Related references
Note: Only part of the references are listed.Effect of quench-tempering conditions prior to nitriding on microstructure and fretting wear mechanism of gas nitrided X210CrW12 steel
Yong Duan et al.
SURFACE & COATINGS TECHNOLOGY (2019)
The effect of grinding parameters and gas nitriding depth on the grindability and surface integrity of AISI D2 tool steel
Brahim Ben Fathallah et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2019)
Gaseous nitriding behaviour of 33CrMoV12-9 steel: Evolution of the grain boundaries precipitation and influence on residual stress development
Sebastien Jegou et al.
SURFACE & COATINGS TECHNOLOGY (2018)
Effects of chromium additions on the three-body abrasive wear behavior of Fe-3.0 wt% B alloy
Yongxin Jian et al.
WEAR (2017)
A comparative study of salt-bath nitrocarburizing and gas nitriding followed by post-oxidation used as surface treatments of H13 hot forging dies
Marcos Perez et al.
SURFACE & COATINGS TECHNOLOGY (2016)
Alternative phase transformation path in cryogenically treated AISI D2 tool steel
Hadi Ghasemi Nanesa et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2015)
Wear behavior of AISI D2 steel by enhanced ion nitriding with atomic attrition
Kyun Taek Cho et al.
TRIBOLOGY INTERNATIONAL (2015)
Microstructure evolution and abrasive wear behavior of D2 steel
Kritika Singh et al.
WEAR (2015)
Effect of plasma nitriding potential on tribological behaviour of AISI D2 cold-worked tool steel
Maycoln Depianti Conci et al.
WEAR (2014)
Study of abrasive wear phenomena in dry and slurry 3-body conditions
M. Petrica et al.
TRIBOLOGY INTERNATIONAL (2013)
Dry sliding friction and wear behaviour of hardened AISI D2 tool steel with different hardness levels
Linhu Tang et al.
TRIBOLOGY INTERNATIONAL (2013)
Influence of counterbody material on fretting wear behaviour of surface mechanical attrition treated Ti-6Al-4V
S. Anand Kumar et al.
TRIBOLOGY INTERNATIONAL (2013)
The effect of contact geometry on fretting wear rates and mechanisms for a high strength steel
A. R. Warmuth et al.
WEAR (2013)
Fretting wear behaviour of 304 stainless steel fretted against different counterbody materials
S. A. Kumar et al.
TRIBOLOGY-MATERIALS SURFACES & INTERFACES (2013)
Preparation, microstructure and properties of molybdenum alloys reinforced by in-situ Al2O3 particles
Liujie Xu et al.
INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS (2012)
Phase transformations and induced volume changes in a nitrided ternary Fe-3%Cr-0.345%C alloy
S. Jegou et al.
ACTA MATERIALIA (2010)
Particle size effect on abrasion resistance of mottled cast iron with different retained austenite contents
J. J. Coronado et al.
WEAR (2009)
Fretting wear behaviour of plasma nitrided Ti-6Al-4V fretted against unnitrided Ti-6Al-4V and alumina counterbodies
M. Mubarak Ali et al.
TRANSACTIONS OF THE INDIAN INSTITUTE OF METALS (2009)
Effect of hardness on fretting wear behaviour of structural steel, En 24, against bearing steel, En 31
R. Ramesh et al.
MATERIALS & DESIGN (2007)
Optimization of testing parameters on the wear behaviour of metal matrix composites based on the Taguchi method
Y Sahin
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2005)
Different aspects of the role of wear debris in fretting wear
M Varenberg et al.
WEAR (2002)
Microstructural changes and contact temperatures during fretting in steel-steel contact
B Podgornik et al.
JOURNAL OF TRIBOLOGY-TRANSACTIONS OF THE ASME (2001)
Share Paper
