Related references
Note: Only part of the references are listed.Al0.3CrxFeCoNi high-entropy alloys with high corrosion resistance and good mechanical properties
Xiaolei Yan et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2021)
Oxidation behavior of CoCrFeMnNi high entropy alloy after plastic deformation
Ying Wang et al.
CORROSION SCIENCE (2020)
High cycle fatigue deformation mechanisms of a single phase CrMnFeCoNi high entropy alloy
M. Zare Ghomsheh et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)
Ultrahigh high-strain-rate superplasticity in a nanostructured high-entropy alloy
Nhung Thi-Cam Nguyen et al.
NATURE COMMUNICATIONS (2020)
Transformation-enhanced strength and ductility in a FeCoCrNiMn dual phase high-entropy alloy
T. Zhang et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)
Cryogenic mechanical behaviors of CrMnFeCoNi high-entropy alloy
Wujing Fu et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2020)
Shear punching of bulk metallic glasses under low stress
Fei Sun et al.
MATERIALS & DESIGN (2020)
Comparative corrosion behavior of Fe50Mn30Co10Cr10 dual-phase high-entropy alloy and CoCrFeMnNi high-entropy alloy in 3.5 wt% NaCl solution
Che-Wei Lu et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2020)
Microstructure and mechanical properties of FexCoCrNiMn high-entropy alloys
Tao Zhang et al.
JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY (2019)
Precipitation hardening in CoCrFeNi-based high entropy alloys
W. H. Liu et al.
MATERIALS CHEMISTRY AND PHYSICS (2018)
Microstructural evolution and high temperature mechanical properties of cast Al-15Mg2Si-xGd in situ composites
R. Khorshidi et al.
JOURNAL OF ALLOYS AND COMPOUNDS (2017)
Punch structure, punch wear and cut profiles of AISI 304 stainless steel sheet blanks manufactured using cryogenically treated AISI D3 tool steel punches
Yusuf Arslan et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2016)
Enhancing radiation tolerance by controlling defect mobility and migration pathways in multicomponent single-phase alloys
Chenyang Lu et al.
NATURE COMMUNICATIONS (2016)
An assessment on the future development of high-entropy alloys: Summary from a recent workshop
Z. P. Lu et al.
INTERMETALLICS (2015)
Relative effects of enthalpy and entropy on the phase stability of equiatomic high-entropy alloys
F. Otto et al.
ACTA MATERIALIA (2013)
Dynamic shear punching of metallic glass matrix composites
J. W. Qiao et al.
INTERMETALLICS (2013)
Shear punching of a Ti-based bulk metallic glass
Yongjiang Huang et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2013)
Assessment of anisotropic tensile strength using a modified shear punch test for Cu-Cr-Zr alloy processed by severe plastic deformation
Rixian Ding et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2013)
Solid-solution phase formation rules for multi-component alloys
Yong Zhang et al.
ADVANCED ENGINEERING MATERIALS (2008)
Finite elements simulations of thin copper sheets blanking: Study of blanking parameters on sheared edge quality
C. Husson et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2008)
Shear deformation capability of different metallic glasses
F. F. Wu et al.
JOURNAL OF MATERIALS RESEARCH (2008)
Multiplication of shear bands and ductility of metallic glass
F. F. Wu et al.
APPLIED PHYSICS LETTERS (2007)
Microstructural development in equiatomic multicomponent alloys
B Cantor et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2004)
Investigation on blanking of thin sheet metal using the ductile fracture criterion and its experimental verification
KH Shim et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2004)
Nanostructured high-entropy alloys with multiple principal elements: Novel alloy design concepts and outcomes
JW Yeh et al.
ADVANCED ENGINEERING MATERIALS (2004)
Prediction of optimum clearance in sheet metal blanking processes
R Hambli et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2003)
Finite element simulation of the effect of clearance on the forming quality in the blanking process
G Fang et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2002)