Related references
Note: Only part of the references are listed.The influence of protein concentration, temperature and cathodic polarization on the surface status of CoCrMo biomedical grade alloys
Righdan Namus et al.
APPLIED SURFACE SCIENCE (2020)
Influence of protein adsorption on tribocorrosion behaviour of CoCrMo biomedical-grade alloys
Righdan Namus et al.
TRIBOLOGY INTERNATIONAL (2020)
Factors influencing superplasticity in the Ti-6Al-4V alloy Processed by high-pressure torsion
Hamed Shahmir et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2018)
Correlation of the wear transition in CoCrMo alloys with the formation of a nanocrystalline surface layer and a proteinaceous surface film
R. Namus et al.
WEAR (2017)
Electrochemical Quartz Crystal Microbalance and X-Ray Photoelectron Spectroscopy study of cathodic reactions in Bovine Serum Albumin containing solutions on a Physical Vapour Deposition-CoCrMo biomedical alloy
A. Igual Munoz et al.
ELECTROCHIMICA ACTA (2015)
Subsurface characterisation of wear on mechanically polished and electro-polished biomedical grade CoCrMo
P. Zeng et al.
WEAR (2015)
Passive behavior of a bulk nanostructured 316L austenitic stainless steel consisting of nanometer-sized grains with embedded nano-twin bundles
Tianshu Li et al.
CORROSION SCIENCE (2014)
Corrosion behaviour of CoCrMo alloys in 2 wt% sulphuric acid solution
Xiaoqing Zhang et al.
ELECTROCHIMICA ACTA (2014)
Results ot Birmingham hip resurfacing at 12 to 15 years
J. Daniel et al.
BONE & JOINT JOURNAL (2014)
Influence of phase volume fractions on the processing of a Ti-6Al-4V alloy by high-pressure torsion
Ying Chun Wang et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2013)
Mechanical and electrochemical deterioration mechanisms in the tribocorrosion of Al alloys in NaCl and in NaNO3 solutions
A. C. Vieira et al.
CORROSION SCIENCE (2012)
Dynamic surface microstructural changes during tribological contact that determine the wear behaviour of hip prostheses: metals and ceramics
W. Mark Rainforth et al.
FARADAY DISCUSSIONS (2012)
The tribological difference between biomedical steels and CoCrMo-alloys
Alfons Fischer et al.
JOURNAL OF THE MECHANICAL BEHAVIOR OF BIOMEDICAL MATERIALS (2012)
Failure rates of metal-on-metal hip resurfacings: analysis of data from the National Joint Registry for England and Wales
Alison J. Smith et al.
LANCET (2012)
Electrochemical Simulation of the Current and Potential Response in Sliding Tribocorrosion
N. Papageorgiou et al.
TRIBOLOGY LETTERS (2012)
Five-Year Results of the ASR XL Acetabular System and the ASR Hip Resurfacing System
Richard N de Steiger et al.
JOURNAL OF BONE AND JOINT SURGERY-AMERICAN VOLUME (2011)
Using finite element modeling to examine the flow processes in quasi-constrained high-pressure torsion
Roberto B. Figueiredo et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2011)
Influence of strain rate on the characteristics of a magnesium alloy processed by high-pressure torsion
Pauline Serre et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2011)
Effect of equal-channel angular extrusion on mechanical and wear properties of eutectic Al-12Si alloy
Tevfik Kucukomeroglu
MATERIALS & DESIGN (2010)
Revealing the relationship between grain size and corrosion rate of metals
K. D. Ralston et al.
SCRIPTA MATERIALIA (2010)
Mechanical and wear properties of ultrafine-grained pure Ti produced by multi-pass equal-channel angular extrusion
G. Purcek et al.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING (2009)
Micro-structural alterations within different areas of articulating surfaces of a metal-on-metal hip resurfacing system
R. Pourzal et al.
WEAR (2009)
The evolution of homogeneity in an aluminum alloy processed using high-pressure torsion
Cheng Xu et al.
ACTA MATERIALIA (2008)
Corrosion resistance and microstructure of electrodeposited nickel-cobalt alloy coatings
Meenu Srivastava et al.
SURFACE & COATINGS TECHNOLOGY (2006)
Tribocorrosion in implants - assessing high carbon and low carbon Co-Cr-Mo alloys by in situ electrochemical measurements
Yu Yan et al.
TRIBOLOGY INTERNATIONAL (2006)
Understanding the role of corrosion in the degradation of metal-on-metal implants
Y Yan et al.
PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART H-JOURNAL OF ENGINEERING IN MEDICINE (2006)
Microstructural effects on the wear resistance of wrought and as-cast Co-Cr-Mo-C implant alloys
AJ Saldívar-García et al.
JOURNAL OF BIOMEDICAL MATERIALS RESEARCH PART A (2005)
The pathways of dynamic recrystallization in all-metal hip joints
R Büscher et al.
WEAR (2005)
The long-term wear of retrieved McKee-Farrar metal-on-metal total hip prostheses
DW Howie et al.
JOURNAL OF ARTHROPLASTY (2005)
Corrosion resistance of ultra fine-grained Ti
A Balyanov et al.
SCRIPTA MATERIALIA (2004)
Tribochemical reaction on metal-on-metal hip joint bearings -: A comparison between in-vitro and in-vivo results
MA Wimmer et al.
WEAR (2003)
Nanoindentation stress-strain curves as a method for thin-film complete mechanical characterization:: application to nanometric CrN/Cr multilayer coatings
E Martínez et al.
APPLIED PHYSICS A-MATERIALS SCIENCE & PROCESSING (2003)
The acting wear mechanisms on metal-on-metal hip joint bearings:: in vitro results
MA Wimmer et al.
WEAR (2001)
Share Paper
