Related references
Note: Only part of the references are listed.The Influence of Tool Rake Surface Geometry on the Hard Turning Process of AISI52100 Hardened Steel
Hanzhong Xu et al.
MATERIALS (2019)
Enhancing Productivity by Means of High Feed Rate in the Drilling of Al 2011 Aluminium Alloy
R. E. R. Pacheco et al.
ARABIAN JOURNAL FOR SCIENCE AND ENGINEERING (2019)
Influence of Different Cooling Methods on Tool Life, Wear Mechanisms and Surface Roughness in the Milling of Nickel-Based Waspaloy with WC Tools
Cagri Vakkas Yildirim et al.
ARABIAN JOURNAL FOR SCIENCE AND ENGINEERING (2019)
Experimental study of the wear behavior of PCBN inserts during cutting of GH4169 superalloys under high-pressure cooling
Lubin Li et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2018)
Influences of cutting fluid conditions and cutting parameters on surface integrity of Inconel 718 under high-pressure jet-assisted machining (HPJAM)
Aziz Ul Hassan Mohsan et al.
LUBRICATION SCIENCE (2018)
Statistical analysis of cutting forces and hole accuracy in reaming an Al-Si-Mg alloy (6351) with different copper contents
Ricardo Augusto Goncalves et al.
JOURNAL OF THE BRAZILIAN SOCIETY OF MECHANICAL SCIENCES AND ENGINEERING (2018)
Study on cutting force and hole quality of PCD step reamer for reaming ZL102 alloy in dry and wet conditions
Yongguo Wang et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2017)
Effects of high-pressure cooling on the wear patterns on turning inserts used on alloy IN718
A. Suarez et al.
MATERIALS AND MANUFACTURING PROCESSES (2017)
Acoustic emission signal analysis during chip formation process in high speed machining of 7050-T7451 aluminum alloy and Inconel 718 superalloy
Bing Wang et al.
JOURNAL OF MANUFACTURING PROCESSES (2017)
Investigations of critical cutting speed and ductile-to-brittle transition mechanism for workpiece material in ultra-high speed machining
Bing Wang et al.
INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES (2015)
Effect of conventional and non-conventional tool geometries to skewness and kurtosis of surface roughness in case of fine turning of aluminium alloys with diamond tools
Richard Horvath et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2015)
Surface morphology and microcrack formation for 7050-T7451 aluminum alloy in high speed milling
Zhaolin Zhong et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2015)
Serrated chip formation mechanism based on mixed mode of ductile fracture and adiabatic shear
Bing Wang et al.
PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE (2014)
Analysis of the machining characteristics in reaming AlSi12 alloy with PCD reamer
Xiangping Yan et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2013)
Tool life and wear mechanisms in high speed machining of Ti-6Al-4V alloy with PCD tools under various coolant pressures
Rosemar B. da Silva et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2013)
Effect of high-pressure cooling on life of SiAlON tools in machining of Inconel 718
Zydrunas Vagnorius et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2011)
Effects of pre-stretching and ageing on the strength and fracture toughness of aluminum alloy 7050
NianMei Han et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2011)
Al7050-T7451 turning simulation based on the modified power-law material model
Feng Jiang et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2010)
Investigation and optimization of lubrication parameters in high speed turning of superalloy Inconel 718
Dinesh G. Thakur et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2010)
HIGH PRESSURE WATER JET ASSISTED MACHINING OF DUPLEX STEEL: MACHINABILITY AND TOOL LIFE
T. Braham-Bouchnak et al.
INTERNATIONAL JOURNAL OF MATERIAL FORMING (2010)
Some studies on high-pressure cooling in turning of Ti-6Al-4V
A. K. Nandy et al.
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE (2009)
Performance evaluation of chip breaker utilizing neural network
Hong-Gyoo Kim et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2009)
Investigation on capability of the reaming process using minimal quantity lubrication
Leonardo De Chiffre et al.
CIRP JOURNAL OF MANUFACTURING SCIENCE AND TECHNOLOGY (2009)
Finite element modeling of low speed reaming vibrations with reamer geometry modifications
S. Towfighian et al.
JOURNAL OF INTELLIGENT MANUFACTURING (2007)
Evaluation of machining performance of MMC with PCBN and PCD tools
X Ding et al.
WEAR (2005)
Cooling ability of cutting fluids and measurement of the chip-tool interface temperatures
WF Sales et al.
INDUSTRIAL LUBRICATION AND TRIBOLOGY (2002)
Analysis of tool oscillation and hole roundness error in a quasi-static model of reaming
PV Bayly et al.
JOURNAL OF MANUFACTURING SCIENCE AND ENGINEERING-TRANSACTIONS OF THE ASME (2001)
Effects of machining parameters when reaming aluminium-silicon (SAE 322) alloy
AA Bezerra et al.
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY (2001)
Share Paper
