Related references
Note: Only part of the references are listed.Numerical Simulation of Laser Welding Dissimilar Low Carbon and Austenitic Steel Joint
Hubert Danielewski et al.
OPEN ENGINEERING (2020)
Solid-state phase transformation and strain hardening on the residual stresses in S355 steel weldments
Jiamin Sun et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2019)
Numerical Analysis of Longitudinal Residual Stresses and Deflections in a T-joint Welded Structure Using a Local Preheating Technique
Mato Peric et al.
ENERGIES (2018)
Numerical investigation of formation mechanism of welding residual stress in P92 steel multi-pass joints
Suo Li et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2017)
Numerical studies of welding residual stresses in tubular joints and experimental validations by means of x-ray and neutron diffraction analysis
Kimiya Hemmesi et al.
MATERIALS & DESIGN (2017)
Influence of the welding sequence on residual stress and distortion of fillet welded structures
Guangming Fu et al.
MARINE STRUCTURES (2016)
Study on the microstructure, mechanical properties and corrosion behaviour of S355JR/316L dissimilar welded joint prepared by gas tungsten arc welding multi-pass welding process
B. -S. Huang et al.
SCIENCE AND TECHNOLOGY OF WELDING AND JOINING (2016)
Modelling the creation and destruction of columnar and equiaxed zones during solidification and melting in multi-pass welding of steel
G. Duggan et al.
COMPUTATIONAL MATERIALS SCIENCE (2015)
Simulation of laser butt welding of AISI 316L stainless steel sheet using various heat sources and experimental validation
Jazeel Rahman Chukkan et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2015)
Microstructure and properties of Mg/Al joint welded by gas tungsten arc welding-assisted hybrid ultrasonic seam welding
Xiangyu Dai et al.
MATERIALS & DESIGN (2015)
Numerical simulation on the effect of welding parameters on welding residual stresses in T92/S30432 dissimilar welded pipe
Lei Zhao et al.
ADVANCES IN ENGINEERING SOFTWARE (2014)
Effect of boundary conditions on residual stress and distortion in T-joint welds
Guangming Fu et al.
JOURNAL OF CONSTRUCTIONAL STEEL RESEARCH (2014)
Short-Term High-Temperature Tensile Tests and Prediction of Long-Term Strength of Welded Joints of Dissimilar Steels T92/HR3C
Y. M. Song et al.
METAL SCIENCE AND HEAT TREATMENT (2014)
Characterization of material properties and heat source parameters in welding simulation of two overlapping beads on a substrate plate
Suraj Joshi et al.
COMPUTATIONAL MATERIALS SCIENCE (2013)
Influence of deposition sequence on welding residual stress and deformation in an austenitic stainless steel J-groove welded joint
Dean Deng
MATERIALS & DESIGN (2013)
Temperature and residual stress simulations of the NeT single-bead-on-plate specimen using SYSWELD
J. J. Xu et al.
INTERNATIONAL JOURNAL OF PRESSURE VESSELS AND PIPING (2012)
Methods of measuring residual stresses in components
N. S. Rossini et al.
MATERIALS & DESIGN (2012)
Effect of heat source configuration on the result quality of numerical calculation of welding-induced distortion
C. Heinze et al.
SIMULATION MODELLING PRACTICE AND THEORY (2012)
Determination of welding stress and distortion in discontinuous welding by means of numerical simulation and comparison with experimental measurements
Zhi Zeng et al.
COMPUTATIONAL MATERIALS SCIENCE (2010)
FEM prediction of welding residual stresses in a SUS304 girth-welded pipe with emphasis on stress distribution near weld start/end location
Dean Deng et al.
COMPUTATIONAL MATERIALS SCIENCE (2010)
Adaptive mesh technique for thermal-metallurgical numerical simulation of arc welding processes
M. Hamide et al.
INTERNATIONAL JOURNAL FOR NUMERICAL METHODS IN ENGINEERING (2008)
Effects of temperature-dependent material properties on welding simulation
XK Zhu et al.
COMPUTERS & STRUCTURES (2002)