☆ 4.7 Article

Dynamic behavior and mechanism analysis of tip wetting process under flash boiling conditions

FUEL (2022)

Related references

Note: Only part of the references are listed.

Article Thermodynamics

The process of tip wetting at the spray injection end

Jerome Helie et al.

Summary: The study investigates various topics related to tip wetting in gasoline direct injection engines to identify the sources of carbon particles. Experimental identification of different phases of tip wetting is conducted, and phenomenological models are proposed.

INTERNATIONAL JOURNAL OF ENGINE RESEARCH (2021)

Add to Collection

Article Thermodynamics

Mechanisms of fuel injector tip wetting and tip drying based on experimental measurements of engine-out particulate emissions from gasoline direct-injection engines

M. Medina et al.

Summary: The study aims to simplify the conceptual understanding of injector tip wetting and drying mechanisms, and investigate the effects of different engine operating conditions and fuel injector geometries on these mechanisms. By comparing experimental results, it was found that increasing injected fuel mass leads to higher particulate number emissions, while longer hole length, lower speeds, early injection timings, and higher coolant temperature have the opposite effect.

INTERNATIONAL JOURNAL OF ENGINE RESEARCH (2021)

Add to Collection

Article Thermodynamics

Ultra-lean limit extension for gasoline direct injection engine application via high energy ignition and flash boiling atomization

Chang Ye et al.

Summary: This study explores the use of flash boiling atomization technique to improve spray atomization by elevating fuel temperature, combined with high energy ignition technique for better GDI engine performance under lean-burn conditions. Results show that flash boiling atomization extends the lean limit from 1.95 to 2.10, with impacts on key parameters and emissions.

PROCEEDINGS OF THE COMBUSTION INSTITUTE (2021)

Add to Collection

Article Thermodynamics

Split injection flash boiling spray for high efficiency and low emissions in a GDI engine under lean combustion condition *

Zhe Sun et al.

Summary: This study explores the use of flash boiling atomization to achieve a more homogeneous fuel-air mixture for lean combustion in a single cylinder engine. Imaging methods and traditional tests were utilized to evaluate engine performance, showing improved combustion efficiency and emission performance under flash boiling conditions, particularly with split injection schemes.

PROCEEDINGS OF THE COMBUSTION INSTITUTE (2021)

Add to Collection

Article Energy & Fuels

Differences in pool-fire induced soot production between subcooled spray and flash boiling spray in a DISI engine

Zhe Sun et al.

Summary: The study found that the combustion performance using flash boiling sprays is superior to that using subcooled sprays, and the difference between the two combustion modes was discussed with the use of a flame model.

FUEL (2021)

Add to Collection

Article Energy & Fuels

Evaporation and condensation of flash boiling sprays impinging on a cold surface

Di Xiao et al.

Summary: The study investigates the wall film formation when flash boiling sprays impinge on a cold surface, revealing that flash boiling impingement deposits less film mass on the wall compared to sub-cooled sprays, but still more than impinging on room temperature plate. With decreasing wall temperature, evaporation suppression and condensation effects become increasingly significant in dominating wall film formation.

FUEL (2021)

Add to Collection

Article Thermodynamics

Nozzle Tip Wetting in GDI Injector at Flash-boiling Conditions

Weidi Huang et al.

Summary: The study revealed that post-injected fuel caused by needle bouncing is a primary source of nozzle tip wetting under non-flash-boiling conditions. Rising fuel temperature under non-flash-boiling conditions does not significantly impact spray dynamics and tip wetting. Under flash-boiling conditions, nozzle tip wetting rapidly increases during fuel injection, reaching a maximum under transitional flash-boiling conditions.

INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER (2021)

Add to Collection

Article Thermodynamics

Effect of flash boiling injection on combustion and PN emissions of DISI optical engine fueled with butanol isomers/TPRF blends

Mohamed Nour et al.

Summary: Direct injection spark ignition (DISI) engines are widely used in passenger cars for their benefits, but suffer from issues such as wall wetting and excess emissions. By utilizing new fuel atomization techniques and biofuels, improvements can be made in combustion and emissions. Isobutanol and 2-butanol, along with blends with TPRF, were studied for their effects on spray characteristics and engine performance, showing promising results in reducing particle number emissions.

PROCEEDINGS OF THE COMBUSTION INSTITUTE (2021)

Add to Collection

Article Thermodynamics

Nozzle tip wetting in gasoline direct injection injector and its link with nozzle internal flow

Weidi Huang et al.

INTERNATIONAL JOURNAL OF ENGINE RESEARCH (2020)

Add to Collection

Review Energy & Fuels

A review on the experimental non-intrusive investigation of fuel injector phase changing flow

Shangze Yang et al.

FUEL (2020)

Add to Collection

Article Energy & Fuels

Quantitative investigation the influences of the injection timing under single and double injection strategies on performance, combustion and emissions characteristics of a GDI SI engine fueled with gasoline/ethanol blend

Xiongbo Duan et al.

FUEL (2020)

Add to Collection

Article Thermodynamics

Study of spray collapse phenomenon at flash boiling conditions using simultaneous front and side view imaging

Jianguo Du et al.

INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER (2020)

Add to Collection

Article Energy & Fuels

Flash boiling fuel initial disturbance in a transparent step-hole nozzle and its effect on external flows

Shangze Yang et al.

FUEL (2020)

Add to Collection

Article Energy & Fuels

Experimental study of the spray collapse process of multi-hole gasoline fuel injection at flash boiling conditions

Shengqi Wu et al.

FUEL (2019)

Add to Collection

Article Engineering, Mechanical

Dynamic characteristics of in-nozzle flash boiling bubbles and corresponding temporal responses of external spray

Shangze Yang et al.

EXPERIMENTS IN FLUIDS (2019)

Add to Collection

Article Thermodynamics

Investigation of two-hole flash-boiling plume-to-plume interaction and its impact on spray collapse

Qinglin Xu et al.

INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER (2019)

Add to Collection

Article Energy & Fuels

Investigations on near-field atomization of flash boiling sprays for gasoline direct injection related applications

Xuesong Li et al.

FUEL (2019)

Add to Collection

Article Thermodynamics

Influence of flash boiling spray on the combustion characteristics of a spark-ignition direct-injection optical engine under cold start

Jie Yang et al.

COMBUSTION AND FLAME (2018)

Add to Collection

Article Energy & Fuels

Microscopic behavior of spray droplets under flat-wall impinging condition

Hongliang Luo et al.

FUEL (2018)

Add to Collection

Article Mechanics

Numerical and experimental study of spray impingement and liquid film separation during the spray/wall interaction at expanding corners

Yanzhi Zhang et al.

INTERNATIONAL JOURNAL OF MULTIPHASE FLOW (2018)

Add to Collection

Article Energy & Fuels

Generalizing the behavior of flash-boiling, plume interaction and spray collapse for multi-hole, direct injection

J. Lacey et al.

FUEL (2017)

Add to Collection

Article Thermodynamics

Investigations of effect of phase change mass transfer rate on cavitation process with homogeneous relaxation model

Zhixia He et al.

INTERNATIONAL COMMUNICATIONS IN HEAT AND MASS TRANSFER (2017)

Add to Collection

Article Energy & Fuels

Near-nozzle spray and spray collapse characteristics of spark-ignition direct-injection fuel injectors under sub-cooled and superheated conditions

Shengqi Wu et al.

FUEL (2016)

Add to Collection

© Peeref 2019-2024. All rights reserved.