Related references
Note: Only part of the references are listed.Characterization and modelling of cure-dependent properties and strains during composites manufacturing
Laure Moretti et al.
JOURNAL OF COMPOSITE MATERIALS (2020)
Modeling the influence of interleaf layers in composite materials on elastic properties, thermal expansion, and chemical shrinkage
Tim Frerich et al.
JOURNAL OF COMPOSITE MATERIALS (2019)
In situ real-time 3D observation of porosity growth during composite part curing by ultra-fast synchrotron X-ray microtomography
Basile de Parscau du Plessix et al.
JOURNAL OF COMPOSITE MATERIALS (2019)
Measuring the negative pressure during processing of advanced composites
Navid Zobeiry et al.
COMPOSITE STRUCTURES (2018)
A Review on the Mechanical Modeling of Composite Manufacturing Processes
Ismet Baran et al.
ARCHIVES OF COMPUTATIONAL METHODS IN ENGINEERING (2017)
Bulk modulus evolution of thermoset resins during crosslinking: Is a direct and accurate measurement possible?
Mael Peron et al.
JOURNAL OF COMPOSITE MATERIALS (2017)
PvT-HADDOC: A multi-axial strain analyzer and cure monitoring device for thermoset composites characterization during manufacturing
Mael Peron et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2017)
Monitoring the gelation and effective chemical shrinkage of composite curing process with a novel FBG approach
Haixiao Hu et al.
COMPOSITE STRUCTURES (2017)
Composite cure simulation scheme fully integrating internal strain measurement
Shu Minakuchi et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2016)
Effect of pressure and reinforcement type on the volume chemical shrinkage in thermoset resin and composite
Yasir Nawab et al.
JOURNAL OF COMPOSITE MATERIALS (2014)
Chemical shrinkage characterization techniques for thermoset resins and associated composites
Yasir Nawab et al.
JOURNAL OF MATERIALS SCIENCE (2013)
Determination and modelling of the cure shrinkage of epoxy vinylester resin and associated composites by considering thermal gradients
Yasir Nawab et al.
COMPOSITES SCIENCE AND TECHNOLOGY (2012)
Material characterization and residual stresses simulation during the manufacturing process of epoxy matrix composites
Y. Abou Msallem et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2010)
Coupled visco-mechanical and diffusion void growth modelling during composite curing
Y. Ledru et al.
COMPOSITES SCIENCE AND TECHNOLOGY (2010)
Cure Kinetics Modeling and Cure Shrinkage Behavior of a Thermosetting Composite
Nuri Ersoy et al.
POLYMER ENGINEERING AND SCIENCE (2010)
Behaviour of a moulded composite part: Modelling of dilatometric curve (constant pressure) or pressure (constant volume) with temperature and conversion degree gradients
N. Boyard et al.
COMPOSITES SCIENCE AND TECHNOLOGY (2007)
In situ measurements of through-the-thickness strains during processing of AS4/8552 composite
Tomasz Garstka et al.
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2007)
A note upon the development of residual curing strains in carbon/epoxy laminates. Study by thermomechanical analysis
PA Olivier
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING (2006)
Cure shrinkage measurement of nonconductive adhesives by means of a thermomechanical analyzer
H Yu et al.
JOURNAL OF ELECTRONIC MATERIALS (2005)
In-situ measurement of chemical shrinkage of MY750 epoxy resin by a novel gravimetric method
C Li et al.
COMPOSITES SCIENCE AND TECHNOLOGY (2004)
A new method to reduce cure-induced stresses in thermoset polymer composites, part II: Closed loop feedback control system
MS Genidy et al.
JOURNAL OF COMPOSITE MATERIALS (2000)
Share Paper
