Related references
Note: Only part of the references are listed.Drilling induced defects on carbon fiber-reinforced thermoplastic polyamide and their effect on mechanical properties
Dieter Meinhard et al.
COMPOSITE STRUCTURES (2021)
Study on machining characteristics of magnetically controlled laser induced plasma micro-machining single-crystal silicon
Yanming Zhang et al.
JOURNAL OF ADVANCED RESEARCH (2021)
Drilling of CFRP plates with adjustable pulse duration fiber laser
Wenyuan Li et al.
MATERIALS AND MANUFACTURING PROCESSES (2021)
The influence of machining processes on strain distribution and progressive failure characteristics when producing holes in CFRP
Maojun Li et al.
COMPOSITE STRUCTURES (2020)
Stretchability improvement of flexiable electronics by laser micro-drilling array holes in PDMS film
Youmin Rong et al.
OPTICS AND LASERS IN ENGINEERING (2020)
The fatigue of carbon fibre reinforced plastics - A review
Parvez Alam et al.
COMPOSITES PART B-ENGINEERING (2019)
Laser beam machining of carbon fiber reinforced composites: a review
M. H. El-Hofy et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2019)
Experimental and numerical analysis of step drill bit performance when drilling woven CFRPs
N. Feito et al.
COMPOSITE STRUCTURES (2018)
Heat affected zone extension in pulsed Nd:YAG laser cutting of CFRP
C. Leone et al.
COMPOSITES PART B-ENGINEERING (2018)
Thermoplastic-Toughened High-Temperature Cyanate Esters and Their Application in Advanced Composites
Ahmed Inamdar et al.
INDUSTRIAL & ENGINEERING CHEMISTRY RESEARCH (2018)
Study on burr occurrence and surface integrity during slot milling of multidirectional and plain woven CFRPs
Maojun Li et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2018)
Thermal, mechanical and chemical material removal mechanism of carbon fiber reinforced polymers in electrical discharge machining
Xiaoming Yue et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2018)
Experimental study on the picosecond pulsed laser cutting of carbon fiber-reinforced plastics
Jun Hu et al.
JOURNAL OF REINFORCED PLASTICS AND COMPOSITES (2018)
Drill-exit temperature characteristics in drilling of UD and MD CFRP composites based on infrared thermography
Rao Fu et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2018)
Surface treatment of CFRP composites using femtosecond laser radiation
V. Oliveira et al.
OPTICS AND LASERS IN ENGINEERING (2017)
Three-dimensional numerical simulation during laser processing of CFRP
Tomomasa Ohkubo et al.
APPLIED SURFACE SCIENCE (2017)
An experimental study on abrasive waterjet cutting of CFRP/Ti6Al4V stacks for drilling operations
A. Alberdi et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2016)
High-power picosecond laser drilling/machining of carbon fibre-reinforced polymer (CFRP) composites
A. Salama et al.
APPLIED PHYSICS A-MATERIALS SCIENCE & PROCESSING (2016)
Heat conduction analysis of laser CFRP processing with IR and UV laser light
K. Takahashi et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2016)
Novel drill structure for damage reduction in drilling CFRP composites
Zhenyuan Jia et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2016)
Influence of electrical discharge machining parameters on cutting parameters of carbon fiber-reinforced plastic
Sameh Habib et al.
MACHINING SCIENCE AND TECHNOLOGY (2016)
High Performance Cutting of Fibre Reinforced Plastic Composite Materials
V. Lopresto et al.
7TH HPC 2016 - CIRP CONFERENCE ON HIGH PERFORMANCE CUTTING (2016)
Characterization of hole circularity and heat affected zone in pulsed CO2 laser drilling of alumina ceramics
A. Bharatish et al.
OPTICS AND LASER TECHNOLOGY (2013)
Experimental study on the CO2 laser cutting of carbon fiber reinforced plastic composite
A. Riveiro et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2012)
A study on UV laser drilling of PEEK reinforced with carbon fibers
L. Romoli et al.
OPTICS AND LASERS IN ENGINEERING (2012)
Study on UV laser machining quality of carbon fibre reinforced composites
Z. L. Li et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2010)
A study of delamination on graphite/epoxy composites in abrasive waterjet machining
D. K. Shanmugam et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2008)
Composite degradation due to fluid absorption
G Sala
COMPOSITES PART B-ENGINEERING (2000)
Share Paper
