Related references
Note: Only part of the references are listed.The Effects of Cryogenic Process on the AISI M2 Punch Materials and on the Hole Edge Geometry of the DIN EN 10111-98 Sheet Metal Control Arm Parts
Yusuf Arslan
ADVANCES IN MATERIALS SCIENCE AND ENGINEERING (2020)
Investigation of subsurface fatigue crack growth behavior of D2 tool steel (JIS SKD11) based on a novel measurement method
K. Masuda et al.
INTERNATIONAL JOURNAL OF FATIGUE (2020)
Influence of high magnetic field on carbides and the dislocation density during tempering of high Chromium-containing steel
G. H. Wu et al.
JOURNAL OF MAGNETISM AND MAGNETIC MATERIALS (2019)
Mechanical Properties and Microstructure Characterization of AISI D2 and O1 Cold Work Tool Steels
Mohammed Algarni
METALS (2019)
Effect of chrome plating and varying hardness on the fretting fatigue life of AISI D2 components
Furgan Mukhtar et al.
WEAR (2019)
Enhancement of wear resistance and impact toughness of as cast hypoeutectic high chromium cast iron using niobium
Mervat Mohamed Ibrahim et al.
INTERNATIONAL JOURNAL OF CAST METALS RESEARCH (2018)
Microstructure and Mechanical Properties of Thixowelded AISI D2 Tool Steel
M. N. Mohammed et al.
METALS (2018)
Hammer premature wear in mineral crushing process
Mouna Kallel et al.
TRIBOLOGY INTERNATIONAL (2017)
Improvement of Surface Properties of Low Carbon Steel by Nitriding Treatment
F. Z. Benlahreche et al.
ACTA PHYSICA POLONICA A (2017)
Influence of Hardness, Matrix and Carbides in Combination with Nitridation on Abrasive Wear Resistance of X210Cr12 Tool Steel
Martin Orecny et al.
METALS (2016)
Formation of eutectic carbides in Fe-Cr-Mo-C alloy during non-equilibrium crystallization
K. Wieczerzak et al.
MATERIALS & DESIGN (2016)
Microstructural evolution of a heat-treated H23 tool steel
Meilinda Nurbanasari et al.
INTERNATIONAL JOURNAL OF MINERALS METALLURGY AND MATERIALS (2015)
Wear properties of friction stir processed AISI D2 tool steel
Noushin Yasavol et al.
TRIBOLOGY INTERNATIONAL (2015)
Tribological performance of TiN coatings deposited on 304 L stainless steel used for olive-oil extraction
Amir Bahri et al.
WEAR (2015)
Microstructure evolution and abrasive wear behavior of D2 steel
Kritika Singh et al.
WEAR (2015)
Role of machining defects and residual stress on the AISI 304 fatigue crack nucleation
H. Yahyaoui et al.
FATIGUE & FRACTURE OF ENGINEERING MATERIALS & STRUCTURES (2015)
Failure Analysis of Guides Made of High-Strength AISI D2 Tool Steel
C. Scandian et al.
JOURNAL OF FAILURE ANALYSIS AND PREVENTION (2015)
Effect of chromium nitride coatings and cryogenic treatments on wear and fretting fatigue resistance of aluminum
Volker Franco Steier et al.
ELECTRIC POWER SYSTEMS RESEARCH (2014)
Thixo-joining of D2 and M2 tool steels: analysis of microstructure and mechanical properties
Ali Kalaki et al.
INTERNATIONAL JOURNAL OF MATERIALS RESEARCH (2014)
Comparing microstructure and mechanical properties of AISI D2 steel after bright hardening and oil quenching
H. Torkamani et al.
MATERIALS & DESIGN (2014)
Cracks formation and residual stress in chromium carbide overlays
Liang Ma et al.
ENGINEERING FAILURE ANALYSIS (2013)
Study of Carbide Evolution During Thermo-Mechanical Processing of AISI D2 Tool Steel
D. Bombac et al.
JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2013)
The behaviour of the carbides of ledeburitic AISI D2 tool steel during multiple hot deformation cycles
T. Vecko Pirtovsek et al.
MATERIALS CHARACTERIZATION (2013)
Effect of cerium and lanthanum on the microstructure and mechanical properties of AISI D2 tool steel
Mohammad Ali Hamidzadeh et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2013)
A study on the microstructure and mechanical properties of AISI D2 tool steel modified by niobium
M. A. Hamidzadeh et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2012)
Blanking punch life improvement by laser cladding
Matej Pleterski et al.
ENGINEERING FAILURE ANALYSIS (2011)
Fracture Toughness Determination of Heat Treated AISI D2 Tool Steel Using AE Technique
Cevat Teymuri Sindi et al.
ISIJ INTERNATIONAL (2011)
Effect of tempering conditions on wear resistance in various wear mechanisms of H13 steel
M. X. Wei et al.
TRIBOLOGY INTERNATIONAL (2011)
Experimental investigation of hardfaced martensitic steel under slurry abrasion conditions
S. G. Sapate et al.
MATERIALS & DESIGN (2010)
Sub-zero treatments of AISI D2 steel: Part I. Microstructure and hardness
Debdulal Das et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2010)
On the refinement of carbide precipitates by cryotreatment in AISI D2 steel
D. Das et al.
PHILOSOPHICAL MAGAZINE (2009)
Influence of varied cryotreatment on the wear behavior of AISI D2 steel
D. Dasa et al.
WEAR (2009)
The effect of some heat treatment parameters on the dimensional stability of AISI D2
Cord Henrik Surberg et al.
CRYOGENICS (2008)
Fractographic evaluation of gigacycle fatigue crack nucleation and propagation of a high Cr alloyed cold work tool steel
Christian R. Sohar et al.
INTERNATIONAL JOURNAL OF FATIGUE (2008)
Comparison of wear properties of tool steels AISI D2 and O1 with the same hardness
L Bourithis et al.
TRIBOLOGY INTERNATIONAL (2006)
Effects of the cryogenic cooling on the fatigue strength of the AISI 304 stainless steel ground components
Nabil Ben Fredj et al.
CRYOGENICS (2006)
Influence of chromium carbide coating on tribological performance of steel
S Sen
MATERIALS & DESIGN (2006)
Wear behaviour on the radius portion of a die in deep-drawing: Identification, localisation and evolution of the surface damage
C Boher et al.
WEAR (2005)
Fatigue of cold-work tool steels: Effect of heat treatment and carbide morphology on fatigue crack formation, life, and fracture surface observations
K Fukaura et al.
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE (2004)
Scouring erosion resistance of metallic materials used in slurry pump service
RJ Llewellyn et al.
WEAR (2004)
Friction damage of aluminium alloys
K Elleuch et al.
INDUSTRIAL LUBRICATION AND TRIBOLOGY (2003)
Effect of deep cryogenic treatment on the mechanical properties of tool steels
A Molinari et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2001)
Share Paper
