☆ 4.7 Article

The effect of halloysite nanotube modification on wear behavior of carbon-aramid fiber reinforced hybrid nanocomposites

POLYMER COMPOSITES (2022)

Related references

Note: Only part of the references are listed.

Article Chemistry, Physical

Halloysite nanotubes filled with MgO for paper reinforcement and deacidification

Lorenzo Lisuzzo et al.

Summary: A novel material using MgO filled halloysite nanotubes has been developed for deacidification and protection of paper. The composite material effectively neutralizes the acidic degradation of paper, improves tensile strength, delays aging, and maintains the mechanical and visual properties of paper during the consolidation process.

APPLIED CLAY SCIENCE (2021)

Add to Collection

Article Mechanics

An experimental study on low velocity impact performance of bolted composite joints-part 2: Influence of long-term seawater aging

Halil Burak Kaybal et al.

Summary: This paper investigates the low-velocity impact response of bolted fiber-reinforced polymer joints in two scenarios, and evaluates the impact of halloysite nanotubes (HNTs) reinforcement of the epoxy matrix. The effects of seawater aging on the impact performance of the joints are also studied, with results showing a decrease in impact resistance after aging, but an improvement when using HNTs reinforced joints. The ToB impact scenario is considered more detrimental than the SoW tests, and a novel damage mechanism is introduced to address the impact of seawater aging.

COMPOSITE STRUCTURES (2021)

Add to Collection

Article Engineering, Chemical

Hydroxypropyl Cellulose Films Filled with Halloysite Nanotubes/Wax Hybrid Microspheres

Lorenzo Lisuzzo et al.

Summary: The design and preparation of novel HPC/wax/halloysite nanocomposites have led to films with good hydrophobic properties and surface protection capabilities. Based on measurements of contact angle, sliding angle, and vapor permeability of the composite materials, these composites show potential gas barrier effects.

INDUSTRIAL & ENGINEERING CHEMISTRY RESEARCH (2021)

Add to Collection

Article Materials Science, Composites

Mechanical, wear, and drop load impact behavior of glass/Caryota urens hybridized fiber-reinforced nanoclay/SiC toughened epoxy multihybrid composite

P. Raju et al.

Summary: This study aimed to improve the performance of epoxy resin composite materials by adding different amounts of silicon carbide and nanoclay. The addition of 1.0% silicon carbide resulted in enhanced tensile properties, reduced wear rate, increased penetration resistance, and energy absorption of the composite.

POLYMER COMPOSITES (2021)

Add to Collection

Article Engineering, Chemical

Percolation and Reynolds Flow in Elastic Contacts of Isotropic and Anisotropic, Randomly Rough Surfaces

Anle Wang et al.

Summary: In this work, the elastic contact between isotropic and anisotropic, rigid, randomly rough surfaces and linearly elastic counterfaces, as well as the subsequent Reynolds flow through the gap between them, is numerically studied. The percolation threshold is found to be dependent on fluid flow direction in anisotropic systems, and a critical contact area near 0.415 is confirmed. Effective-medium treatments provide accurate expressions for Reynolds fluid flow conductances.

TRIBOLOGY LETTERS (2021)

Add to Collection

Article Mechanics

An experimental study on low velocity impact performance of bolted composite joints part 1: Influence of halloysite nanotubes on dynamic loading response

Halil Burak Kaybal et al.

Summary: The goal of this study is to investigate the dynamic loading response of bolted basalt-epoxy composite laminates under different impact energies, and evaluate the effects of HNTs reinforcement on the impact response and damage propagation. The results show that ToB damage is relatively severe, HNTs can improve impact resistance by about 15%, especially at lower impact energies.

COMPOSITE STRUCTURES (2021)

Add to Collection

Article Engineering, Multidisciplinary

Significantly improved shear, dynamic-mechanical, and mode II fracture performance of seawater aged basalt/epoxy composites: The impact of halloysite nanotube reinforcement

Hasan Ulus et al.

