Related references
Note: Only part of the references are listed.Comparison of crystallization characteristics and mechanical properties of polypropylene processed by ultrasound and conventional micro-injection molding
Davide Masato et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2018)
The effect of injection molding process parameters on mechanical and fracture behavior of polycarbonate polymer
Uzair Ahmed Dar et al.
JOURNAL OF APPLIED POLYMER SCIENCE (2017)
Analysis of the shrinkage of injection-molded fiber-reinforced thin-wall parts
Davide Masato et al.
MATERIALS & DESIGN (2017)
Experimental investigation and modeling of mechanical behaviors of polyurea over wide ranges of strain rates and temperatures
Hui Guo et al.
POLYMER TESTING (2016)
Processing-Induced Inhomogeneity of Yield Stress in Polycarbonate Product and Its Influence on the Impact Behavior
Yingjie Xu et al.
POLYMERS (2016)
Predicting the low-velocity impact behavior of polycarbonate: Influence of thermal history during injection molding
Yingjie Xu et al.
INTERNATIONAL JOURNAL OF IMPACT ENGINEERING (2015)
Effects of equal-channel, multiple-angular extrusion on the physical and mechanical properties of glassy polymers
Victor A. Beloshenko et al.
JOURNAL OF APPLIED POLYMER SCIENCE (2015)
Low speed impact of laminated polymethylmethacrylate/adhesive/polycarbonate plates
G. O. Antoine et al.
COMPOSITE STRUCTURES (2014)
Residual stresses in injection molded products
A. Guevara-Morales et al.
JOURNAL OF MATERIALS SCIENCE (2014)
Rate- and temperature-dependent strain hardening of polycarbonate
D. J. A. Senden et al.
JOURNAL OF POLYMER SCIENCE PART B-POLYMER PHYSICS (2012)
Effects of strain rate and temperature on the tension behavior of polycarbonate
Kan Cao et al.
MATERIALS & DESIGN (2012)
Uniaxial compression and combined compression-and-shear response of amorphous polycarbonate at high loading rates
Vikas Prakash et al.
POLYMER ENGINEERING AND SCIENCE (2012)
Tensile behavior of polycarbonate over a wide range of strain rates
Kan Cao et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2010)
Predicting the Long-Term Mechanical Performance of Polycarbonate from Thermal History during Injection Molding
Tom A. P. Engels et al.
MACROMOLECULAR MATERIALS AND ENGINEERING (2009)
Processing-induced properties in glassy polymers: Application of structural relaxation to yield stress development
TAP Engels et al.
JOURNAL OF POLYMER SCIENCE PART B-POLYMER PHYSICS (2006)
The high strain rate compressive behaviour of polycarbonate and polyvinylidene difluoride
CR Siviour et al.
POLYMER (2005)
Modeling of morphology evolution in the injection molding process of thermoplastic polymers
R Pantani et al.
PROGRESS IN POLYMER SCIENCE (2005)
Modeling of the postyield response of glassy polymers: Influence of thermomechanical history
ETJ Klompen et al.
MACROMOLECULES (2005)
Processing-induced properties in glassy polymers - Development of the yield stress in PC
LE Govaert et al.
INTERNATIONAL POLYMER PROCESSING (2005)
Investigations of the tensile properties on polycarbonate thin-wall injection molded parts
SC Chen et al.
JOURNAL OF REINFORCED PLASTICS AND COMPOSITES (2003)
A split Hopkinson pressure bar technique to determine compressive stress-strain data for rock materials
DJ Frew et al.
EXPERIMENTAL MECHANICS (2001)
Strain-hardening behavior of polycarbonate in the glassy state
TA Tervoort et al.
JOURNAL OF RHEOLOGY (2000)
The influence of intrinsic strain softening on strain localization in polycarbonate: Modeling and experimental validation
LE Govaert et al.
JOURNAL OF ENGINEERING MATERIALS AND TECHNOLOGY-TRANSACTIONS OF THE ASME (2000)
Share Paper
