☆ 4.5 Article

Evolution of temperature and residual stress behavior in selective laser melting of 316L stainless steel across a cooling channel

RAPID PROTOTYPING JOURNAL (2022)

Related references

Note: Only part of the references are listed.

Article Optics

Evolution of residual stress behavior in selective laser melting (SLM) of 316L stainless steel through preheating and in-situ re-scanning techniques

Saad Waqar et al.

Summary: The premature fractures, cracks, distortions, and delamination in selective laser melting manufactured components are among the most prominent challenges. Residual stresses are the main causes of these issues. Post processing techniques are commonly used to reduce these stresses, but they increase production time and costs. Therefore, developing in-process techniques to reduce residual stresses is crucial for large-scale production of metallic components.

OPTICS AND LASER TECHNOLOGY (2022)

Add to Collection

Article Engineering, Manufacturing

Thermo-mechanical modelling of stress relief heat treatments after laser-based powder bed fusion

David De Baere et al.

Summary: This study investigates the effect of stress relief heat treatment in laser-based powder bed fusion post-processing, modeling the impact of post-processing parameters on residual stress. The results show that heat treatment can alleviate residual stress in parts, allowing for the selection of optimal heat treatment conditions based on simulation results and reducing the need for extensive experimentation.

ADDITIVE MANUFACTURING (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Numerical and experimental investigations of built orientation dependent Johnson-Cook model for selective laser melting manufactured AlSi10Mg

Murat Akturk et al.

Summary: This study focuses on the material constitutive parameters of the widely used aluminum alloy AlSi10Mg, using SLM technology to manufacture tensile samples and conducting quasi-static and high temperature tensile tests to determine the Johnson-Cook material model. The comparison between numerically simulated tensile results and experimental results shows a maximum error of around 7.5%, demonstrating the accuracy of the established material model.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2021)

Add to Collection

Review Engineering, Manufacturing

Selective laser melting of Ti6Al4V alloy: Process parameters, defects and post-treatments

Anil Kumar Singla et al.

Summary: This review critically examines the important contributions related to selective laser melting (SLM) process parameters, defects, and post-processing techniques for Ti6Al4V alloy. Proper selection of process parameters and post-treatment methods are crucial in improving mechanical behavior of SLMed components. Efforts have been made to identify correlations between SLM parameters and defects, as well as analyzing the impact of post-processing approaches on mechanical behavior and biocompatibility of SLM-fabricated Ti6Al4V alloy.

JOURNAL OF MANUFACTURING PROCESSES (2021)

Add to Collection

Article Engineering, Manufacturing

FEM analysis of thermal and residual stress profile in selective laser melting of 316L stainless steel

Saad Waqar et al.

Summary: High temperature gradients and residual stresses are major challenges in selective laser melting. Understanding the influence of process parameters on thermal and residual stress profiles is crucial. A study using a 3D FEM model found that increasing laser power or decreasing scanning speed raises maximum melt pool temperature and increasing laser power or speed raises cooling rates and residual stresses. Increasing hatch spacing leads to increased max melt pool temp and decreased residual stress.

JOURNAL OF MANUFACTURING PROCESSES (2021)

Add to Collection

Article Engineering, Mechanical

A numerical prediction of residual stress for a thin-walled part with geometrical features fabricated by GMA-based additive manufacturing

Rong Li et al.

RAPID PROTOTYPING JOURNAL (2020)

Add to Collection

Article Optics

Effect of the track length and track number on the evolution of the molten pool characteristics of SLMed Al alloy: Numerical and experimental study

Shiwen Liu et al.

OPTICS AND LASER TECHNOLOGY (2020)

Add to Collection

Article Engineering, Mechanical

Effect of post-heat treatment cooling on microstructure and mechanical properties of selective laser melting manufactured austenitic 316L stainless steel

Saad Waqar et al.

RAPID PROTOTYPING JOURNAL (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Impact of layer rotation on micro-structure, grain size, surface integrity and mechanical behaviour of SLM Al-Si-10Mg alloy

Munish Kumar Gupta et al.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2020)

Add to Collection

Article Optics

Influence of laser power and scanning strategy on residual stress distribution in additively manufactured 316L steel

Peiying Bian et al.

OPTICS AND LASER TECHNOLOGY (2020)

Add to Collection

Review Engineering, Manufacturing

Influence of the post-processing operations on surface integrity of metal components produced by laser powder bed fusion additive manufacturing: a review

Hamaid Mahmood Khan et al.

MACHINING SCIENCE AND TECHNOLOGY (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Investigations on density and surface roughness characteristics during selective laser sintering of Invar-36 alloy

Navneet Khanna et al.

MATERIALS RESEARCH EXPRESS (2019)

Add to Collection

Article Engineering, Mechanical

The effect of process parameters on the residual stress of selective laser melted Inconel 718 thin-walled part

Changpeng Chen et al.

RAPID PROTOTYPING JOURNAL (2019)

Add to Collection

Article Engineering, Manufacturing

Effect of overlap rate and pattern on residual stress in selective laser melting

Changpeng Chen et al.

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2019)

Add to Collection

Article Optics

Finite element analysis of melt pool thermal characteristics with passing laser in SLM process

M. Majeed et al.

OPTIK (2019)

Add to Collection

Review Engineering, Biomedical

Mechanical performance of additively manufactured meta-biomaterials

Amir A. Zadpoor

ACTA BIOMATERIALIA (2019)

Add to Collection

Review Materials Science, Multidisciplinary

Additive manufacturing of metallic components - Process, structure and properties

T. DebRoy et al.

PROGRESS IN MATERIALS SCIENCE (2018)

Add to Collection

Article Engineering, Mechanical

Analytical modelling of residual stress in additive manufacturing

O. Fergani et al.

FATIGUE & FRACTURE OF ENGINEERING MATERIALS & STRUCTURES (2017)

Add to Collection

Review Engineering, Multidisciplinary

Overhanging Features and the SLM/DMLS Residual Stresses Problem: Review and Future Research Need

Albert E. Patterson et al.

TECHNOLOGIES (2017)

Add to Collection

Article Engineering, Mechanical

Effect of preheat and layer thickness on selective laser melting (SLM) of magnesium

Monica Mahesh Savalani et al.

RAPID PROTOTYPING JOURNAL (2016)

Add to Collection

Article Engineering, Mechanical

Residual stresses in selective laser sintering and selective laser melting

Peter Mercelis et al.

RAPID PROTOTYPING JOURNAL (2006)

Add to Collection

© Peeref 2019-2024. All rights reserved.