Summary: Recent studies have shown that introducing halloysite nanotubes into the polymer matrix offers an efficient barrier effect and improved fiber-matrix interface in seawater environment, crucial for enhancing the mechanical performance of composites. Experimental results indicated that HNTs reinforced multi-scale composites exhibited higher shear strength and mode II delamination toughness after aging in sea-water, showing potential for future engineering applications.

ENGINEERING SCIENCE AND TECHNOLOGY-AN INTERNATIONAL JOURNAL-JESTECH (2021)

Add to Collection

Article Chemistry, Physical

Comparative cytotoxicity of kaolinite, halloysite, multiwalled carbon nanotubes and graphene oxide

Elvira Rozhina et al.

Summary: This study compared the interactions of carbon nanomaterials and nanoclays with human lung adenocarcinoma cells, finding that carbon nanomaterials were more toxic and genotoxic to cells. The shape of the nanomaterials did not significantly affect their internalization and cytotoxicity.

APPLIED CLAY SCIENCE (2021)

Add to Collection

Article Materials Science, Textiles

Seawater Aged Basalt/Epoxy Composites: Improved Bearing Performance with Halloysite Nanotube Reinforcement

Halil Burak Kaybal et al.

Summary: The research focused on the impact of seawater aging and halloysite nanotube (HNT) nano reinforcements on the bearing performance of basalt-epoxy composites. It was found that HNT nano reinforcements significantly improved the bearing strength by 18%, while seawater aging caused a nearly 45% reduction in bearing strength. The addition of HNTs and seawater aging also affected bearing fracture modes, with the resultant fracture surfaces revealing degradation mechanisms related to these factors. These results provide insights for designing bolted fiber reinforced polymer composites exposed to corrosive environments.

FIBERS AND POLYMERS (2021)

Add to Collection

Article Chemistry, Multidisciplinary

Preparation of poly(MPAEMA)/halloysite Nanocomposites and Investigation of Antiproliferative Activity

Nevin Cankaya et al.

Summary: The study investigated the synthesis, characterization, and thermal properties of MPAEMA polymer/clay-based nanocomposites through in-situ polymerization, showing a positive correlation between clay ratio and thermal stability. XTT assay revealed that the nanocomposites had a non-cytotoxic response on HeLa cells, suggesting their safe utility in various research areas.

JOURNAL OF THE MEXICAN CHEMICAL SOCIETY (2021)

Add to Collection

Article Materials Science, Composites

Preparation and characterization of poly(vinyl alcohol)/halloysite nanotubes composite sponges with improved mechanical properties

Tianxiang Chen et al.

Summary: The incorporation of HNTs was found to enhance the mechanical properties and controlled release ability of PVA composite sponges; composite sponges exhibited better thermal stability and water absorption capacity compared to pure PVA sponges.

POLYMER COMPOSITES (2021)

Add to Collection

Article Materials Science, Composites

Tribological and mechanical fracture performance of Mediterranean lignocellulosic fiber reinforced polypropylene composites

Faris M. AL-Oqla et al.

Summary: This study investigated the performance of Mediterranean lignocellulosic fiber-reinforced polypropylene composites using various Jordanian lignocellulosic fibers. Results showed significant effects of different fibers on the mechanical performance characteristics of the composites, particularly enhancing stiffness property. Additionally, coefficient of friction was found to vary with fiber loading and type.

POLYMER COMPOSITES (2021)

Add to Collection

Article Materials Science, Composites

Effect of repeated hydrothermal cycling on the durability of glass fiber/epoxy composites with and without carbon nanotube reinforcement

Abhinav Omprakash Fulmali et al.

Summary: This study explores the enhancement of polymeric composites by incorporating carbon nanotubes (CNT) and investigates the performance of glass fiber reinforced epoxy (GE) composite with and without CNT under repeated hydrothermal cycling. The research confirms that the addition of 0.1 wt% of CNTs resulted in increased flexural strength and modulus compared to neat GE composite. Furthermore, the study reveals that the mechanical performance of the CNT embedded GE composite degrades faster than the neat one with the increasing number of hydrothermal cycles, with explanations provided based on analysis from various techniques.

