Related references
Note: Only part of the references are listed.Study on hydrophobic properties of fluororubber prepared by template method under high temperature conditions
Qiang He et al.
COLLOIDS AND SURFACES A-PHYSICOCHEMICAL AND ENGINEERING ASPECTS (2021)
Effect of Particle Size on Tribological Properties of Rubber/Steel Seal Pairs Under Contaminated Water Lubrication Conditions
Ming-xue Shen et al.
TRIBOLOGY LETTERS (2020)
Non-uniform abrasive particle size effects on friction characteristics of FKM O-ring seals under three-body abrasion
Kun Qin et al.
TRIBOLOGY INTERNATIONAL (2019)
The effect of wear on the frictional vibration suppression of water-lubricated rubber slat with/without surface texture
Jun Yang et al.
WEAR (2019)
The Application of Downhole Vibration Factor in Drilling Tool Reliability Big Data Analytics-A Review
Yali Ren et al.
ASCE-ASME JOURNAL OF RISK AND UNCERTAINTY IN ENGINEERING SYSTEMS PART B-MECHANICAL ENGINEERING (2019)
Surface Roughness Effect on the Friction and Wear Behaviour of Acrylonitrile-Butadiene Rubber (NBR) Under Oil Lubrication
Dong Feng et al.
TRIBOLOGY LETTERS (2017)
Effect of abrasive size on friction and wear characteristics of nitrile butadiene rubber (NBR) in two-body abrasion
Ming-Xue Shen et al.
TRIBOLOGY INTERNATIONAL (2016)
Material properties and tool performance of PCD reinforced WC matrix composites for hardbanding applications
Kai Zhang et al.
INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS (2015)
Dry sliding friction and casing wear behavior of PCD reinforced WC matrix composites
Kai Zhang et al.
TRIBOLOGY INTERNATIONAL (2015)
Influence of Al2O3 particles on the friction and wear behaviors of nitrile rubber against 316L stainless steel
Ming-xue Shen et al.
JOURNAL OF ZHEJIANG UNIVERSITY-SCIENCE A (2015)
Characterization of fluoroelastomers by various analytical techniques including pyrolysis gas chromatography/mass spectrometry
John A. Hiltz
JOURNAL OF ANALYTICAL AND APPLIED PYROLYSIS (2014)
Three-body abrasive wear behaviour of aluminium alloys
Saurabh Kumar et al.
PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART J-JOURNAL OF ENGINEERING TRIBOLOGY (2013)
Wear mechanisms and in-service surface modifications of a Stellite 6B Co-Cr alloy
M. Sebastiani et al.
WEAR (2012)
Effect of abrasive particle size and the influence of microstructure on the wear mechanisms in wear-resistant materials
M. R. Thakare et al.
WEAR (2012)
Optimization of contact pressure profile for performance improvement of a rotary elastomeric seal operating in abrasive drilling environment
Ping C. Sui et al.
WEAR (2011)
Particle motion and modes of wear in the dry sand-rubber wheel abrasion test
S. M. Nahvi et al.
WEAR (2009)
Study of relations between viscoelasticity and tribological behaviour of filled elastomer for lip seal application
M. Thomine et al.
TRIBOLOGY INTERNATIONAL (2007)
Micro-abrasion transitions of metallic materials
MM Stack et al.
WEAR (2003)
Wear-mode mapping for the micro-scale abrasion test
K Adachi et al.
WEAR (2003)
Two-body and three-body abrasive wear behaviour of polyaryletherketone composites
AP Harsha et al.
POLYMER TESTING (2003)
Micro-scale abrasion and scratch response of PVD coatings at elevated temperatures
DN Allsopp et al.
WEAR (2001)
Abrasion of mild steel in wet and dry conditions with the rubber and steel wheel abrasion apparatus
S Wirojanupatump et al.
WEAR (2000)
Share Paper
