Related references
Note: Only part of the references are listed.PLA/banana fiber based sustainable biocomposites: A manufacturing perspective
Ujendra Kumar Komal et al.
COMPOSITES PART B-ENGINEERING (2020)
Study of the manufacturing process effects of fused filament fabrication and injection molding on tensile properties of composite PLA-wood parts
M. Damous Zandi et al.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY (2020)
Recyclability analysis of PLA/Sisal fiber biocomposites
Saurabh Chaitanya et al.
COMPOSITES PART B-ENGINEERING (2019)
Comparison of physical and mechanical properties of PLA, ABS and nylon 6 fabricated using fused deposition modeling and injection molding
Makara Lay et al.
COMPOSITES PART B-ENGINEERING (2019)
Additive Manufacturing of PLA and CF/PLA Binding Layer Specimens via Fused Deposition Modeling
Yuhang Li et al.
JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2018)
Effect of Printing Parameters on Tensile, Dynamic Mechanical, and Thermoelectric Properties of FDM 3D Printed CABS/ZnO Composites
Yah Yun Aw et al.
MATERIALS (2018)
Polylactide (PLA) Filaments a Biobased Solution for Additive Manufacturing: Correlating Rheology and Thermomechanical Properties with Printing Quality
Gianluca Cicala et al.
MATERIALS (2018)
The Influence of Manufacturing Parameters on the Mechanical Behaviour of PLA and ABS Pieces Manufactured by FDM: A Comparative Analysis
Adrian Rodriguez-Panes et al.
MATERIALS (2018)
Improving the Impact Strength and Heat Resistance of 3D Printed Models: Structure, Property, and Processing Correlationships during Fused Deposition Modeling (FDM) of Poly(Lactic Acid)
Claire Benwood et al.
ACS OMEGA (2018)
Fused Deposition Technique for Continuous Fiber Reinforced Thermoplastic
Paolo Bettini et al.
JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE (2017)
Measurements of the mechanical response of unidirectional 3D-printed PLA
Y. Song et al.
MATERIALS & DESIGN (2017)
The impact of nozzle and bed temperatures on the fracture resistance of FDM printed materials
Nahal Aliheidari et al.
BEHAVIOR AND MECHANICS OF MULTIFUNCTIONAL MATERIALS AND COMPOSITES 2017 (2017)
Development and Application of Wood Flour-Filled Polylactic Acid Composite Filament for 3D Printing
Yubo Tao et al.
MATERIALS (2017)
3D printing of polymer matrix composites: A review and prospective
Xin Wang et al.
COMPOSITES PART B-ENGINEERING (2017)
3D printing with polymers: Challenges among expanding options and opportunities
Jeffrey W. Stansbury et al.
DENTAL MATERIALS (2016)
Fused deposition modeling with polypropylene
O. S. Carneiro et al.
MATERIALS & DESIGN (2015)
Development and characterization of PLA-based green composites: A review
Pramendra Kumar Bajpai et al.
JOURNAL OF THERMOPLASTIC COMPOSITE MATERIALS (2014)
Mechanical properties of components fabricated with open-source 3-D printers under realistic environmental conditions
B. M. Tymrak et al.
MATERIALS & DESIGN (2014)
Deposition direction-dependent failure criteria for fused deposition modeling polycarbonate
Nevin Hill et al.
RAPID PROTOTYPING JOURNAL (2014)
Poly(lactic acid) crystallization
Sajjad Saeidlou et al.
PROGRESS IN POLYMER SCIENCE (2012)
Crystallization Behavior of Poly(ε-caprolactone)/Layered Double Hydroxide Nanocomposites
Zhe Yang et al.
JOURNAL OF APPLIED POLYMER SCIENCE (2010)
Share Paper