POLYMER COMPOSITES (2021)

Add to Collection

Review Materials Science, Composites

Effect of hybridization on properties of natural and synthetic fiber-reinforced polymer composites (2001-2020): A review

M. K. Gupta et al.

Summary: In the past two decades, researchers have been studying hybrid composite materials reinforced with synthetic and natural fibers to overcome the limitations of natural fibers such as moisture absorption and compatibility. Various studies have been conducted on the properties of hybrid composites, including mechanical and thermal properties, water absorption, and morphological characteristics.

POLYMER COMPOSITES (2021)

Add to Collection

Article Materials Science, Composites

The effect of carbon nanotubes modified polyurethane adhesive on the impact behavior of sandwich structures

Mehmet Emin Cetin

Summary: Sandwich panels with aluminum honeycomb cores are widely used in various structural engineering areas due to their lightweight properties and high specific strength and stiffness. This study focuses on investigating the impact behavior of aluminum honeycomb sandwich panels with different core cell sizes using multi-walled carbon nanotube (MWCNT) reinforced polyurethane (PU) adhesives. The inclusion of MWCNTs in the PU adhesive enhances the impact performance of honeycomb sandwich structures, as evidenced by experimental testing and numerical simulations.

POLYMER COMPOSITES (2021)

Add to Collection

Article Engineering, Mechanical

Long-term salt-water durability of GNPs reinforced basalt-epoxy multiscale composites for marine applications

Emine Feyza Sukur et al.

Summary: The corrosion behavior and wear performance of basalt/epoxy composites exposed to salt-water were studied experimentally, as well as the impact of graphene nanoplatelet modification of the epoxy matrix on the composite's water absorption and wear performance. The results showed that the modification with GNPs reduced water absorption and coefficient of friction, while causing a smaller decrease in tensile strength and modulus of elasticity after the 6th month.

TRIBOLOGY INTERNATIONAL (2021)

Add to Collection

Article Materials Science, Composites

Halloysite nanotube reinforcement endows ameliorated fracture resistance of seawater aged basalt/epoxy composites

Hasan Ulus et al.

JOURNAL OF COMPOSITE MATERIALS (2020)

Add to Collection

Review Chemistry, Applied

Polysaccharides/Halloysite nanotubes for smart bionanocomposite materials

Vanessa Bertolino et al.

CARBOHYDRATE POLYMERS (2020)

Add to Collection

Article Engineering, Mechanical

Investigation of the concentration rate and aggregation behaviour of nano-silver added colloidal suspensions on wear behaviour of metallic materials by using ANOVA method

M. Huseyin Cetin et al.

TRIBOLOGY INTERNATIONAL (2020)

Add to Collection

Review Engineering, Mechanical

Surface topography modification, Film transfer and Wear mechanism for fibre reinforced polymer composites-An Overview

Meghashree Padhan et al.

SURFACE TOPOGRAPHY-METROLOGY AND PROPERTIES (2020)

Add to Collection

Article Engineering, Mechanical

Optimization of abrasive wear behaviour of halloysite nanotubes filled carbon fabric reinforced epoxy hybrid composites

B. Muralidhara et al.

SURFACE TOPOGRAPHY-METROLOGY AND PROPERTIES (2020)

Add to Collection

Article Polymer Science

Tribological and mechanical properties of polyamide-11/halloysite nanotube nanocomposites

Mohamed Sahnoune et al.

JOURNAL OF POLYMER ENGINEERING (2019)

Add to Collection

Article Materials Science, Coatings & Films

The influence of multiple fillers on friction and wear behavior of epoxy composite coatings

Yan Hao et al.

SURFACE & COATINGS TECHNOLOGY (2019)

Add to Collection

Article Materials Science, Composites

Flexural properties of notched carbon-aramid hybrid composite laminates

T. A. Sebaey et al.

JOURNAL OF COMPOSITE MATERIALS (2019)

Add to Collection

Article Materials Science, Textiles

Enhanced Salty Water Durability of Halloysite Nanotube Reinforced Epoxy/Basalt Fiber Hybrid Composites

Hasan Ulus et al.

FIBERS AND POLYMERS (2019)

Add to Collection

Article Materials Science, Composites

Mechanical behavior and thermal stability of ultrasonically synthesized halloysite-epoxy composite

Shakun Srivastava et al.

