☆ 4.5 Article

Hydrodynamic arc moving mechanism in EDM of polycrystalline diamond

MATERIALS AND MANUFACTURING PROCESSES (2022)

Related references

Note: Only part of the references are listed.

Article Engineering, Manufacturing

Exploration of MFOA in PAC parameters on machining Inconel 718

M. Karthick et al.

Summary: This study optimized the parameters of plasma arc cutting of Inconel 718 superalloy sheet through response surface analysis, finding that the MFO algorithm was feasible in predicting and optimizing the PAC process to achieve the optimal processing conditions.

MATERIALS AND MANUFACTURING PROCESSES (2022)

Add to Collection

Article Engineering, Manufacturing

Experimental research on single-pulse discharge crater morphology in SEAM

Xiaokang Chen et al.

Summary: This study investigates the effects of voltage and pulse duration under different polarities on the characteristics of craters in SEAM through single-pulse discharge experiments. The results show that increasing voltage and pulse duration lead to larger crater diameter, wider and deeper recast layer, higher bulge height, while negative-polarity machining tends to form larger and shallower craters with lower surface roughness and positive-polarity machining tends to form smaller and deeper craters with higher machining efficiency.

MATERIALS AND MANUFACTURING PROCESSES (2022)

Add to Collection

Article Engineering, Manufacturing

Super Dielectric Based EDM Process for Drilling of Inconel 718

M. Tanjilul et al.

Summary: The study proposes a novel super dielectric for EDM drilling process, demonstrating significant improvement in machining efficiency for deep hole drilling. Experimental observations on the effect of super dielectric fluid on plasma current are validated through plasma physics theory, with successful drilling holes of aspect ratio more than 100 in Inconel 718 within 6 minutes.

MATERIALS AND MANUFACTURING PROCESSES (2021)

Add to Collection

Article Engineering, Manufacturing

Motion Characteristics of Discharge Channel in WEDM

Yueqin Zhang et al.

Summary: The study reveals that the motion speed of the discharge channel in wire-cut EDM initially increases, then sharply decreases, and eventually stabilizes. The duration of the discharge significantly affects the average moving speed and diameter of the discharge channel.

MATERIALS AND MANUFACTURING PROCESSES (2021)

Add to Collection

Article Engineering, Manufacturing

Machining of 7Cr13Mo steel by US-PMEDM process

W. Zhang et al.

Summary: The study investigated the machining characteristics of 7Cr13Mo steel using ultrasonic-assisted and powder-mixed electrical discharge machining (US-PMEDM), and found that this process improved surface quality, material removal rate, and micro hardness compared to traditional EDM.

MATERIALS AND MANUFACTURING PROCESSES (2021)

Add to Collection

Article Engineering, Manufacturing

The influence of additive powder on machinability and surface integrity of SKD61 steel by EDM process

Van Tao Le

Summary: PMEDM technology, by adjusting key parameters such as peak current, pulse on time, and powder concentration, can influence material removal rate, tool wear rate, and surface integrity. The study shows that under certain conditions, MRR and TWR will increase, while PSCDA and RLT will significantly reduce.

MATERIALS AND MANUFACTURING PROCESSES (2021)

Add to Collection

Article Automation & Control Systems

Study on arc plasma movement and its effect on crater morphology during single-pulse discharge in EDM

Qi Li et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2020)

Add to Collection

Article Engineering, Manufacturing

Moving arc electrical discharge machining of polycrystalline diamond

Xiangzhi Wang et al.

MATERIALS AND MANUFACTURING PROCESSES (2020)

Add to Collection

Article Engineering, Manufacturing

Machining characteristics of PCD by EDM with Cu-Ni composite electrode

Y. L. Teng et al.

MATERIALS AND MANUFACTURING PROCESSES (2020)

Add to Collection

Article Engineering, Industrial

Active gap capacitance electrical discharge machining of polycrystalline diamond

Xiangzhi Wang et al.

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2020)

Add to Collection

Article Engineering, Manufacturing

Alternating Energy Electrical Discharge Machining of Titanium Alloy Using a WC-PCD Electrode

Xiangzhi Wang et al.

JOURNAL OF MANUFACTURING PROCESSES (2020)

Add to Collection

Article Automation & Control Systems

Thermo-electrical coupling simulation of powder mixed EDM SiC/Al functionally graded materials

L. Tang et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2019)

Add to Collection

Article Engineering, Manufacturing

Improvement of Wire Electrical Discharge Machining Characteristics in Machining Boron-doped Polycrystalline Diamond Using a Novel Iso-pulse Generator

Mu-Tian Yan et al.

INTERNATIONAL JOURNAL OF PRECISION ENGINEERING AND MANUFACTURING (2019)

Add to Collection

Article Engineering, Industrial

Modeling study of the hydrodynamic arc breaking mechanism in BEAM

Wansheng Zhao et al.

CIRP ANNALS-MANUFACTURING TECHNOLOGY (2018)

Add to Collection

Article Automation & Control Systems

A study of the material removal mechanism of polycrystalline diamond in electrical discharge machining based on spectroscopic measurement

Jialin Liu et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2018)

Add to Collection

Article Engineering, Manufacturing

Wear Mechanism and Modeling of Tribological Behavior of Polycrystalline Diamond Tools When Cutting Ti6Al4V

Guangxian Li et al.

JOURNAL OF MANUFACTURING SCIENCE AND ENGINEERING-TRANSACTIONS OF THE ASME (2018)

Add to Collection

Article Automation & Control Systems

Electrical discharge grinding versus abrasive grinding in polycrystalline diamond machining-tool quality and performance analysis

Mohammad Zulafif Rahim et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2016)

Add to Collection

Article Engineering, Manufacturing

Electrical discharge grinding of polycrystalline diamond - Effect of wheel rotation

M. Zulafif Rahim et al.

MACHINING SCIENCE AND TECHNOLOGY (2016)

Add to Collection

Proceedings Paper Electrochemistry

Electrical Discharge Machining of PCD in Ultrapure Water

Daisuke Yanagida et al.

18TH CIRP CONFERENCE ON ELECTRO PHYSICAL AND CHEMICAL MACHINING (ISEM XVIII) (2016)

Add to Collection

Article Engineering, Industrial

Micro-electrical discharge machining of polycrystalline diamond using rotary cupronickel electrode

Jiwang Yan et al.

CIRP ANNALS-MANUFACTURING TECHNOLOGY (2014)

Add to Collection

Article Engineering, Manufacturing

Mechanism of Electrical Discharge Machining Ablation

Xiangzhi Wang et al.

MATERIALS AND MANUFACTURING PROCESSES (2014)

Add to Collection

Article Automation & Control Systems

An experimental study on micro wire-EDM of polycrystalline diamond using a novel pulse generator

Mu-Tian Yan et al.

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2013)

Add to Collection

Article Engineering, Manufacturing

Parametric study on near-dry wire electrodischarge machining of polycrystalline diamond-coated tungsten carbide material

Y. Jia et al.

PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE (2010)

Add to Collection

Article Engineering, Manufacturing

High-speed EDM milling with moving electric arcs

Fuzhu Han et al.

INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2009)

Add to Collection

Article Engineering, Manufacturing

CNC electrical discharge rough machining of turbine blades

S. Ding et al.

PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE (2006)

Add to Collection

© Peeref 2019-2024. All rights reserved.