Related references
Note: Only part of the references are listed.Elevated-temperature super-lubrication performance analysis of dispersion-strengthened WSN coatings: Experimental research and first-principles calculation
Jianing Zhu et al.
SURFACE & COATINGS TECHNOLOGY (2021)
Effect of shot peening residual stresses and surface roughness on fretting fatigue strength of Al 7075-T651
Vicente Martin et al.
TRIBOLOGY INTERNATIONAL (2020)
Evolution of surface integrity and fatigue properties after milling, polishing, and shot peening of TC17 alloy blades
Liang Tan et al.
INTERNATIONAL JOURNAL OF FATIGUE (2020)
Characterization of residual stresses and microstructural features in an Inconel 718 forged compressor disc
Xiao-yan Xu et al.
TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2019)
The application of TiSiN/TiAlN coatings in the mitigation of fretting wear in push fit joints
Slawomir Kowalski et al.
WEAR (2019)
Fretting fatigue behaviors and surface integrity of Ag-TiN soft solid lubricating films on titanium alloy
Dongxing Du et al.
APPLIED SURFACE SCIENCE (2019)
Effect of shot peening on fatigue performance of Ti2AlNb intermetallic alloy
Y. X. Chen et al.
INTERNATIONAL JOURNAL OF FATIGUE (2019)
The effect of residual stress and gradient nanostructure on the fretting fatigue behavior of plasma electrolytic oxidation coated Ti-6Al-4V alloy
Ni Ao et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2019)
Fretting wear and fatigue in press-fitted railway axle: A simulation study of the influence of stress relief groove
Dongfang Zeng et al.
INTERNATIONAL JOURNAL OF FATIGUE (2019)
Investigation of shot peening combined with plasma-sprayed CuNiIn coating on the fretting fatigue behavior of Ti-6Al-4V dovetail joint specimens
Qi Yang et al.
SURFACE & COATINGS TECHNOLOGY (2019)
Fretting wear properties of HVOF-sprayed CoMoCrSi coatings with different spraying parameters
Wen-jin Yang et al.
SURFACE & COATINGS TECHNOLOGY (2019)
WS2 Nanopowders as High-Temperature Lubricants: An Experimental and Theoretical Study
Jianing Zhu et al.
ACS APPLIED NANO MATERIALS (2019)
Surface characteristics and fatigue behavior of shot peened Inconel 718
T. Klotz et al.
INTERNATIONAL JOURNAL OF FATIGUE (2018)
Surface characterization and fatigue evaluation in GH4169 superalloy : Comparing results after finish turning; shot peening and surface polishing treatments
Daoxia Wu et al.
INTERNATIONAL JOURNAL OF FATIGUE (2018)
Effect of different surface asperities and surface hardness induced by shot-peening on the fretting wear behavior of Ti-6Al-4V
Qi Yang et al.
SURFACE & COATINGS TECHNOLOGY (2018)
Investigation on the fretting fatigue behaviors of Ti-6A1-4V dovetail joint specimens treated with shot-peening
Qi Yang et al.
WEAR (2017)
Role of WS2, WS2 + CrC and bonded coatings on damage and friction of Inconel 718 flat rough surfaces at high temperature
J. Fortes Da Cruz et al.
TRIBOLOGY INTERNATIONAL (2016)
Properties of W/DLC/W-S-C composite films fabricated by magnetron sputtering
Ming-jiang Dai et al.
TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2015)
Nanostructured WS2-Ni composite films for improved oxidation, resistance and tribological performance
Shusheng Xu et al.
APPLIED SURFACE SCIENCE (2014)
The influence of DLC coating on the mechanical and frictional properties of unpeened and peened Cu-based bimetal under dry sliding conditions
Auezhan Amanov et al.
MATERIALS CHEMISTRY AND PHYSICS (2014)
A fuzzy logic predictive model for better surface roughness of Ti-TiN coating on AL7075-T6 alloy for longer fretting fatigue life
E. Zalnezhad et al.
MEASUREMENT (2014)
Morphology evolution of Ag alloyed WS2 films and the significantly enhanced mechanical and tribological properties
Shusheng Xu et al.
SURFACE & COATINGS TECHNOLOGY (2014)
Experimental investigation and fatigue life prediction for 7475-T7351 aluminum alloy with and without shot peening-induced residual stresses
Y. K. Gao et al.
ACTA MATERIALIA (2011)
Improvement of fatigue property in 7050-T7451 aluminum alloy by laser peening and shot peening
Y. K. Gao
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2011)
Mechanical and tribological properties of sputter deposited nanostructured Cr-WS2 solid lubricant coatings
B. Deepthi et al.
SURFACE & COATINGS TECHNOLOGY (2010)
Structure, morphology and chemical composition of sputter deposited nanostructured Cr-WS2 solid lubricant coatings
B. Deepthi et al.
SURFACE & COATINGS TECHNOLOGY (2010)
Development of a dovetail fretting fatigue fixture for turbine engine materials
Patrick J. Golden
INTERNATIONAL JOURNAL OF FATIGUE (2009)
The effects of deep rolling and shot peening on fretting fatigue resistance of Aluminum-7075-T6
G. H. Majzoobi et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2009)
Influence of surface coating on Ti811 alloy resistance to fretting fatigue at elevated temperature
Zhang Xiaohua et al.
RARE METALS (2009)
Growth, structure and friction behavior of titanium doped tungsten disulphide (Ti-WS2) nanocomposite thin films
T. W. Scharf et al.
THIN SOLID FILMS (2009)
The effects of laser peening and shot peening on fretting fatigue in Ti-6Al-4V coupons
Kevin K. Liu et al.
TRIBOLOGY INTERNATIONAL (2009)
Performance of plasma sprayed and detonation gun sprayed Cu-Ni-In coatings on Ti-6Al-4V under plain fatigue and fretting fatigue loading
B. Rajasekaran et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2008)
The effect of pre-treatment of substrate on fretting tribological behavior of MoS2 coatings
GZH Xu et al.
WEAR (2003)
An analysis of residual stress fields caused by shot peening
YK Gao et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2002)
Mechanical properties of arc-evaporated CrN coatings. Part II: intrinsic film hardness and composite hardness
H Ichimura et al.
SURFACE & COATINGS TECHNOLOGY (2001)
Share Paper