COMPOSITES COMMUNICATIONS (2019)

Add to Collection

Article Engineering, Mechanical

Friction and Wear Performance of Epoxy Resin Reinforced With Boron Nitride Nanoplatelets

Mursel Ekrem et al.

JOURNAL OF TRIBOLOGY-TRANSACTIONS OF THE ASME (2018)

Add to Collection

Review Polymer Science

Review on Polymer/Halloysite Nanotube Nanocomposite

Ayesha Kausar

POLYMER-PLASTICS TECHNOLOGY AND ENGINEERING (2018)

Add to Collection

Article Chemistry, Physical

A structural comparison of halloysite nanotubes of different origin by Small-Angle Neutron Scattering (SANS) and Electric Birefringence

Giuseppe Cavallaro et al.

APPLIED CLAY SCIENCE (2018)

Add to Collection

Article Engineering, Multidisciplinary

Static and dynamic mechanical responses of CaCO3 nanoparticle modified epoxy/carbon fiber nanocomposites

Volkan Eskizeybek et al.

COMPOSITES PART B-ENGINEERING (2018)

Add to Collection

Article Engineering, Multidisciplinary

Nano-silica inclusion effects on mechanical and dynamic behavior of fiber reinforced carbon/Kevlar with epoxy resin hybrid composites

Mohamad Alsaadi et al.

COMPOSITES PART B-ENGINEERING (2018)

Add to Collection

Article Engineering, Mechanical

A novel approach to minimize dry sliding friction and wear behavior of epoxy by infusing fullerene C70 and multiwalled carbon nanotubes

R. K. Upadhyay et al.

TRIBOLOGY INTERNATIONAL (2018)

Add to Collection

Article Materials Science, Composites

Physical and Mechanical Behavior of Unidirectional Banana/Jute Fiber Reinforced Epoxy Based Hybrid Composites

Siva Bhaskara Rao Devireddy et al.

POLYMER COMPOSITES (2017)

Add to Collection

Article Food Science & Technology

Halloysite Nanotubes/Polyethylene Nanocomposites for Active Food Packaging Materials with Ethylene Scavenging and Gas Barrier Properties

C. Erdinc Tas et al.

FOOD AND BIOPROCESS TECHNOLOGY (2017)

Add to Collection

Article Engineering, Mechanical

Tribological performance of halloysite clay nanotubes as green lubricant additives

Laura Pena-Paras et al.

WEAR (2017)

Add to Collection

Article Engineering, Multidisciplinary

Evaluating the effectiveness of nanofillers in filament wound carbon/epoxy multiscale composite pipes

Tugay Ustun et al.

COMPOSITES PART B-ENGINEERING (2016)

Add to Collection

Article Engineering, Multidisciplinary

High strain-rate failure in carbon/Kevlar hybrid woven composites via a novel SHPB-AE coupled test

Sung-Choong Woo et al.

COMPOSITES PART B-ENGINEERING (2016)

Add to Collection

Article Engineering, Mechanical

Variation of the tribological properties of carbon fabric composites in their whole service life

Fei Jie et al.

TRIBOLOGY INTERNATIONAL (2016)

Add to Collection

Article Chemistry, Multidisciplinary

High thermal conductivity and high impact strength of epoxy nanodielectrics with functionalized halloysite nanotubes

Hailin Mo et al.

RSC ADVANCES (2016)

Add to Collection

Article Materials Science, Composites

Three-Body Abrasive Wear Behavior of Short Jute Fiber Reinforced Epoxy Composites

Vivek Mishra et al.

POLYMER COMPOSITES (2016)

Add to Collection

Article Engineering, Aerospace

Design of a hybrid carbon fibre/carbon nanotube composite for enhanced lightning strike resistance

Xiang Ma et al.

AEROSPACE SCIENCE AND TECHNOLOGY (2015)

Add to Collection

Article Engineering, Mechanical

Friction and wear behaviors of carbon and aramid fibers reinforced polyimide composites in simulated space environment

Mei Lv et al.

