Related references
Note: Only part of the references are listed.Advances in microcellular injection moulding
Gethin Llewelyn et al.
JOURNAL OF CELLULAR PLASTICS (2020)
A Strategy for Problem Solving of Filling Imbalance in Geometrically Balanced Injection Molds
Krzysztof Wilczynski et al.
POLYMERS (2020)
A kind of special weld lines with high specific strength and elongation obtained by core-back chemical foam injection molding
H. Wu et al.
EXPRESS POLYMER LETTERS (2019)
Modeling and Optimization of the Injection-Molding Process: A Review
Celio Fernandes et al.
ADVANCES IN POLYMER TECHNOLOGY (2018)
A new core-back foam injection molding method with chemical blowing agents
Hao Wu et al.
MATERIALS & DESIGN (2018)
Estimation of the foaming temperature of mold-opening foam injection molding process
Raymond K. M. Chu et al.
JOURNAL OF CELLULAR PLASTICS (2016)
Polymer foaming with chemical blowing agents: Experiment and modeling
Jose Antonio Reglero Ruiz et al.
POLYMER ENGINEERING AND SCIENCE (2015)
EFFECT OF TEMPERATURE AND DENSITY VARIATIONS ON THERMAL CONDUCTIVITY OF POLYSTYRENE INSULATION MATERIALS IN OMAN CLIMATE
M. Khoukhi et al.
JOURNAL OF ENGINEERING PHYSICS AND THERMOPHYSICS (2015)
Development of high void fraction polylactide composite foams using injection molding: Mechanical and thermal insulation properties
A. Ameli et al.
COMPOSITES SCIENCE AND TECHNOLOGY (2014)
Influence of the injection moulding parameters on the microstructure and thermal properties of microcellular polyethylene terephthalate glycol foams
Jaime Francisco Gomez-Gomez et al.
JOURNAL OF CELLULAR PLASTICS (2013)
Influence and prediction of processing parameters on the properties of microcellular injection molded thermoplastic polyurethane based on an orthogonal array test
Hao-Yang Mi et al.
JOURNAL OF CELLULAR PLASTICS (2013)
The Effect of Injection Molding Conditions on the Morphology of Polymer Structural Foams
M. Reza Barzegari et al.
POLYMER ENGINEERING AND SCIENCE (2009)
Strategies to Achieve a Uniform Cell Structure with a High Void Fraction in Advanced Structural Foam Molding
John W. S. Lee et al.
INDUSTRIAL & ENGINEERING CHEMISTRY RESEARCH (2008)
The dimensional stability of a microcellular injection molded gear shaft
Shyh-Shin Hwang et al.
INTERNATIONAL COMMUNICATIONS IN HEAT AND MASS TRANSFER (2008)
Rheological behavior of a microcellular, oil-extended ethylene-propylene-diene rubber compound: Effects of the blowing agent, curing agent, and conductive carbon black filler
S. P. Mahapatra et al.
JOURNAL OF APPLIED POLYMER SCIENCE (2008)
Cell structure and dynamic properties of injection molded polypropylene foams
Ming-Cheng Guo et al.
POLYMER ENGINEERING AND SCIENCE (2007)
Effects of the chemical foaming agents, injection parameters, and melt-flow index on the microstructure and mechanical properties of microcellular injection-molded wood-fiber/polypropylene composites
AK Bledzki et al.
JOURNAL OF APPLIED POLYMER SCIENCE (2005)
A role for 'one-factor-at-a-time' experimentation in parameter design
DD Frey et al.
RESEARCH IN ENGINEERING DESIGN (2003)
Effect of process conditions on the weld-line strength and microstructure of microcellular injection molded parts
LS Turng et al.
POLYMER ENGINEERING AND SCIENCE (2003)
Shear stress nucleation in microcellular foaming process
L Chen et al.
POLYMER ENGINEERING AND SCIENCE (2002)
Foaming of aliphatic polyester using chemical blowing agent
DJ Kim et al.
JOURNAL OF APPLIED POLYMER SCIENCE (2001)
Share Paper
