitation of Nitrides in Austenite and Ferrite of a High-Nitrogen Stainless Steel

V. A. Shabashov et al.

PHYSICS OF METALS AND METALLOGRAPHY (2018)

Review Materials Science, Multidisciplinary

Atomic Order and Submicrostructure in Iron Alloys at Megaplastic Deformation

Valery Shabashov et al.

METALS (2018)

Article Metallurgy & Metallurgical Engineering

Scenarios of Nonequilibrium Phase Transformations in Alloys Depending on the Temperature and Intensity of Plastic Deformation

I. K. Razumov et al.

PHYSICS OF METALS AND METALLOGRAPHY (2018)

Article Materials Science, Multidisciplinary

Deformation-induced dissolution of the intermetallics Ni3 Ti and Ni3 Al in austenitic steels at cryogenic temperatures

V. V. Sagaradze et al.

PHILOSOPHICAL MAGAZINE (2016)

Article Metallurgy & Metallurgical Engineering

Dynamic aging in an Fe-Ni-Al alloy upon megaplastic deformation. Effect of the temperature and deformation rate

V. A. Shabashov et al.

PHYSICS OF METALS AND METALLOGRAPHY (2016)

Article Materials Science, Multidisciplinary

Evolution of defects in copper deformed by high-pressure torsion

J. Cizek et al.

ACTA MATERIALIA (2011)

Article Metallurgy & Metallurgical Engineering

Anomalous Diffusion Phase Transformations in Steels upon Severe Cold Deformation

V. V. Sagaradze et al.

PHYSICS OF METALS AND METALLOGRAPHY (2011)

Article Nanoscience & Nanotechnology

Reduction of vacancy concentration during storage of severely deformed Cu

J. Gubicza et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2010)

Article Physics, Condensed Matter

Physics of megaplastic (Severe) deformation in solids

A. M. Glezer et al.

PHYSICS OF THE SOLID STATE (2010)

Article Materials Science, Multidisciplinary

Influence of the relaxation processes on the structure formation in pure metals and alloys under high-pressure torsion

M. V. Degtyarev et al.

ACTA MATERIALIA (2007)

Article Physics, Atomic, Molecular & Chemical

Mossbauer spectroscopy of locally inhomogeneous systems

V. S. Rusakov et al.

HYPERFINE INTERACTIONS (2005)

Article Nanoscience & Nanotechnology

Microstructural evolution and hardening parameters

N Hansen et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2001)