Related references
Note: Only part of the references are listed.On the effect of plastic anisotropy, strength and work hardening on the tensile ductility of aluminium alloys
Bjorn Hakon Frodal et al.
INTERNATIONAL JOURNAL OF SOLIDS AND STRUCTURES (2020)
A phenomenological model based on nanostructured dislocation cluster interactions to predict the work hardening behavior of cryodeformed materials
B. Srinivas et al.
INTERNATIONAL JOURNAL OF PLASTICITY (2020)
Significance of stacking fault energy in bulk nanostructured materials: Insights from Cu and its binary alloys as model systems
X. H. An et al.
PROGRESS IN MATERIALS SCIENCE (2019)
Modeling the mechanical behavior of heterogeneous ultrafine grained polycrystalline and nanocrystalline FCC metals
A. Abdul-Latif et al.
MECHANICS OF MATERIALS (2018)
A mathematical prediction model to establish the role of stacking fault energy on the cryo-deformation behavior of FCC materials at different strain levels
B. Srinivas et al.
INTERNATIONAL JOURNAL OF PLASTICITY (2017)
Effect of cryorolling on microstructure and mechanical properties of a peak-aged AA6082 extrusion
Zebing Xu et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2017)
Two phenomenological models to predict the single peak flow stress curves up to the peak during hot deformation
Soheil Solhjoo et al.
MECHANICS OF MATERIALS (2017)
Structural and phase transformation in a TWIP steel subjected to high pressure torsion
M. M. Abramova et al.
MATERIALS LETTERS (2016)
Precipitation phenomena, thermal stability and grain growth kinetics in an ultra-fine grained Al 2014 alloy after annealing treatment
A. Dhal et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2015)
Effects of rolling temperature and subsequent annealing on mechanical properties of ultrafine-grained Cu-Zn-Si alloy
Xiangkai Zhang et al.
MATERIALS CHARACTERIZATION (2015)
Influence of annealing on stain hardening behaviour and fracture properties of a cryorolled Al 2014 alloy
A. Dhal et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2015)
Significant contribution of stacking faults to the strain hardening behavior of Cu-15%Al alloy with different grain sizes
Y. Z. Tian et al.
SCIENTIFIC REPORTS (2015)
Stacking fault and partial dislocation dominated strengthening mechanisms in highly textured Cu/Co multilayers
Y. Liu et al.
INTERNATIONAL JOURNAL OF PLASTICITY (2013)
High-Strain-Rate Deformation: Mechanical Behavior and Deformation Substructures Induced
George T. (Rusty) Gray
ANNUAL REVIEW OF MATERIALS RESEARCH, VOL 42 (2012)
Enhanced strength-ductility synergy in nanostructured Cu and Cu-Al alloys processed by high-pressure torsion and subsequent annealing
X. H. An et al.
SCRIPTA MATERIALIA (2012)
Effect of stacking fault energy on deformation behavior of cryo-rolled copper and copper alloys
H. Bahmanpour et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2011)
A dislocation-based constitutive description for modeling the behavior of FCC metals within wide ranges of strain rate and temperature
J. A. Rodriguez-Martinez et al.
MECHANICS OF MATERIALS (2011)
Exceptionally high strength in Mg-3Al-1Zn alloy processed by high-ratio differential speed rolling
W. J. Kim et al.
SCRIPTA MATERIALIA (2011)
Microstructural response of pure copper to cryogenic rolling
T. Konkova et al.
ACTA MATERIALIA (2010)
Deformation twinning mechanism and its effects on the mechanical behaviors of ultrafine grained and nanocrystalline copper
Feng Shen et al.
COMPUTATIONAL MATERIALS SCIENCE (2010)
Effect of rolling temperature on the evolution of defects and properties of an Al-Cu alloy
V. Subramanya Sarma et al.
JOURNAL OF MATERIALS SCIENCE (2010)
Microstructural evolution and shear fracture of Cu-16 at.% Al alloy induced by equal channel angular pressing
X. H. An et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2010)
Correlation between the behavior of nanocrystalline HCP metals and the dislocation model for the minimum grain size obtainable by milling
Farghalli A. Mohamed
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2010)
Influence of stacking fault energy and short-range ordering on dynamic recovery and work hardening behavior of copper alloys
Farzad Hamdi et al.
SCRIPTA MATERIALIA (2010)
Modelling discontinuous dynamic recrystallization using a physically based model for nucleation
D. G. Cram et al.
ACTA MATERIALIA (2009)
Friction behaviour evaluation in beryllium-copper threaded connections
S. Baragetti et al.
INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2009)
Stress-strain behaviour of aluminium alloys at a wide range of strain rates
Y. Chen et al.
INTERNATIONAL JOURNAL OF SOLIDS AND STRUCTURES (2009)
Influence of stacking-fault energy on the accommodation of severe shear strain in Cu-Al alloys during equal-channel angular pressing
Xianghai An et al.
JOURNAL OF MATERIALS RESEARCH (2009)
Microstructure and mechanical properties of ultra fine grained Cu-Zn and Cu-Al alloys produced by cryorolling and annealing
V. Subramanya Sarma et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2008)
Determining the optimal stacking fault energy for achieving high ductility in ultrafine-grained Cu-Zn alloys
Y. H. Zhao et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2008)
Dislocation mean free paths and strain hardening of crystals
B. Devincre et al.
SCIENCE (2008)
Simultaneously increasing the ductility and strength of ultra-fine-grained pure copper
Yong-Hao Zhao et al.
ADVANCED MATERIALS (2006)
Applicability of the groove pressing technique for grain refinement in commercial purity copper
A Krishnaiah et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2005)
On the mechanisms of dynamic recovery
E Nes et al.
SCRIPTA MATERIALIA (2002)
High tensile ductility in a nanostructured metal
YM Wang et al.
NATURE (2002)
Share Paper
