Related references
Note: Only part of the references are listed.The effect of lubricant additives on the tribological performance of oil and gas drilling applications up to 200 °C
Pixiang Lan et al.
TRIBOLOGY INTERNATIONAL (2020)
Enhancements in the tribological performance of environmentally friendly water-based drilling fluids using additives
Yong Zheng et al.
APPLIED SURFACE SCIENCE (2020)
Influence of additives on the friction and wear reduction of oil-based drilling fluid
Mohammad Humood et al.
WEAR (2019)
A Drill Bit and a Drilling Motor With Embedded High-Frequency (1600 Hz) Drilling Dynamics Sensors Provide New Insights Into Challenging Downhole Drilling Conditions
Junichi Sugiura et al.
SPE DRILLING & COMPLETION (2019)
Tribological performance of aromatic thermosetting polyester (ATSP) coatings under cryogenic conditions
Pixiang Lan et al.
WEAR (2018)
Experimental study of improved rheology and lubricity of drilling fluids enhanced with nano-particles
O. Anwar Beg et al.
APPLIED NANOSCIENCE (2018)
Elevated-Temperature and -Pressure Tribology of Drilling Fluids Used in Oil and Gas Extended-Reach-Drilling Applications
Pixiang Lan et al.
SPE JOURNAL (2018)
A critical review of the coiled tubing friction-reducing technologies in extended-reach wells. Part 1: Lubricants
Silviu Livescu et al.
JOURNAL OF PETROLEUM SCIENCE AND ENGINEERING (2017)
Nanoparticles based drilling muds a solution to drill elevated temperature wells: A review
A. Aftab et al.
RENEWABLE & SUSTAINABLE ENERGY REVIEWS (2017)
Effectiveness of phosphonium cation-based ionic liquids as lubricant additive
R. Gonzalez et al.
TRIBOLOGY INTERNATIONAL (2016)
Performance of low solid bentonite drilling fluids modified by cellulose nanoparticles
Kunlin Song et al.
JOURNAL OF NATURAL GAS SCIENCE AND ENGINEERING (2016)
The effect of the TiO2/polyacrylamide nanocomposite on water-based drilling fluid properties
Mehran Sadeghalvaad et al.
POWDER TECHNOLOGY (2015)
Friction and wear characteristics of steel on rock under water and oil based lubricated sliding conditions
A. Taghipour et al.
TRIBOLOGY-MATERIALS SURFACES & INTERFACES (2015)
Influence of viscosity modifier nature and concentration on the viscous flow behaviour of oil-based drilling fluids at high pressure
J. Hermoso et al.
APPLIED CLAY SCIENCE (2014)
A review of recent developments of friction modifiers for liquid lubricants (2007-present)
Zhenglin Tang et al.
CURRENT OPINION IN SOLID STATE & MATERIALS SCIENCE (2014)
Investigation of the Mitigation of Lost Circulation in Oil-Based Drilling Fluids by Use of Gilsonite
H. Guo et al.
SPE JOURNAL (2014)
Tribological performance and tribochemical processes in a DLC/steel system when lubricated in a fully formulated oil and base oil
S. Kosarieh et al.
SURFACE & COATINGS TECHNOLOGY (2013)
Water Use for Shale-Gas Production in Texas, US
Jean-Philippe Nicot et al.
ENVIRONMENTAL SCIENCE & TECHNOLOGY (2012)
The Interactions Between Sulfur-Nitrided Layer on Steel Surface and MoDTC Lubricating Additive and Their Effects on Tribological Performance
Chunyue Liu et al.
TRIBOLOGY LETTERS (2012)
Effect of Extreme Load on Plain ZDDP Oil in the Presence of FeF3 Catalyst Using Design of Experiment and Fundamental Study under Two Different Rotational Speeds
Gabi Nehme
TRIBOLOGY TRANSACTIONS (2012)
Effects of interactions between solids and surfactants on the tribological properties of water-based drilling fluids
J. M. Gonzalez et al.
COLLOIDS AND SURFACES A-PHYSICOCHEMICAL AND ENGINEERING ASPECTS (2011)
Natural Gas Plays in the Marcellus Shale: Challenges and Potential Opportunities
David M. Kargbo et al.
ENVIRONMENTAL SCIENCE & TECHNOLOGY (2010)
Friction factors: What are they for torque, drag, vibration, bottom hole assembly and transient surge/swab analyses?
Robello Samuel
JOURNAL OF PETROLEUM SCIENCE AND ENGINEERING (2010)
Prediction of casing wear in extended-reach drilling
Gao Deli et al.
PETROLEUM SCIENCE (2010)
Influence of pressure and temperature dependence of thermal properties of a lubricant on the behaviour of circular TEHD contacts
W. Habchi et al.
TRIBOLOGY INTERNATIONAL (2010)
Tribological behaviour of two imidazolium ionic liquids as lubricant additives for steel/steel contacts
A. Hernandez Battez et al.
WEAR (2009)
Effect of oil additives on the durability of hydrogenated DLC coating under boundary lubrication conditions
T. Haque et al.
WEAR (2009)
Tribological properties of ionic liquids as lubricants and additives. Part 1: synergistic tribofilm formation between ionic liquids and tricresyl phosphate
M. F. Fox et al.
PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART J-JOURNAL OF ENGINEERING TRIBOLOGY (2008)
Understanding the tribological chemistry of chlorine-, sulfur- and phosphorus-containing additives
O. Furlong et al.
TRIBOLOGY INTERNATIONAL (2007)
Effect and mechanism of additives for ionic liquids as new lubricants
Hideto Kamimura et al.
TRIBOLOGY INTERNATIONAL (2007)
Study of surface films of overbased sulfonates and sulfurized olefins by X-Ray Absorption Near Edge Structure (XANES) spectroscopy
Michael T. Costello et al.
TRIBOLOGY LETTERS (2006)
A multi-technique approach of tribofilm characterisation
C Minfray et al.
THIN SOLID FILMS (2004)
Antiwear tribofilm formation on steel surfaces lubricated with gear oil containing borate, phosphorus, and sulfur additives
K Komvopoulos et al.
TRIBOLOGY TRANSACTIONS (2002)
Transfer films and friction under boundary lubrication
JM Martin et al.
WEAR (2000)
Lubricant thermal conductivity and heat capacity under high pressure
R Larsson et al.
PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART J-JOURNAL OF ENGINEERING TRIBOLOGY (2000)