Related references
Note: Only part of the references are listed.Fatigue performance improvement of laser shock peened hole on powder metallurgy Ni-based superalloy labyrinth disc
Xinlei Pan et al.
SURFACE & COATINGS TECHNOLOGY (2021)
Effect of laser shock peening on the hot corrosion behavior of Ni-based single-crystal superalloy at 750 °C
Yongxiang Geng et al.
CORROSION SCIENCE (2021)
Evolutions of microstructure, phase, microhardness, and residual stress of multiple laser shock peened Ni-based single crystal superalloy after short-term thermal exposure
Yongxiang Geng et al.
OPTICS AND LASER TECHNOLOGY (2020)
Effect of laser shock peening on mechanical and microstructural aspects of 6061-T6 aluminum alloy
Binod Dhakal et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2020)
Thermal stress relaxation in shot peened and laser peened nickel-based superalloy
K. S. Chin et al.
JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2020)
Influences of solution cooling on microstructures, mechanical properties and hot corrosion resistance of a nickel-based superalloy
Dao-Guang He et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2019)
Measurement of residual stresses in titanium alloys using synchrotron radiation
A. Umapathi et al.
MEASUREMENT (2019)
Oxidation behavior of a single-crystal Ni-based superalloy over the temperature range of 850 °C-950 °C in air
Yebing Hu et al.
APPLIED SURFACE SCIENCE (2019)
Study on the effect of multiple laser shock peening on residual stress and microstructural changes in modified 9Cr-1Mo (P91) steel
Arun Kumar Rai et al.
SURFACE & COATINGS TECHNOLOGY (2019)
Re segregation at interfacial dislocation network in a nickel-based superalloy
Qingqing Ding et al.
ACTA MATERIALIA (2018)
Evolutions of microstructure and lattice misfit in a gamma '-rich Ni-based superalloy during ultra-high temperature thermal cycle
Liang Luo et al.
INTERMETALLICS (2018)
Microstructure, residual stress and tensile properties control of wire-arc additive manufactured 2319 aluminum alloy with laser shock peening
Rujian Sun et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2018)
Influence of temperature on the lattice misfit and elastic moduli of a Ni based single crystal superalloy with high volume fraction of gamma ' phase
Liang Luo et al.
MATERIALS CHARACTERIZATION (2018)
The effect of chromium and cobalt segregation at dislocations on nickel-based superalloys
Paraskevas Kontis et al.
SCRIPTA MATERIALIA (2018)
Improving creep properties of 7075 aluminum alloy by laser shock peening
J. T. Wang et al.
SURFACE & COATINGS TECHNOLOGY (2018)
Effect of shot peening on the fatigue properties of nickel-based superalloy GH4169 at high temperature
Xiaohui Zhao et al.
RESULTS IN PHYSICS (2018)
Thermal evolution of residual stress in IN718 alloy subjected to laser peening
Suqiang Xu et al.
OPTICS AND LASERS IN ENGINEERING (2017)
Improvement in mechanical properties of titanium alloy (Ti-6Al-7Nb) subject to multiple laser shock peening
Xiaojun Shen et al.
SURFACE & COATINGS TECHNOLOGY (2017)
Selective evolution of secondary γ' precipitation in a Ni-based single crystal superalloy both in the γ matrix and at the dislocation nodes
Sisi Xiang et al.
ACTA MATERIALIA (2016)
Effect of laser shock peening on microstructure and fatigue crack growth rate of AZ31B magnesium alloy
Mao-Zhong Ge et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2016)
Effects of laser shock processing on microstructure and mechanical properties of K403 nickel-alloy
C. Wang et al.
MATERIALS & DESIGN (2016)
Effect of skew angle of holes on the tensile behavior of a Ni-base single crystal superalloy
Z. J. Zhou et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2015)
Residual stress determination in a shot-peened nickel-based single-crystal superalloy using X-ray diffraction
Amelie Morancais et al.
JOURNAL OF APPLIED CRYSTALLOGRAPHY (2015)
Coupling between Re segregation and γ/γ′ interfacial dislocations during high-temperature, low-stress creep of a nickel-based single-crystal superalloy
Ming Huang et al.
ACTA MATERIALIA (2014)
Large stress concentrations around micropore near a crack-tip induced deformation twinning in Ni-based single crystal superalloy
Fei Sun et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2014)
Ultrahigh dense and gradient nano-precipitates generated by warm laser shock peening for combination of high strength and ductility
Chang Ye et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2014)
Experimental and numerical investigation of material heterogeneity in shot peened aluminium alloy AA2024-T351
A. Gariepy et al.
SURFACE & COATINGS TECHNOLOGY (2013)
Fatigue performance improvement in AISI 4140 steel by dynamic strain aging and dynamic precipitation during warm laser shock peening
Chang Ye et al.
ACTA MATERIALIA (2011)
Dislocation pinning effects induced by nano-precipitates during warm laser shock peening: Dislocation dynamic simulation and experiments
Yiliang Liao et al.
JOURNAL OF APPLIED PHYSICS (2011)
Nucleation of highly dense nanoscale precipitates based on warm laser shock peening
Yiliang Liao et al.
JOURNAL OF APPLIED PHYSICS (2010)
Effects of laser shock processing on stress corrosion cracking susceptibility of AZ31B magnesium alloy
Yongkang Zhang et al.
SURFACE & COATINGS TECHNOLOGY (2010)
Influence of local chemical segregation on the gamma ' directional coarsening behavior in single crystal superalloy CMSX-4
K. Y. Cheng et al.
MATERIALS CHARACTERIZATION (2009)
Observation of giant diffusivity along dislocation cores
Marc Legros et al.
SCIENCE (2008)
Methods for obtaining the strain-free lattice parameter when using diffraction to determine residual stress
P. J. Withers et al.
JOURNAL OF APPLIED CRYSTALLOGRAPHY (2007)
Microstructure and stress rupture properties of single crystal superalloy CMSX-2 under high thermal gradient directional solidification
L. Liu et al.
MATERIALS LETTERS (2007)
Share Paper
