☆ 4.7 Article

Effect of Y addition on microstructure evolution and precipitation of Cu-Co-Si alloy during hot deformation

MATERIALS CHARACTERIZATION (2021)

Related references

Note: Only part of the references are listed.

Article Engineering, Mechanical

Flow characterization of magnesium alloy ZK61 during hot deformation with improved constitutive equations and using activation energy maps

Jinchuan Long et al.

Summary: This study characterized the flow characteristics and workability of as-extruded magnesium alloy ZK61 through isothermal compression tests. Flow stress curves were analyzed, and both conventional and improved Arrhenius constitutive equations were developed to predict flow characteristics. Activation energy maps identified dominant deformation mechanisms and optimal processing conditions for the alloy.

INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2021)

Add to Collection

Article Engineering, Industrial

Characterization of microstructures and hot-compressive behavior of GH4169 superalloy by kinetics analysis and simulation

Peihao Geng et al.

Summary: The study revealed that dynamic recrystallization (DRX) behavior was promoted at higher temperatures and lower strain rates, and no 8 phase existed at or above 1333 K deformation temperature. A significant yield drop occurred within the temperature range varying from 1273 K to 1333 K due to the dissolution of the 8 phase and enhanced mobility of defects.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Effect of Zn content on the dynamic softening of Al-Zn-Mg-Cu alloys during hot compression deformation

Jie Tang et al.

Summary: Increasing Zn content in Al-Zn-Mg-Cu alloys accelerates work hardening rate but has a mixed effect on peak stress and hot deformation activation energy. Dynamic softening increases gradually with higher Zn content due to accelerated dynamic precipitation, while it decreases with low Zn content as dynamic recovery and recrystallization are hindered by Zn addition.

VACUUM (2021)

Add to Collection

Article Materials Science, Multidisciplinary

Effects of strain rates on dynamic deformation behavior of Cu-20Ag alloy

Kexing Song et al.

Summary: Copper alloy is widely used in high-speed railway, aerospace and other fields due to its excellent electrical conductivity and mechanical properties. Increase of strain rate can reduce the adiabatic shear sensitivity and promote the precipitation of Ag in Cu-20Ag alloy, which in turn improves the strength of the alloy.

JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2021)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Hot deformation behavior of Ti-6Al-4V-0.1Ru alloy during isothermal compression

Yu-feng Xia et al.

TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2020)

Add to Collection

Article Materials Science, Multidisciplinary

Effects of Cr addition on the constitutive equation and precipitated phases of copper alloy during hot deformation

Yijie Ban et al.

MATERIALS & DESIGN (2020)

Add to Collection

Review Materials Science, Multidisciplinary

A review of microstructure and texture evolution with nanoscale precipitates for copper alloys

Yongfeng Geng et al.

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T (2020)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Microstructure evolution and hot deformation behavior of Cu-3Ti-0.1Zr alloy with ultra-high strength

Xu Wang et al.

TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2020)

Add to Collection

Article Materials Science, Multidisciplinary

EBSD analysis of hot deformation behavior of Cu-Ni-Co-Si-Cr alloy

YiJie Ban et al.

MATERIALS CHARACTERIZATION (2020)

Add to Collection

Article Metallurgy & Metallurgical Engineering

Effect of Si and Ti on dynamic recrystallization of high-performance Cu-15Ni-8Sn alloy during hot deformation

Chao Zhao et al.

TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA (2019)

Add to Collection

Article Chemistry, Multidisciplinary

Cr effects on the electrical contact properties of the Al2O3-Cu/15W composites

Xiaohui Zhang et al.

NANOTECHNOLOGY REVIEWS (2019)

Add to Collection

Article Materials Science, Multidisciplinary

Influence of deformation and annealing twinning on the microstructure and texture evolution of face-centered cubic high-entropy alloys

Christian Haase et al.

ACTA MATERIALIA (2018)

Add to Collection

Article Materials Science, Multidisciplinary

Effects of Ce addition on the Cu-Mg-Fe alloy hot deformation behavior

Bingjie Wang et al.

VACUUM (2018)

Add to Collection

Article Crystallography

Aging Behavior and Precipitation Analysis of Cu-Ni-Co-Si Alloy

Xiangpeng Xiao et al.

CRYSTALS (2018)

Add to Collection

Article Nanoscience & Nanotechnology

Deformation microstructures, strengthening mechanisms, and electrical conductivity in a Cu-Cr-Zr alloy

R. Mishnev et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2015)

Add to Collection

Article Nanoscience & Nanotechnology

Dynamic recrystallisation and precipitation behaviour of high strength and highly conducting Cu-Ag-Zr-alloys

F. Bittner et al.

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2014)

Add to Collection

© Peeref 2019-2024. All rights reserved.