Related references
Note: Only part of the references are listed.Investigation of the Air-Argon-Steel-Slag Flow in an Industrial RH Reactor with VOF-DPM Coupled Model
Gujun Chen et al.
METALLURGICAL AND MATERIALS TRANSACTIONS B-PROCESS METALLURGY AND MATERIALS PROCESSING SCIENCE (2017)
CFD simulation of local and global mixing time in an agitated tank
Li Liangchao et al.
CHINESE JOURNAL OF MECHANICAL ENGINEERING (2017)
The Effects of Bottom Blowing Gas Flow Rate Distribution During the Steelmaking Converter Process on Mixing Efficiency
Kuan-Yu Chu et al.
METALLURGICAL AND MATERIALS TRANSACTIONS B-PROCESS METALLURGY AND MATERIALS PROCESSING SCIENCE (2016)
Multiphase Modeling of Bottom-Stirred Ladle for Prediction of Slag-Steel Interface and Estimation of Desulfurization Behavior
Umesh Singh et al.
METALLURGICAL AND MATERIALS TRANSACTIONS B-PROCESS METALLURGY AND MATERIALS PROCESSING SCIENCE (2016)
Toward CFD Modeling of Slag Entrainment in Gas Stirred Ladles
Ao Huang et al.
STEEL RESEARCH INTERNATIONAL (2015)
Fluid dynamic analysis of a continuous stirred tank reactor for technical optimization of wastewater digestion
F. J. Hurtado et al.
WATER RESEARCH (2015)
Mathematical and Physical Simulation of a Top Blown Converter
Xiaobin Zhou et al.
STEEL RESEARCH INTERNATIONAL (2014)
Modelling of mixing, mass transfer and phase distribution in a Peirce-Smith converter model
D. K. Chibwe et al.
CANADIAN METALLURGICAL QUARTERLY (2013)
Numerical simulation of gas and liquid flow in steelmaking converter with top and bottom combined blowing
Y. Li et al.
IRONMAKING & STEELMAKING (2013)
Research on Top and Bottom Mixed Blowing CO2 in Converter Steelmaking Process
Ming Lv et al.
STEEL RESEARCH INTERNATIONAL (2012)
Mathematical and physical simulation of the interaction between a gas jet and a liquid free surface
J. Solorzano-Lopez et al.
APPLIED MATHEMATICAL MODELLING (2011)
Mathematical Modeling Study on Combined Side and Top Blowing AOD Refining Process of Stainless Steel
Ji-He Wei et al.
ISIJ INTERNATIONAL (2011)
Numerical Simulation of Fluid Flow and Interfacial Behavior in Three-phase Argon-Stirred Ladles with One Plug and Dual Plugs
Heping Liu et al.
STEEL RESEARCH INTERNATIONAL (2011)
Multiphase Modeling of the Fluidynamics of Bottom Argon Bubbling during Ladle Operations
Carlos A. Llanos et al.
ISIJ INTERNATIONAL (2010)
Liquid Mixing in Thick-Slag-Covered Metallurgical Baths-Blending of Bath
Leili Tafaghodi Khajavi et al.
METALLURGICAL AND MATERIALS TRANSACTIONS B-PROCESS METALLURGY AND MATERIALS PROCESSING SCIENCE (2010)
Towards Efficient Modelling of Slag Entrainment during Metallurgical Processes
S. Pirker
STEEL RESEARCH INTERNATIONAL (2010)
CFD Model for Emulsification of Slag into the Steel
Petri Sulasalmi et al.
ISIJ INTERNATIONAL (2009)
A mathematical modelling study of fluid flow and mixing in full-scale gas-stirred ladles
Schalk W. P. Cloete et al.
PROGRESS IN COMPUTATIONAL FLUID DYNAMICS (2009)
Influence of bottom tuyere configuration on bath stirring in a top and bottom combined blown converter
Zhaoyi Lai et al.
ISIJ INTERNATIONAL (2008)
Study of stag/metal interface in ladle treatment
P. Dayal et al.
IRONMAKING & STEELMAKING (2006)
Determination of mixing time and degree of homogeneity in stirred vessels with large eddy simulation
SL Yeoh et al.
CHEMICAL ENGINEERING SCIENCE (2005)
Vibration of argon-oxygen decarburisation vessel during gas injection
TMJ Fabritius et al.
IRONMAKING & STEELMAKING (2005)
Slag emulsification during liquid steel desulphurisation by gas injection into the ladle
H Lachmund et al.
STEEL RESEARCH INTERNATIONAL (2003)
Generation of droplets in slag-metal emulsions through top gas blowing
Subagyo et al.
ISIJ INTERNATIONAL (2003)
Modeling of gas-liquid reactions in ladle metallurgy: Part II. Numerical simulation
D Guo et al.
METALLURGICAL AND MATERIALS TRANSACTIONS B-PROCESS METALLURGY AND MATERIALS PROCESSING SCIENCE (2000)
Share Paper
