Related references
Note: Only part of the references are listed.Influence of specimen size on the mechanical properties of microlattices obtained by selective laser melting
Matteo Gavazzoni et al.
PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART C-JOURNAL OF MECHANICAL ENGINEERING SCIENCE (2021)
Experimental and numerical mechanical characterization of additively manufactured Ti6Al4V lattice structures considering progressive damage
Sven Druecker et al.
INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2021)
Architected cellular materials: A review on their mechanical properties towards fatigue-tolerant design and fabrication
M. Benedetti et al.
MATERIALS SCIENCE & ENGINEERING R-REPORTS (2021)
Additively manufactured Ti-6Al-4V thin struts via laser powder bed fusion: Effect of building orientation on geometrical accuracy and mechanical properties
S. Murchio et al.
JOURNAL OF THE MECHANICAL BEHAVIOR OF BIOMEDICAL MATERIALS (2021)
Uniaxial static mechanical properties of regular, irregular and random additively manufactured cellular materials: Nominal vs. real geometry
Sunil Raghavendra et al.
FORCES IN MECHANICS (2021)
Analysis of strain and stress concentrations in micro-lattice structures manufactured by SLM
Laura Boniotti et al.
RAPID PROTOTYPING JOURNAL (2020)
Elastoplastic response and failure assessment of steel alloys: Empirical and computational analyses
Behzad V. Farahani et al.
FATIGUE & FRACTURE OF ENGINEERING MATERIALS & STRUCTURES (2019)
Multifield modelling and failure prediction of cellular cores produced by selective laser melting
George Lampeas et al.
FATIGUE & FRACTURE OF ENGINEERING MATERIALS & STRUCTURES (2019)
Experimental and numerical investigation on compressive fatigue strength of lattice structures of AlSi7Mg manufactured by SLM
L. Boniotti et al.
INTERNATIONAL JOURNAL OF FATIGUE (2019)
Imperfect architected materials: Mechanics and topology optimization
Damiano Pasini et al.
MRS BULLETIN (2019)
Elastically-isotropic truss lattice materials of reduced plastic anisotropy
Thomas Tancogne-Dejean et al.
INTERNATIONAL JOURNAL OF SOLIDS AND STRUCTURES (2018)
Isolated and modulated effects of topology and material type on the mechanical properties of additively manufactured porous biomaterials
R. Hedayati et al.
JOURNAL OF THE MECHANICAL BEHAVIOR OF BIOMEDICAL MATERIALS (2018)
Mechanical properties and deformation behavior of additively manufactured lattice structures of stainless steel
Patrick Koehnen et al.
MATERIALS & DESIGN (2018)
Compression behavior of lattice structures produced by selective laser melting: X-ray tomography based experimental and finite element up approaches
Yasin Amani et al.
ACTA MATERIALIA (2018)
Two-Scale Tomography Based Finite Element Modeling of Plasticity and Damage in Aluminum Foams
Yasin Amani et al.
MATERIALS (2018)
Stiffness and yield strength of architectured foams based on the Schwarz Primitive triply periodic minimal surface
Dong-Wook Lee et al.
INTERNATIONAL JOURNAL OF PLASTICITY (2017)
Elastic and failure response of imperfect three-dimensional metallic lattices: the role of geometric defects induced by Selective Laser Melting
Lu Liu et al.
JOURNAL OF THE MECHANICS AND PHYSICS OF SOLIDS (2017)
Mechanical characterization of structurally porous biomaterials built via additive manufacturing: experiments, predictive models, and design maps for load-bearing bone replacement implants
D. Melancon et al.
ACTA BIOMATERIALIA (2017)
Additively manufactured metallic porous biomaterials based on minimal surfaces: A unique combination of topological, mechanical, and mass transport properties
F. S. L. Bobbert et al.
ACTA BIOMATERIALIA (2017)
High-strength porous biomaterials for bone replacement: A strategy to assess the interplay between cell morphology, mechanical properties, bone ingrowth and manufacturing constraints
Sajad Arabnejad et al.
ACTA BIOMATERIALIA (2016)
Estimation of the structure dependent performance of 3-D rapid prototyped membranes
Tim Femmer et al.
CHEMICAL ENGINEERING JOURNAL (2015)
Relationship between unit cell type and porosity and the fatigue behavior of selective laser melted meta-biomaterials
S. Amin Yavari et al.
JOURNAL OF THE MECHANICAL BEHAVIOR OF BIOMEDICAL MATERIALS (2015)
Additively Manufactured Open-Cell Porous Biomaterials Made from Six Different Space-Filling Unit Cells: The Mechanical and Morphological Properties
Seyed Mohammad Ahmadi et al.
MATERIALS (2015)
Pyrolysis of Heavy Oil in the Presence of Supercritical Water: The Reaction Kinetics in Different Phases
Xue-Cai Tan et al.
AICHE JOURNAL (2015)
A finite element unit-cell method for homogenised mechanical properties of heterogeneous plates
A. Schmitz et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2014)
Effects of bio-functionalizing surface treatments on the mechanical behavior of open porous titanium biomaterials
S. Amin Yavari et al.
JOURNAL OF THE MECHANICAL BEHAVIOR OF BIOMEDICAL MATERIALS (2014)
Mechanical properties of lattice materials via asymptotic homogenization and comparison with alternative homogenization methods
Sajad Arabnejad et al.
INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2013)
Mechanical properties of open-cell metallic biomaterials manufactured using additive manufacturing
G. Campoli et al.
MATERIALS & DESIGN (2013)
Multifunctional heat exchangers derived from three-dimensional micro-lattice structures
Kevin J. Maloney et al.
INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER (2012)
An investigation into the compressive properties of stainless steel micro-lattice structures
K. Ushijima et al.
JOURNAL OF SANDWICH STRUCTURES & MATERIALS (2011)
The quasi-static and blast loading response of lattice structures
S. McKown et al.
INTERNATIONAL JOURNAL OF IMPACT ENGINEERING (2008)
The imperfection sensitivity of isotropic two-dimensional elastic lattices
Digby D. Symons et al.
JOURNAL OF APPLIED MECHANICS-TRANSACTIONS OF THE ASME (2008)
A local finite element implementation for imposing periodic boundary conditions on composite micromechanical models
J. M. Tyrus et al.
INTERNATIONAL JOURNAL OF SOLIDS AND STRUCTURES (2007)
The properties of foams and lattices
MF Ashby
PHILOSOPHICAL TRANSACTIONS OF THE ROYAL SOCIETY A-MATHEMATICAL PHYSICAL AND ENGINEERING SCIENCES (2006)
Deformation rate effects on failure modes of open-cell Al foams and textile cellular materials
S Lee et al.
INTERNATIONAL JOURNAL OF SOLIDS AND STRUCTURES (2006)
Non-quadratic yield criterion for orthotropic sheet metals under plane-stress conditions
D Banabic et al.
INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2003)
Mechanical behavior of a three-dimensional truss material
JC Wallach et al.
INTERNATIONAL JOURNAL OF SOLIDS AND STRUCTURES (2001)
Effective properties of the octet-truss lattice material
VS Deshpande et al.
JOURNAL OF THE MECHANICS AND PHYSICS OF SOLIDS (2001)
Simulation of the multi-scale convergence in computational homogenization approaches
K Terada et al.
INTERNATIONAL JOURNAL OF SOLIDS AND STRUCTURES (2000)
Share Paper