TRIBOLOGY INTERNATIONAL (2015)

Add to Collection

Article Engineering, Mechanical

Enhancement of Wear and Friction Characteristics of Epoxy Resin by Multiwalled Carbon Nanotube and Boron Nitride Nanoparticles

Hayrettin Duzcukoglu et al.

TRIBOLOGY TRANSACTIONS (2015)

Add to Collection

Article Materials Science, Composites

Scratch behavior of glass fiber reinforced polyester matrix composite after solid particle erosion

Mustafa Ozgur Bora et al.

POLYMER COMPOSITES (2015)

Add to Collection

Article Materials Science, Composites

Hybrid fiber reinforced polymer composites - a review

T. P. Sathishkumar et al.

JOURNAL OF REINFORCED PLASTICS AND COMPOSITES (2014)

Add to Collection

Review Polymer Science

Recent advance in research on halloysite nanotubes-polymer nanocomposite

Mingxian Liu et al.

PROGRESS IN POLYMER SCIENCE (2014)

Add to Collection

Article Engineering, Manufacturing

Effects of unfolded and intercalated halloysites on mechanical properties of halloysite-epoxy nanocomposites

Youhong Tang et al.

COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2011)

Add to Collection

Article Polymer Science

Processing and characterization of halloysite nanotubes filled polypropylene nanocomposites based on a masterbatch route: effect of halloysites treatment on structural and mechanical properties

K. Prashantha et al.

EXPRESS POLYMER LETTERS (2011)

Add to Collection

Review Polymer Science

Newly emerging applications of halloysite nanotubes: a review

Mingliang Du et al.

POLYMER INTERNATIONAL (2010)

Add to Collection

Article Materials Science, Composites

Halloysite-epoxy nanocomposites with improved particle dispersion through ball mill homogenisation and chemical treatments

Shiqiang Deng et al.

COMPOSITES SCIENCE AND TECHNOLOGY (2009)

Add to Collection

Article Materials Science, Composites

Effect of Surface Treatment on the Tribological Performance of Carbon Fiber Reinforced Thermoplastic Polyimide Composites

J. Li et al.

POLYMER COMPOSITES (2009)

Add to Collection

Article Nanoscience & Nanotechnology

Tribological properties of three-dimensional braided carbon/Kevlar/epoxy hybrid composites under dry and lubricated conditions

Y. Z. Wan et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2007)

Add to Collection

Article Mechanics

Temperature effects on Kevlar/hybrid and carbon fiber composite sandwiches under impact loading

Amin Salehi-Khojin et al.

COMPOSITE STRUCTURES (2007)

Add to Collection

Article Engineering, Mechanical

Comparison of friction and wear for an epoxy resin reinforced by a glass or a carbon/aramid hybrid weave

Thomas O. Larsen et al.

WEAR (2007)

Add to Collection

Article Chemistry, Multidisciplinary

Toughening, thermal stability, flame retardancy, and scratch-wear resistance of polymer-clay nanocomposites

Aravind Dasari et al.

AUSTRALIAN JOURNAL OF CHEMISTRY (2007)

Add to Collection

Article Engineering, Mechanical

Hot wear properties of ceramic and basalt fiber reinforced hybrid friction materials

Bulent Ozturk et al.

TRIBOLOGY INTERNATIONAL (2007)

Add to Collection

Article Engineering, Mechanical

Tribological behaviour of clay - thermoset polyester nanocomposites

P. Jawahar et al.

WEAR (2006)

Add to Collection

Article Materials Science, Composites

Wear behavior of carbon fiber-reinforced poly(phenylene sulfide)

J Quintelier et al.

POLYMER COMPOSITES (2006)

Add to Collection

Article Polymer Science

Thermal stability and flame retardant effects of halloysite nanotubes on poly(propylene)

Mingliang Du et al.

EUROPEAN POLYMER JOURNAL (2006)

Add to Collection

Article Nanoscience & Nanotechnology

Effect of wear on interface frictional resistance in fiber-reinforced composite: model experimental

H Kakisawa et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2000)

Add to Collection

© Peeref 2019-2024. All rights reserved.